change language INFINITI M HYBRID 2013 Navigation Manual

Black plate (58,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
3. Map settings
3-14
.[Long Range]:
Sets the long range map view display
on/off.
“Settings long range map view”
(page 3-15)
. [Map Color]:
Changes the map color.
“Setting map color” (page 3-16)
. [Birdview Angle]:
Changes the Birdview
TMangle.
“Changing BirdviewTMangle”
(page 3-16)
. [Left Split Map Settings]:
Sets the map settings for the left screen
of the split map.
“Setting left screen display”
(page 3-17)
. [Show all Freeway Exits on Route]/
[Auto. Show Turn List on Freeway]:
Sets the display of the freeway exit
information on/off.
“Show exit information on free-
ways” (page 5-11)
Other settings
The orientation of the map can also be set
by performing the following procedure.
IMA01051. Push .
2. Highlight [Navigation] and push
.
3. Highlight [Map View] and push
.
SETTING MAP ORIENTATION
The map direction (orientation) can also be
changed in the 2D map. These settings are
available only in the 2D map or 2D/2D split
map.
IMA01061. Highlight [Map Orientation] and push
.
IMA01072. Highlight the preferred map orientation
and push . The indicator of the
selected map orientation illuminates.
3. Push

Black plate (59,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
on the map.
. [Heading Up]:
The vehicle icon always points up on
the screen and the map rotates.
INFO:
If the map orientation is switched, the direction
indicator icon displayed in the lower left corner
is also switched.
: North Up
: Heading Up
IMA0108North Up
IMA0109Heading Up
INFO:
The direction of the map can also be changed by
touching the direction icon on the map screen.
Voice command
1. Push >located on the steering
wheel.
2. After the tone sounds, speak a com- mand.
To change the map direction:
“North Up” (Alternate Command Mode)
“Heading Up” (Alternate Command
Mode)
SETTINGS LONG RANGE MAP VIEW
The position of the vehicle icon can be
changed to view a wider area in the
traveling direction. If this function is
activated, the vehicle icon is located
slightly lower than the center of the screen.
IMA01101. Highlight [Long Range] and push
. The indicator illuminates.
2. Push

Black plate (60,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
3. Map settings
3-16
INFO:
[Long Range] is displayed only when [Heading
Up] is selected.
SETTING MAP COLOR
The map color can be changed to a warm or
cool color, or a light color, to emphasize
the traffic information.
IMA01121.Highlight [Map Color] and push
.
IMA0113
2. Highlight the preferred map color and
push . The indicator light of the
selected color illuminates.
Available map colors
The following map colors are available. . [Warm]:
Sets warm colors for the map coloring.
. [Cool]:
Sets cool colors for the map coloring.
. [Traffic Emphasis]:
Sets light colors for the map coloring to
emphasize the traffic information.
INFO:
The effect of the setting changes can be
confirmed on the preview displayed on the right
side of the screen.
CHANGING BirdviewTMANGLE
The BirdviewTMangle can be changed.
This setting is available only in the Bird-
view
TMmap or 2D/BirdviewTMsplit map.
IMA01141. Highlight [Birdview Angle] and push .
Condition: Language=NAM_English/

Black plate (61,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IMA01152. Adjust the BirdviewTMangle using the
INFINITI controller.
3. Push

Black plate (69,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
CHANGING REGION
When setting a destination, the correct
region must be selected.
To narrow down the location, the city can
also be specified.
Specifying region
JND0238X1. Push.
2. Highlight [Change Region] and push .
JNB0283X
3. Highlight the preferred region and push.
Available setting items . US1: CA, NV
. US2: AZ, CO, ID, MT, NM, OR, UT, WA,
WY
. US3: IA, KS, MN, MO, ND, NE, SD
. US4: AR, LA, MS, OK, TX
. US5: IL, IN, MI, WI
. US6: DC, DE, KY, MD, OH, PA, VA, WV
. US7: CT, MA, ME, NH, NJ, NY, RI, VT
. US8: AL, FL, GA, NC, SC, TN
. US9: AK
. US10: HI
. Canada
. Puerto Rico
. Virgin Islands
INFO:
.
It is also possible to select a region by
touching the map on the right side of the
screen.
.It is not possible to search for a route from
the continental United States to Hawaii,
Puerto Rico and Virgin Islands.
Specifying city
When searching for a destination with
“Places”, “Freeway Entrance/Exit”, “Inter-
section” or“City Center”, the search can be
narrowed down by specifying the city.
For “City Center”, you can only change the
region.
As an example, the procedure for specify-
ing the city from “Places”is described
here.
IDE01031. Highlight [Select a City] and push
.
4. Setting destination
4-3
Condition: Language=NAM_English/

Black plate (74,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
4. Setting destination
4-8
IDE01184. Set the narrowing down conditions forthe landmarks and push .
INFO:
Highlight [Change Region] and push
to change the region. A screen for
selecting a region is displayed.
“Changing region” (page 4-3)
IDE0119
INFO:
If [Select a City] is highlighted and
is pushed, a city name input screen is
displayed. Specify the city to be searched
before narrowing down the categories.
“Specifying city” (page 4-3)
IDE01205. Highlight the main category from the
list and push .
IDE0121
INFO:
To select a category by directly inputting the
category name, highlight [Category Search]
and push. The category name input
screen is displayed.
IDE01226. Highlight the subcategory and push .
INFO:
Subcategories may not exist depending on
the category that is selected.
IDE0123
Condition: Language=NAM_English/

Black plate (75,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
7.Enter the name of the destination
facility and highlight [List], and then
push .
The facility list is displayed.
INFO:
.It is not necessary to enter the facility name completely. It is also possible to
display the list screen only by high-
lighting [List] without entering the facil-
ity name and pushing .
.The number of narrowed down points are
displayed in the “Matches”column.
.Up to two keywords (part of the facility
name) can be entered by highlighting
[AND Search] and pushing after
entering the first facility name.
IDE0124
INFO:
The facility name can also be entered
directly by highlighting [Choose Name] on
the main category list screen and pushing

IDE01258. Highlight the preferred destination
from the list, and push .
INFO:
.By highlighting [Sort] and pushing
, options can be sorted from
[By Name] or [By Dist.]. When selecting
[By Dist.], the position of the selected
location is displayed in the preview on
the right side of the screen.
.In some cases, when a facility name has
been entered, the number of matching
destinations in the “Matches”column
may be different from the number displayed on the list screen. If this
occurs, enter more characters to further
reduce the number of matches.
.The search conditions can be changed by
highlighting [Refine] and pushing
.
IDE01269. The entire route is shown on the map.
Highlight [Start] after confirming the
location of the displayed destination
and push . The system sets the
destination to the selected location and
starts calculating a route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
4. Setting destination
4-9
Condition: Language=NAM_English/

Black plate (77,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IDE01349. Highlight the preferred destination fa-cility from the list, and then push
.
INFO:
.By highlighting [Sort] and pushing, sorting options can be selected
to re-sort the list.
.The search conditions can be changed by highlighting [Refine].
.By highlighting [Ratings] and pushing, an explanation of the ZAGAT
ratings can be displayed.
IDE013510. The entire route is shown on the map. Highlight [Start] after confirming the
location of the displayed destination
and pushing . The system sets
the destination to the selected location
and starts calculating a route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
*C2009 Zagat Survey, LLC. Zagat Survey is
a registered trademark of Zagat Survey,
LLC.
SETTING HOME AS DESTINATION
The home location can be set as the
destination to which the system calculates
a route. This function is especially useful
when searching for a route to return to the
home location.
JND0243X1. Push .
2. Highlight [Home] and push .
IDE01373. The home location is displayed, and the
system sets the home location as the
destination.
4. Setting destination
4-11
Condition: Language=NAM_English/

Black plate (92,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
5. Route guidance
5-2
PROCEDURES AFTER SETTING DESTINA-
TION
After performing a route search, the route
guidance can be immediately started. Also,
it is possible to confirm or change a route.
IRG0085Available items after setting destination. [Start]:
Starts route guidance to the selected
destination.
“Starting route guidance”
(page 5-2)
. [More Routes]:
Displays 3 alternative routes.
“Selecting route” (page 5-3)
. [Add/Route Info]:
Displays the route information. A desti-
nation or a waypoint can also be
added.
“Confirming route” (page 5-3)
. [Move Location]:
Displays a map screen. The location of
the destination can be adjusted.
“Moving location of destination”
(page 5-5)
. [Store Location]:
Stores the location in the Address
Book.
“Storing location” (page 5-5)
. [Place Info]:
Displays information about the facility
that has been set as the destination, if
it is included in the map data.
“Viewing information about
searched location” (page 5-6)
INFO:
.
If no operations have been performed on the
system for several seconds, [Start] is auto-
matically selected, and the system starts
route guidance.
.When using waypoints, [More Routes] is
disabled. After the route is started, push
then select [Edit/Add to Route] to
change the route between each waypoint.
.The same screen as when [Move Location] is
selected can be displayed with the following
operations:
—Touching the map screen
—Pushing the directional buttons except
for the up/down button (INFINITI con-
troller with directional buttons)
—Pushing the slide switch except in the
upward/downward direction (INFINITI
controller without directional buttons)
STARTING ROUTE GUIDANCE
IRG00851. Highlight [Start] and push .
Route guidance starts.
Condition: Language=NAM_English/

Black plate (95,1)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
.If a destination was added, the prior
destination becomes a waypoint.
MOVING LOCATION OF DESTINATION
The location of the destination can be
adjusted by moving the cross pointer
across the map.
IRG00941.Highlight [Move Location] and push
.
INFO:
The screen for adjusting the location also
changes by touching the map screen dis-
played on the right side of the screen.
IRG00952. Adjust the location by moving the cross
pointer across the map and push
. The location of the destination
is modified.
INFO:
.
The map scale can be changed by turning
the center dial or touching the scale icon.
The map scale can also be changed by
pressing / (if so
equipped).
.The same screen as when [Move Location] is
touched can be displayed with the following
operations:
—Touching the map screen.
—Pushing the directional buttons except
up/down buttons (INFINITI controller
with directional buttons).
—Pushing the slide switch except upward/
downward (INFINITI controller without
directional buttons).
STORING LOCATION
A searched location can be stored in the
Address Book. Then it can be easily
retrieved and set as a destination (or
waypoint).
IRG00961. Highlight [Store Location] and push
.
IRG0097
5. Route guidance
5-5
Condition: Language=NAM_English/