control INFINITI M35 2007 Factory Service Manual

GW-80
REAR WINDOW DEFOGGER
Revision: 2007 April2007 M35/M45
Terminal and Reference Value for BCMNIS0022M
Terminal and Reference Value for IPDM E/RNIS0022N
Te r m i -
nalWire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
38 W Ignition switch ON or START Input Ignition switch (ON or START position) Battery voltage
39 L CAN− HInput/
Output——
40 P CAN− LInput/
Output——
42 P Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
55 W Power source (Fusible link) Input — Battery voltage
Te r m i -
nalWire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
5 W Battery power supply Output — Battery voltage
6 R Battery power supply Output — Battery voltage
38 B Ground (Power) — — 0
49 L CAN− HInput/
Output——
50 P CAN− LInput/
Output——
51 B Ground (Signal) — — 0
57 GRear window defogger relay
control signalInputWhen rear window defogger switch is ON. 0
When rear window defogger switch is OFF. Battery voltage

GW-94
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
REVERSE INTERLOCK DOOR MIRROR SYSTEMPFP:28548
Component Parts and Harness Connector LocationNIS00230
System DescriptionNIS00231
Select one of the door mirror faces by change over switch, and then set the selected mirror face downward/
inward.
This operation is synchronized with the R position operation of A/T control device.
OPERATION CONDITIONS

Ignition switch : ON

Changeover switch : Select either left or right

A/T control device : R position
During the reverse interlock door mirror system, if all of the above conditions are not satisfied, mirror face
returns to original angle.
MIRROR UNGLE MEMORY FUNCTION

During the reverse interlock door mirror operation, the mirror angle can be changed. After adjustment, the
mirror face positions can be memorized (2 positions). For memory setting, Refer to SE-12, "
MEMORY
OPERATION"

Initial setting is downward 7°, inward 1° (both of left and right)
Power supplied at all times

through 50A fusible link (letter F, located in the fuse block and fusible link)

to automatic drive positioner control unit terminal 39 and

to driver seat control unit terminal 33.
PIIB6099E
1. Fuse block (J/B) 2. Fusible link 3.Door mirror remote control switch
M95
4. TCM (A/T assembly) F42 5.Automatic drive positioner control
unit M6, M7 (view with the instra-
ment lower panel LH removed)6. Driver seat control unit B204, B205

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-95
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45

through 10A fuse [No.21, located in the fuse block (J/B)]

to automatic drive positioner control unit terminal 34 and

to driver seat control unit terminal 40.
Ground is supplied

to automatic drive positioner control unit terminals 40 and 48.

through body grounds M16 and M70.

to driver seat control unit terminals 32 and 48.

through body grounds B5, B40 and B131.

to door mirror remote control switch terminal 13

through body grounds M16 and M70.
REVERSE INTERLOCK DOOR MIRROR SYSTEM OPERATION

When the ignition switch is in ON position, A/T control device into R position. Then TCM (in A/T assembly)
detects it and sends the A/T shift position signal to the driver seat control unit via DATA LINE (CAN H,
CAN L).

When selecting either left and right changeover switch, the automatic drive position control unit judges
which door mirror is selected according to the voltage of terminals 2 and 18. And then, it sends the signal
to driver seat control unit via communication signal.

When the driver seat control unit receives the A/T shift position signal and changeover switch signal, it
sends the operation signal to the automatic drive positioner control unit using the communication signal so
that the each mirror sensor voltage stays in a specified value.

Door mirror (RH) selected
Supply the power from terminals 14, 15 and 30 to door mirror (RH) terminals 5, 6 and 7 so that the voltage
of terminals 5 and 21 stays in a specified value. Then, adjust the mirror angle.

Door mirror (LH) selected
Supply the power from terminals 16, 31 and 32 to door mirror (LH) terminals 5, 6 and 7 do that the voltage
of terminals 6 and 22 is the specified value. Then, adjust the mirror angle.
CAN Communication System DescriptionNIS00232
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNIS00233
Refer to LAN-50, "CAN System Specification Chart"

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-103
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
Terminals and Reference Values for Automatic Drive Positioner Control UnitNIS00236
Te r -
minalWire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
2VChangeover switch
RH signalInputWhen changeover
switch positionRH 0
Other than above 5
3GMirror switch
UP signalInputWhen mirror switch
positionUP 0
Other than above 5
4WMirror switch
LEFT signalInputWhen mirror switch
positionLEFT 0
Other than above 5
5L/RDoor mirror RH sensor
vertical signalInputWhen door mirror
RH mirror face posi-
tionClose to perk 4.2
Close to valley 0.5
6LGDoor mirror LH sensor
vertical signalInputWhen door mirror LH
mirror face positionClose to perk 4.2
Close to valley 0.5
10 O UART LINE (TX)Input/
OutputTilt switch operated
14 LDoor mirror RH mirror
motor
UP signalOutputWhen door mirror
RH mirror motor
operationUP Battery voltage
Other than above 0
15 GDoor mirror RH mirror
motor LEFT signalOutputWhen door mirror
RH mirror motor
operationLEFT Battery voltage
Other than above 0
16 W/LDoor mirror LH mirror
motor RIGHT or DOWN
signalOutputWhen door mirror LH
mirror motor opera-
tionRIGHT or DOWN Battery voltage
Other than above 0
18 OChangeover switch
LH signalInputWhen changeover
switch positionLH 0
Other than above 5
19 L Mirror switch DOWN signal InputWhen mirror switch
positionDOWN 0
Other than above 5
20 BR Mirror switch RIGHT signal inputWhen mirror switch
positionRIGHT 0
Other than above 5
21 SBDoor mirror RH sensor
horizontal signalInputWhen door mirror
RH mirror face posi-
tionClose to left edge 3.5
Close to right edge 0.5
22 O/LDoor mirror LH sensor
horizontal signalInputWhen door mirror LH
mirror face positionClose to left edge 0.5
Close to right edge 3.5
26 P UART LINE (RX)Input/
OutputTilt switch operated
30 GRDoor mirror LH mirror
motor RIGHT or DOWN
signalOutputWhen door mirror LH
mirror motor opera-
tionRIGHT or DOWN Battery voltage
Other than above 0
SKIA0175E
SKIA0175E

GW-104
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
Terminals and Reference Values for Driver Seat Control UnitNIS00237
31 BRDoor mirror LH mirror
motor UP signalOutputWhen door mirror LH
mirror motor opera-
tionUP Battery voltage
Other than above 0
32 VDoor mirror LH mirror
motor LEFT signalOutputWhen door mirror LH
mirror motor opera-
tionLEFT Battery voltage
Other than above 0
33 W Mirror sensor power supply Output — Battery voltage
34 R Power supply (fuse) Input — Battery voltage
39 L Power supply (fusible link) Input — Battery voltage
40 B Ground (signal) — — 0
41 Y Sensor ground — — 0
48 B Ground (power) — — 0 Te r -
minalWire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
Te r m i -
nal Wire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
1 R/G UART LINE (RX)Input/
OutputTilt switch operated
3 L CAN-HInput/
Output——
17 W/R UART LINE (TX)Input/
OutputTilt switch operated
19 P CAN-LInput/
Output——
32 B/W Ground (signal) — — 0
33 W Power supply (fusible link) Input — Battery voltage
40 B/W Power supply (fuse) Input — Battery voltage
48 B/W Ground (power) — — 0
SKIA0175E
SKIA0175E

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-105
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
CONSULT-II Function (AUTO DRIVE POS.)NIS00238
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
*1: For setting automatic drive positioner functions only.
*2: During vehicle driving, do not perform active test.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure"
DATA MONITOR
Selection from Menu
ACTIVE TEST
CAUTION:
During vehicle driving, do not perform active test.
NOTE:
If active test is performed, reset seat memory and key fob interlock drive positioner after performing work.
CONSULT-II
diagnosis
itemsInspection item, self-diagnosis mode Content Refer to page
AUTO DRIVE
POSITIONERWORK SUPPORT*
1Changes the setting for each function.SE-39
SELF–DIG RESULTS Check the self-diagnosis results.SE-37
DATA MONITOR Selection from menuDisplays the input data to driver seat control
unit and automatic driving positioned control
unit on real-time basis.SE-38
CAN DIAGNOSTIC SUPPORT MONITORThe results of transmit / receive diagnosis of
CAN communication can be readLAN-13
ACTIVE TEST*2Gives a drive signal to a load to check the
operation.SE-39
DRIVER SEAT CONTROL UNIT PART NUMBER Displays driver seat control unit part No. —
Monitor item [OPERATION or UNIT] Contents
MIR CON SW–UP “ON/OFF”ON/OFF status judged from the door mirror remote control switch (UP) signal is
displayed.
MIR CON SW–DN “ON/OFF”ON/OFF status judged from the door mirror remote control switch (DOWN) signal
is displayed.
MIR CON SW–RH “ON/OFF”ON/OFF status judged from the door mirror remote control switch (RIGHT) signal
is displayed.
MIR CON SW–LH “ON/OFF”ON/OFF status judged from the door mirror remote control switch (LEFT) signal s
displayed.
MIR CHNG SW–R “ON/OFF”ON/OFF status judged from the door mirror remote control switch (switching to
RIGHT) signal is displayed.
MIR CHNG SW–L “ON/OFF”ON/OFF status judged from the door mirror remote control switch (switching to
LEFT) signal is displayed.
SET SW “ON/OFF” ON/OFF status judged from the setting switch signal is displayed.
MEMORY SW1 “ON/OFF” ON/OFF status judged from the seat memory switch 1 signal is displayed.
MEMORY SW2 “ON/OFF” ON/OFF status judged from the seat memory switch 2 signal is displayed.
MIR/SE RH R–L “V” Voltage output from RH door mirror sensor (LH/RH) is displayed.
MIR/SE RH U–D “V” Voltage output from RH door mirror sensor (UP/DOWN) is displayed.
MIR/SE LH R–L “V” Voltage output from LH door mirror sensor (LH/RH) is displayed.
MIR/SE LH U–D “V” Voltage output from LH door mirror sensor (UP/DOWN) is displayed.

GW-106
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
Display Item List
Work Flow NIS00239
1. Check the symptom and customer's requests.
2. Understand the system description. Refer to GW-94, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to GW-106,
"Symptom Chart"
4. Does reverse interlock door mirror system operate normally?
Yes , GO TO 5.
No, GO TO 3.
5. INSPECTION END
Symptom ChartNIS0023A
Test item Description
MIRROR MOTOR RHThe RH mirror motor moves the mirror UP/DOWN and LEFT/RIGHT by receiving the drive
signal.
MIRROR MOTOR LHThe LH mirror motor moves the mirror UP/DOWN and LEFT/RIGHT by receiving the drive
signal.
Symptom Diagnoses / service procedureReference
page
Reverse interlock door mirror does not operate.1. Check seat set switch circuitSE-81
2. Check changeover switch circuitGW-107
3. Check mirror switch circuitGW-109
4. Check A/T control device R position signal circuitGW-117
5. Check mirror motor circuitG W - 111
6. Check mirror sensor circuitGW-114
7. Replace automatic drive positioner control unitSE-11

At reverse interlock door mirror system operation, mirror
angle is not in the setting position

After finishing the reverse interlock door mirror system.
Operation, mirror angle does not return to the original posi-
tion1. Check mirror sensor circuitGW-1142. Check A/T control device R position signal circuitGW-117
3. Replace automatic drive positioner control unitSE-11
None of the door mirror can be operated using mirror switch. Check mirror switch circuitGW-109
A part of the remote control door mirror does not operated.1. Check mirror switch circuitGW-1092. Check door mirror circuitGW-109
Mirror remote control switch can not be switched right and left.1. Check changeover switch circuitGW-1072. Check mirror switch circuitGW-109

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-107
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
Check Changeover Switch CircuitNIS0023B
1. CHECK CHANGEOVER SWITCH SIGNAL
With CONSULT-II
Check the operation on (MIR CHNG SW-R” or “MIR CHNG SW-L) in the DATA MONITOR.
Without CONSULT-II
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit connector and ground.
OK
orNG
OK >> Changeover switch circuit is OK.
NG >> GO TO 2.
Monitor item
[OPERATION or UNIT]Contents
MIR CHNG SW–R“ON/
OFF”ON/OFF status judged from the changeover
switch (switching to RIGHT) signal is displayed.
MIR CHNG SW–L“ON/
OFF”ON/OFF status judged from the changeover
switch (switching to LEFT) signal is displayed.
PIIA0191E
Terminals
Change over switch
conditionVoltage (V)
(Approx.) (+)
(-) Automatic
drive posi-
tioner con-
trol unit
connectorTerminal
M62
GroundRIGHT 0
Other than above 5
18LEFT 0
Other than above 5
PIIB6015E

GW-108
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mirror remote control switch connector.
3. Check continuity between automatic drive positioner control unit connector and door mirror remote control
switch connector.
4. Check continuity between automatic drive positioner control unit
connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK CANGEOVER SWITCH
Check door mirror remote control switch.
OK or NG
OK >> GO TO 4.
NG >> Replace door mirror remote control switch.
4. CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirror remote control switch connector and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace harness.
AB
Continuity Automatic
drive posi-
tioner control
unit connectorTerminalDoor mirror
remote control
switch
connectorTerminal
M62
M953
Ye s
18 2
A
GroundContinuity
Automatic drive
positioner control
unit connectorTerminal
No
M62
18
PIIB6016E
Terminal
Change over switch
conditionContinuity
Door mirror remote control switch
2
13LEFT Yes
Other than above No
3RIGHT Yes
Other than above No
PIIB6017E
Door mirror remote
control switch connectorTerminal
GroundContinuity
M95 13 Yes
PIIB6018E

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-109
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
5. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit connector.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK >> Check the condition of harness and connector.
NG >> Replace automatic drive positioner control unit.
Check Mirror Switch Circuit NIS0023C
1. CHECK MIRROR SWITCH SIGNAL
With CONSULT-II
Check the operation on “(MIR CON SW–UP/DN) and (MIR CON SW–RH/LH) in the DATA MONITOR.
Without CONSULT-II
1. Turn ignition switch to ON position.
2. Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK >> Mirror switch circuit is OK.
NG >> GO TO 2.
Terminals
Voltage (V)
(Approx.) (+)
(-) Automatic drive
positioner control
unit connectorTerminal
M62
Ground 5
18
PIIB6015E
Monitor item
[OPERATION or UNIT]Contents
MIR CON SW–UP“ON/
OFF”ON/OFF status judged from the mirror switch
(UP) signal is displayed.
MIR CON SW–DN“ON/
OFF”ON/OFF status judged from the mirror switch
(DOWN) signal is displayed.
MIR CON SW–RH“ON/
OFF”ON/OFF status judged from the mirror switch
(RIGHT) signal is displayed.
MIR CON SW–LH“ON/
OFF”ON/OFF status judged from the mirror switch
(LEFT) signal s displayed.
PIIA0199E
Te r m i n a l s
Mirror switch
ConditionVoltage (V)
(Approx.) (+)
(–) Automatic drive
positioner control
unit connectorTerminal
M63
GroundUP 0
Other than above 5
4LEFT 0
Other than above 5
19DOWN 0
Other than above 5
20RIGHT 0
Other than above 5
PIIB6019E