wiring INFINITI M35 2006 Factory User Guide

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
Revision: 2006 January2006 M35/M45
AUTOMATIC TRANSMISSION
INDEX FOR DTC ........................................................ 5
Alphabetical Index .................................................... 5
DTC No. Index ......................................................... 6
PRECAUTIONS .......................................................... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine .................................................... 7
Precautions .............................................................. 8
Service Notice or Precautions .................................. 9
PREPARATION ......................................................... 10
Special Service Tools ............................................. 10
Commercial Service Tools ....................................... 11
A/T FLUID ................................................................. 12
Changing A/T Fluid .............................................
... 12
Checking A/T Fluid ................................................. 13
A/T Fluid Cooler Cleaning ...................................... 14
A/T CONTROL SYSTEM .......................................... 17
Cross-Sectional View (VQ35DE Models for 2WD) ... 17
Cross-Sectional View (VK45DE Models for 2WD) ... 18
Cross-Sectional View (AWD Models) ..................... 19
Shift Mechanism ..................................................... 20
TCM Function ......................................................... 31
CAN Communication .............................................. 32
Input/Output Signal of TCM .................................... 32
Line Pressure Control ............................................ 33
Shift Control ........................................................... 34
Lock-up Control ...................................................... 37
Engine Brake Control ............................................. 38
Control Valve .......................................................... 38
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 40
Introduction ............................................................ 40
OBD-II Function for A/T System ............................. 40
One or Two Trip Detection Logic of OBD-II ............ 40
OBD-II Diagnostic Trouble Code (DTC) ................. 40
Malfunction Indicator Lamp (MIL) ........................... 43
TROUBLE DIAGNOSIS ............................................ 44
DTC Inspection Priority Chart ................................ 44
Fail-safe ................................................................. 44How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 46
A/T Electrical Parts Location .................................. 51
Circuit Diagram ....................................................... 52
Inspections before Trouble Diagnosis .................... 53
Check before Engine Is Started .............................. 57
Check at Idle ........................................................... 57
Cruise Test - Part 1 ................................................. 59
Cruise Test - Part 2 ................................................. 61
Cruise Test - Part 3 ................................................. 62
Vehicle Speed at Which Gear Shifting Occurs ....... 63
Vehicle Speed at Which Lock-Up Occurs/Releases ... 63
Symptom Chart ....................................................... 64
TCM Input/Output Signal Reference Values ........... 89
CONSULT-II Function (A/T) .................................... 90
Diagnostic Procedure without CONSULT-II ..........103
DTC U1000 CAN COMMUNICATION LINE ............105
Description ............................................................105
On Board Diagnosis Logic ....................................105
Possible Cause .....................................................105
DTC Confirmation Procedure ...............................105
Wiring Diagram — AT — CAN ..............................106
Diagnostic Procedure ...........................................107
DTC P0615 START SIGNAL CIRCUIT ...................108
Description ............................................................108
CONSULT-II Reference Value ..............................108
On Board Diagnosis Logic ....................................108
Possible Cause .....................................................108
DTC Confirmation Procedure ...............................108
Wiring Diagram — AT — STSIG ..........................109
Diagnostic Procedure ...........................................110
DTC P0700 TCM .....................................................112
Description ............................................................112
On Board Diagnosis Logic ....................................112
Possible Cause .....................................................112
DTC Confirmation Procedure ...............................112
Diagnostic Procedure ...........................................112
DTC P0705 PARK/NEUTRAL POSITION SWITCH .113
Description ............................................................113
CONSULT-II Reference Value ..............................113

AT-2Revision: 2006 January2006 M35/M45 On Board Diagnosis Logic ....................................113
Possible Cause .....................................................113
DTC Confirmation Procedure ...............................113
Wiring Diagram — AT — PNP/SW .......................114
Diagnostic Procedure ...........................................115
DTC P0717 TURBINE REVOLUTION SENSOR ....117
Description ............................................................117
CONSULT-II Reference Value ..............................117
On Board Diagnosis Logic ....................................117
Possible Cause .....................................................117
DTC Confirmation Procedure ...............................117
Diagnostic Procedure ...........................................118
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) ...............................................119
Description ............................................................119
CONSULT-II Reference Value ..............................119
On Board Diagnosis Logic ....................................119
Possible Cause .....................................................119
DTC Confirmation Procedure ...............................119
Wiring Diagram — AT — VSSA/T .........................121
Diagnostic Procedure ...........................................122
DTC P0725 ENGINE SPEED SIGNAL ...................124
Description ............................................................124
CONSULT-II Reference Value ..............................124
On Board Diagnosis Logic ....................................124
Possible Cause .....................................................124
DTC Confirmation Procedure ...............................124
Diagnostic Procedure ...........................................125
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE .................................................126
Description ............................................................126
CONSULT-II Reference Value ..............................126
On Board Diagnosis Logic ....................................126
Possible Cause .....................................................126
DTC Confirmation Procedure ...............................126
Diagnostic Procedure ...........................................127
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) . 128
Description ............................................................128
CONSULT-II Reference Value ..............................128
On Board Diagnosis Logic ....................................128
Possible Cause .....................................................128
DTC Confirmation Procedure ...............................128
Diagnostic Procedure ...........................................129
DTC P0745 LINE PRESSURE SOLENOID VALVE .130
Description ............................................................130
CONSULT-II Reference Value ..............................130
On Board Diagnosis Logic ....................................130
Possible Cause .....................................................130
DTC Confirmation Procedure ...............................130
Diagnostic Procedure ...........................................131
DTC P1705 THROTTLE POSITION SENSOR .......132
Description ............................................................132
CONSULT-II Reference Value ..............................132
On Board Diagnosis Logic ....................................132
Possible Cause .....................................................132
DTC Confirmation Procedure ...............................132
Diagnostic Procedure ...........................................133
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ..................................................................135Description ............................................................135
CONSULT-II Reference Value ...............................135
On Board Diagnosis Logic ....................................135
Possible Cause .....................................................135
DTC Confirmation Procedure ................................135
Wiring Diagram — AT — FTS ...............................136
Diagnostic Procedure ............................................137
Component Inspection ..........................................139
DTC P1721 VEHICLE SPEED SENSOR MTR .......140
Description ............................................................140
CONSULT-II Reference Value ...............................140
On Board Diagnosis Logic ....................................140
Possible Cause .....................................................140
DTC Confirmation Procedure ................................140
Diagnostic Procedure ............................................141
DTC P1730 A/T INTERLOCK .................................142
Description ............................................................142
On Board Diagnosis Logic ....................................142
Possible Cause .....................................................142
DTC Confirmation Procedure ................................142
Judgement of A/T Interlock ...................................143
Diagnostic Procedure ............................................143
DTC P1731 A/T 1ST ENGINE BRAKING ...............145
Description ............................................................145
CONSULT-II Reference Value ...............................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ................................145
Diagnostic Procedure ............................................146
DTC P1752 INPUT CLUTCH SOLENOID VALVE ..147
Description ...................................................
.........147
CONSULT-II Reference Value ...............................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ................................147
Diagnostic Procedure ............................................148
DTC P1754 INPUT CLUTCH SOLENOID VALVE
FUNCTION ..............................................................149
Description ............................................................149
CONSULT-II Reference Value ...............................149
On Board Diagnosis Logic ....................................149
Possible Cause .....................................................149
DTC Confirmation Procedure ................................149
Diagnostic Procedure ............................................150
DTC P1757 FRONT BRAKE SOLENOID VALVE ...151
Description ............................................................151
CONSULT-II Reference Value ...............................151
On Board Diagnosis Logic ....................................151
Possible Cause .....................................................151
DTC Confirmation Procedure ................................151
Diagnostic Procedure ............................................152
DTC P1759 FRONT BRAKE SOLENOID VALVE
FUNCTION ..............................................................153
Description ............................................................153
CONSULT-II Reference Value ...............................153
On Board Diagnosis Logic ....................................153
Possible Cause .....................................................153
DTC Confirmation Procedure ................................153
Diagnostic Procedure ............................................154

AT-3
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 January2006 M35/M45 DTC P1762 DIRECT CLUTCH SOLENOID VALVE .155
Description ...........................................................155
CONSULT-II Reference Value ..............................155
On Board Diagnosis Logic ...................................155
Possible Cause ....................................................155
DTC Confirmation Procedure ...............................155
Diagnostic Procedure ...........................................156
DTC P1764 DIRECT CLUTCH SOLENOID VALVE
FUNCTION ..............................................................157
Description ...........................................................157
CONSULT-II Reference Value ..............................157
On Board Diagnosis Logic ...................................157
Possible Cause ....................................................157
DTC Confirmation Procedure ...............................157
Diagnostic Procedure ...........................................158
DTC P1767 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE .................................................159
Description ...........................................................159
CONSULT-II Reference Value ..............................159
On Board Diagnosis Logic ...................................159
Possible Cause ....................................................159
DTC Confirmation Procedure ...............................159
Diagnostic Procedure ...........................................160
DTC P1769 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE FUNCTION .............................161
Description ...........................................................161
CONSULT-II Reference Value ..............................161
On Board Diagnosis Logic ...................................161
Possible Cause ....................................................161
DTC Confirmation Procedure ...............................161
Diagnostic Procedure ...........................................162
DTC P1772 LOW COAST BRAKE SOLENOID
VALVE .....................................................................163
Description ...........................................................163
CONSULT-II Reference Value ..............................163
On Board Diagnosis Logic ...................................163
Possible Cause ....................................................163
DTC Confirmation Procedure ...............................163
Diagnostic Procedure ...........................................164
DTC P1774 LOW COAST BRAKE SOLENOID
VALVE FUNCTION .................................................165
Description ...........................................................165
CONSULT-II Reference Value ..............................165
On Board Diagnosis Logic ...................................165
Possible Cause ....................................................165
DTC Confirmation Procedure ...............................165
Diagnostic Procedure ..........................................
.166
DTC P1815 MANUAL MODE SWITCH ..................167
Description ...........................................................167
CONSULT-II Reference Value ..............................167
On Board Diagnosis Logic ...................................167
Possible Cause ....................................................167
DTC Confirmation Procedure ...............................167
Wiring Diagram — AT — MMSW .........................168
Diagnostic Procedure ...........................................170
Component Inspection .........................................171
DTC P1841 ATF PRESSURE SWITCH 1 ...............172
Description ...........................................................172
CONSULT-II Reference Value ..............................172On Board Diagnosis Logic ....................................172
Possible Cause .....................................................172
DTC Confirmation Procedure ...............................172
Diagnostic Procedure ...........................................173
DTC P1843 ATF PRESSURE SWITCH 3 ...............174
Description ............................................................174
CONSULT-II Reference Value ..............................174
On Board Diagnosis Logic ....................................174
Possible Cause .....................................................174
DTC Confirmation Procedure ...............................174
Diagnostic Procedure ...........................................175
DTC P1845 ATF PRESSURE SWITCH 5 ...............176
Description ............................................................176
CONSULT-II Reference Value ..............................176
On Board Diagnosis Logic ....................................176
Possible Cause .....................................................176
DTC Confirmation Procedure ...............................176
Diagnostic Procedure ...........................................177
DTC P1846 ATF PRESSURE SWITCH 6 ...............178
Description ............................................................178
CONSULT-II Reference Value ..............................178
On Board Diagnosis Logic ....................................178
Possible Cause .....................................................178
DTC Confirmation Procedure ...............................178
Diagnostic Procedure ...........................................179
MAIN POWER SUPPLY AND GROUND CIRCUIT .180
Wiring Diagram — AT — MAIN ............................180
Diagnostic Procedure ...........................................181
CLOSED THROTTLE POSITION AND WIDE OPEN
THROTTLE POSITION CIRCUIT ............................184
CONSULT-II Reference Value ..............................184
Diagnostic Procedure ...........................................184
BRAKE SIGNAL CIRCUIT ......................................185
CONSULT-II Reference Value ..............................185
Diagnostic Procedure ...........................................185
A/T INDICATOR CIRCUIT .......................................186
Description ............................................................186
CONSULT-II Reference Value ..............................186
Diagnostic Procedure ...........................................186
TROUBLE DIAGNOSIS FOR SYMPTOMS ............187
Wiring Diagram — AT — NONDTC ......................187
A/T CHECK Indicator Lamp Does Not Come On . 190
Engine Cannot Be Started in “P” or “N” Position ..190
In “P” Position, Vehicle Moves When Pushed ......191
In “N” Position, Vehicle Moves ..............................192
Large Shock (“N” to “D” Position) .........................193
Vehicle Does Not Creep Backward in “R” Position .195
Vehicle Does Not Creep Forward in “D” Position . 197
Vehicle Cannot Be Started from D
1 ......................199
A/T Does Not Shift: D
1 D2 ................................201
A/T Does Not Shift: D
2 D3 ................................203
A/T Does Not Shift: D
3 D4 ................................205
A/T Does Not Shift: D
4 D5 ................................207
A/T Does Not Lock-Up ..........................................209
A/T Does Not Hold Lock-Up Condition .................210
Lock-Up Is Not Released ......................................212
Engine Speed Does Not Return to Idle ................212
Cannot Be Changed to Manual Mode ..................213
A/T Does Not Shift: 5th Gear
4th Gear ............214

AT-4Revision: 2006 January2006 M35/M45 A/T Does Not Shift: 4th Gear
3rd Gear ............215
A/T Does Not Shift: 3rd Gear
2nd Gear ...........217
A/T Does Not Shift: 2nd Gear
1st Gear ............218
Vehicle Does Not Decelerate by Engine Brake ....220
SHIFT CONTROL SYSTEM ....................................222
Control Device Removal and Installation ..............222
Control Rod Removal and Installation ..................226
Adjustment of A/T Position ...................................227
Checking of A/T Position ......................................228
A/T SHIFT LOCK SYSTEM .....................................229
Description ............................................................229
Shift Lock System Electrical Parts Location .........229
Wiring Diagram — AT — SHIFT ...........................230
Diagnostic Procedure ...........................................232
ON-VEHICLE SERVICE ..........................................236
C o n t r o l V a l v e W i t h T C M a n d A / T F l u i d Te m p e r a t u r e
Sensor 2 ...............................................................236
Parking Components (2WD Models Only) ............248
Rear Oil Seal (VQ35DE Models Only) ..................260
Revolution Sensor Components (2WD Models
Only) .....................................................................261
AIR BREATHER HOSE ...........................................269
Removal and Installation ......................................269
TRANSMISSION ASSEMBLY ................................271
Removal and Installation (2WD Models) ..............271
Removal and Installation (AWD Models) ..............275
OVERHAUL .............................................................278
Components .........................................................278Oil Channel ...........................................................292
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................295
DISASSEMBLY .......................................................298
Disassembly ..........................................................298
REPAIR FOR COMPONENT PARTS ......................318
Oil Pump ...............................................................318
Front Sun Gear, 3rd One-Way Clutch ...................321
Front Carrier, Input Clutch, Rear Internal Gear .....323
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ..............................................329
High and Low Reverse Clutch ..............................335
Direct Clutch .........................................................337
ASSEMBLY .............................................................340
Assembly (1) .........................................................340
Adjustment ............................................................356
Assembly (2) .........................................................358
SERVICE DATA AND SPECIFICATIONS (SDS) ....365
General Specifications ......................................... .365
Vehicle Speed at Which Gear Shifting Occurs ......365
Vehicle Speed at Which Lock-Up Occurs/Releases .366
Stall Speed ............................................................366
Line Pressure ........................................................366
A/T Fluid Temperature Sensor ..............................366
Turbine Revolution Sensor ....................................367
Vehicle Speed Sensor A/T (Revolution Sensor) ...367
Reverse Brake ......................................................367
Total End Play .......................................................367

PRECAUTIONS
AT-7
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 January2006 M35/M45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NCS001JC
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NING :
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for On Board Diagnostic (OBD) System of A/T and EngineNCS001JD
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:
Be sure to turn the ignition switch OFF and disconnect the battery cable from the negative termi-
nal before any repair or inspection work. The open/short circuit of related switches, sensors, sole-
noid valves, etc. will cause the MIL to light up.
Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. may cause the MIL to light up due to a short circuit.
Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.
Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.

AT-32
A/T CONTROL SYSTEM
Revision: 2006 January2006 M35/M45
CAN CommunicationNCS001JQ
SYSTEM DESCRIPTION
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only. Refer to LAN-34, "
CAN
Communication Unit" .
Input/Output Signal of TCMNCS001JR
*1: Spare for vehicle speed sensorꞏA/T (revolution sensor)
*2: Spare for accelerator pedal position signal
*3: If these input and output signals are different, the TCM triggers the fail-safe function.
*4: Used as a condition for starting self-diagnostics; if self-diagnostics are not started, it is judged that there is some kind of error.
*5: Input by CAN communications.
*6: Output by CAN communications.Control itemLine
pressure
controlVehicle
speed
controlShift
controlLock-up
controlEngine
brake
controlFail-safe
function
(*3)Self-diag-
nostics
function
InputAccelerator pedal position signal
(*5)XXXXXXX
Vehicle speed sensor A/T
(revolution sensor)XXXXXXX
Vehicle speed sensor MTR
(*1) (*5)X
Closed throttle position signal
(*5)X(*2) X X X X(*4)
Wide open throttle position signal
(*5)XX(*4)
Turbine revolution sensor 1 X X X X X
Turbine revolution sensor 2
(for 4th speed only)X XXXX
Engine speed signals
(*5)XXXXXXX
Stop lamp switch signal
(*5)XXX X(*4)
A/T fluid temperature sensors 1, 2XXXX XX
ASCD or ICC
sensor inte-
grated unitOperation signal
(*5)XXX
Overdrive cancel
signal
(*5)X
Out-
putDirect clutch solenoid
(ATF pressure switch 5)XX XX
Input clutch solenoid
(ATF pressure switch 3)XX XX
High and low reverse clutch solenoid
(ATF pressure switch 6)XX XX
Front brake solenoid
(ATF pressure switch 1)XX XX
Low coast brake solenoid
(ATF pressure switch 2)XX XXX
Line pressure solenoidXXXXXXX
TCC solenoid X X X
Self-diagnostics table
(*6)X
Starter relayXX

AT-46
TROUBLE DIAGNOSIS
Revision: 2006 January2006 M35/M45
How to Perform Trouble Diagnosis for Quick and Accurate RepairNCS001K4
INTRODUCTION
The TCM receives a signal from the vehicle speed sensor, accelera-
tor pedal position sensor (throttle position sensor) or PNP switch and
provides shift control or lock-up control via A/T solenoid valves.
The TCM also communicates with the ECM by means of a signal
sent from sensing elements used with the OBD-related parts of the
A/T system for malfunction-diagnostic purposes. The TCM is capa-
ble of diagnosing malfunctioning parts while the ECM can store mal-
functions in its memory.
Input and output signals must always be correct and stable in the
operation of the A/T system. The A/T system must be in good oper-
ating condition and be free of valve seizure, solenoid valve malfunc-
tion, etc.
It is much more difficult to diagnose a error that occurs intermittently
rather than continuously. Most intermittent errors are caused by poor
electric connections or improper wiring. In this case, careful check-
ing of suspected circuits may help prevent the replacement of good
parts.
A visual check only may not find the cause of the errors. A road test
with CONSULT-II (or GST) or a circuit tester connected should be
performed. Follow the AT- 4 7 , "
WORK FLOW" .
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such errors, especially
intermittent ones. Find out what symptoms are present and under
what conditions they occur. A “DIAGNOSTIC WORKSHEET” as
shown on the example (Refer to AT- 4 8
) should be used.
Start your diagnosis by looking for “conventional” errors first. This will
help troubleshoot driveability errors on an electronically controlled
engine vehicle.
Also check related Service bulletins.
SAT631IB
SAT632I
SEF234G

DTC U1000 CAN COMMUNICATION LINE
AT-105
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 January2006 M35/M45
DTC U1000 CAN COMMUNICATION LINEPFP:23710
DescriptionNCS001KJ
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
On Board Diagnosis LogicNCS001KK
This is an OBD-II self-diagnostic item.
Diagnostic trouble code “U1000 CAN COMM CIRCUIT” with CONSULT-II or 17th judgement flicker with-
out CONSULT-II is detected when TCM cannot communicate to other control units.
Possible CauseNCS001KL
Harness or connectors
(CAN communication line is open or shorted.)
DTC Confirmation ProcedureNCS001KM
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON.
2. Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Start engine and wait for at least 6 seconds.
4. If DTC is detected, go to AT- 1 0 7 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-II”.
BCIA0030E

AT-106
DTC U1000 CAN COMMUNICATION LINE
Revision: 2006 January2006 M35/M45
Wiring Diagram — AT — CANNCS001KN
TCWT0342E

DTC P0615 START SIGNAL CIRCUIT
AT-109
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 January2006 M35/M45
Wiring Diagram — AT — STSIGNCS001KU
TCWT0343E