steering wheel INFINITI M35 2007 Factory Service Manual

TROUBLE DIAGNOSIS
STC-29
[RAS]
C
D
E
F
H
I
J
K
L
MA
B
STC
Revision: 2007 April2007 M35/M45
How to Erase Self-Diagnostic Results
1. Perform applicable inspection of malfunctioning item and then repair or replace.
2. Start engine, and touch “START (NISSAN BASED VHCL)” “RAS/HICAS” “SELF-DIAG RESULTS” and
“ERASE” in this order to erase the diagnostic memory.
CAUTION:
If memory cannot be erased, repeat step 1, 2.
3. Perform self-diagnosis again, and make sure that DTC memory is erased.
C1910 MOTOR OUTPUT [MOTOR LOCK]When 17 A or more current flows to
the motor, the rear wheel steering
angle sensor signal does not
change for some time.STC-37
C1919 VEHICLE SPEED SEN [NO SIGNAL]No vehicle speed signal is input for
some time.STC-38
C1900 CONTROL UNIT [ABNORMAL1]
Control unit malfunctionSTC-35
C1901 CONTROL UNIT [ABNORMAL2]
C1905 CONTROL UNIT [ABNORMAL3]
C1906 CONTROL UNIT [ABNORMAL5]
C1907 CONTROL UNIT [ABNORMAL4]
C1908 CONTROL UNIT [ABNORMAL7]
C1909 CONTROL UNIT [ABNORMAL6]
C1922 CONTROL UNIT [ABNORMAL8]
C1927 CONTROL UNIT [ABNORMAL5]
C1928 CONTROL UNIT [ABNORMAL9]
C1920 STEERING ANGLE SEN [NO SIGNAL]No steering angle signal is input for
some time.STC-39
C1926 STEERING ANGLE SEN

An unexpected signal is input.

Steering angle sensor outputs the
malfunction signal.STC-39
C1929 VDCABS actuator and electric unit (con-
trol unit) outputs the malfunction
signal.STC-43
U1000 CAN COMM CIRCUITWhen a RAS control unit is not
transmitting or receiving CAN com-
munication signal 2 seconds or
more.STC-44
U1010 CONTROL UNIT (CAN)When detecting error during the ini-
tial diagnosis of CAN controller of
RAS control unit.STC-44
DTC Diagnostic item Diagnostic item is detected when... Check items

STC-30
[RAS]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
DATA MONITOR MODE
Operation Procedure
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. Touch “DATA MONITOR”.
3. Select from “SELECT MONITOR ITEM”, screen of data monitor is displayed.
NOTE:
When malfunction is detected, CONSULT-II performs REAL-TIME DIAGNOSIS. Also, any malfunction
detected while in this mode will be displayed in real time.
Display Item List
ACTIVE TEST MODE
Operation Procedure
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. When turning the steering wheel right or left, the rear wheel turns in the same direction. If the steering
wheel is not turned, the rear wheel turns left and right 5 times.
RAS CONTROL UNIT PART NUMBER
1. Perform “CONSULT-II Start Procedure”. Refer to GI-38, "CONSULT-II Start Procedure" .
2. The part number described on RAS control unit sticker is displayed.
Item [Display or Unit] Remarks
VHCL SPEED SE [km/h] or [mph] Vehicle speed received via CAN communication is displayed.
STEERING ANG [°] Steering angle received via CAN communication is displayed.
ENGINE SPEED [rpm] Engine speed received via CAN communication is displayed.
POWER STR SOL [A]Power steering solenoid controlling current that RAS control unit
outputs is displayed.
RR ST ANG-MAI [V]Rear wheel steering angle main sensor output voltage is dis-
played.
RR ST ANG-SUB [V] Rear wheel steering angle sub sensor output voltage is displayed.
RR ST ANG VOL [V]Voltage supplied from RAS control unit to rear wheel steering
angle sensor is displayed.
C/U VOLTAGE [V] Voltage supplied to RAS control unit is displayed.
MOTOR VOLTAGE [V] Voltage supplied from RAS control unit to RAS motor is displayed.
MOTOR CURRENT [A]RAS motor relay controlling current that RAS control unit outputs
is displayed.
MOTOR CRNT OPE [A] Current commanded value to RAS motor is displayed.
RR ANG OPE [°]Angle commanded value to rear wheel steering angle sensor is
displayed.
STOP LAMP SW [ON/OFF] Condition of stop lamp switch ON/OFF is displayed.
HICAS RELAY [ON/OFF] RAS motor relay ON/OFF condition is displayed.
FAILSAFE [ON/OFF] Fail-safe ON/OFF condition is displayed.
WARNING LAMP [ON/OFF] RAS warning lamp operating condition is displayed.
STEERING ANG RR ST ANG MAI RR ST ANG SUB MOTOR CURRENT
0° (Neutral) 2.4 V 2.4 V No output (Approx. 0 A)
R 90°Approx. 4.4 V Approx. 4.4 V
Output (change)
L 90°Approx. 0.4 V Approx. 0.4 V

TROUBLE DIAGNOSIS
STC-31
[RAS]
C
D
E
F
H
I
J
K
L
MA
B
STC
Revision: 2007 April2007 M35/M45
Diagnosis Procedure with Self-Diagnosis Function (Without CONSULT-II)NGS000EL
DESCRIPTION
If a malfunction is detected in the system, the RAS warning lamp turns on and indicates the malfunction. At
that time, fail-safe activates, and then stops the function.
SELF-DIAGNOSIS PROCEDURE
1. Start engine.
2. Turn steering wheel left and right at 20° or more and 5 times or more within 10 seconds. And then depress
the service brake 5 times or more.
3. RAS warning lamp blinks (displays normal/malfunction).
SELF-DIAGNOSIS DISPLAY
RAS warning lamp blinks and displays the self-diagnostic results.

Only DTCs are displayed as the pattern shown in the figure, and
then repeat the display.

If all items are normal, RAS warning lamp blinks at 4 Hz cycle.
SELF-DIAGNOSIS DISPLAY ITEMS
HOW TO ERASE SELF-DIAGNOSIS
If there is the history data for when the fail-safe has activated in the past, erase the memory with CONSULT-II.
Refer to STC-29, "
How to Erase Self-Diagnostic Results" .
CAN CommunicationNGS000EM
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only. Refer to LAN-50, "
CAN Sys-
tem Specification Chart" .
SGIA1243E
DTC (warning lamp blinks) Diagnosis item Inspection item
11 RAS control unitSTC-35, "
Inspection 1: RAS Control Unit Malfunction"
12 Motor power supplySTC-35, "Inspection 2: Motor Power Supply System"
13 Motor outputSTC-37, "Inspection 3: RAS Motor Output Malfunction"
21 Vehicle speed signalSTC-38, "Inspection 4: Vehicle Speed Signal"
22 Steering angle signalSTC-39, "Inspection 5: Steering Angle Signal Malfunction"
24 Rear wheel steering angle (main)STC-40, "Inspection 6: Rear Main Signal and Rear Sub Signal
Malfunction"
25 Rear wheel steering angle (sub)STC-40, "Inspection 6: Rear Main Signal and Rear Sub Signal
Malfunction"
26 VDCSTC-43, "Inspection 7: VDC Malfunction"
33 Engine speed signalSTC-44, "Inspection 8: Engine Speed Signal Malfunction"

STC-32
[RAS]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
For Fast and Accurate Trouble DiagnosisNGS000EN
Check the following items with the vehicle stopped

Is air pressure and size of tires proper?

Is the specified part used for the steering wheel?

Is control unit a genuine part?

Are there any fluid leakage from steering gear assembly, power steering oil pump, and hydraulic pipes,
etc? Refer to PS-8, "
Checking Fluid Leakage" .

Is the fluid level proper? Refer to PS-8, "Checking Fluid Level" .

Is the wheel alignment is adjusted properly? Refer to FSU-6, "Wheel Alignment Inspection" (2WD), FSU-
24, "Wheel Alignment Inspection" (AWD).

Are there any damage or modification to suspension or body resulting in increased weight or altered
ground clearance?

Check each link installation condition of suspension and axle.

Is the battery voltage proper?

Check each connector connection condition.
Check the following items while driving the vehicle

Conditions when the error occurred (5W 1H).

Is the engine is normal?
Basic InspectionNGS000EO
BASIC INSPECTION 1: POWER SUPPLY CIRCUIT TERMINAL LOOSENESS AND BATTERY
Check battery terminals for looseness on both positive and negative ones and ground connection. Also make
sure that battery voltage does not drop.
BASIC INSPECTION 2: RAS WARNING LAMP INSPECTION
1. Make sure RAS warning lamp turns on when ignition switch is turned ON.

If it does not turn on, refer to STC-33, "Trouble Diagnosis Chart" .
2. Make sure that RAS warning lamp turns off when the engine is started after ignition switch is turned ON. If
it does not turn off, perform self-diagnosis. Refer to STC-28, "
SELF-DIAG RESULT MODE" .
3. Always erase DTC memory after completing self-diagnosis. Refer to STC-29, "
How to Erase Self-Diag-
nostic Results" .
BASIC INSPECTION 3: RAS CONTROL UNIT POWER SUPPLY CIRCUIT AND GROUND CIR-
CUIT INSPECTION
1. CHECK RAS CONTROL UNIT CONNECTOR
Turn ignition switch OFF, disconnect RAS control unit harness connector, and check terminal for deformation,
disconnection, looseness, etc.
OK or NG
OK >> GO TO 2.
NG >> Poor connection of connector terminal. Repair or replace the terminal.
2. CHECK RAS CONTROL UNIT GROUND CIRCUIT
1. Disconnect RAS control unit harness connector B476, and then
check continuity between RAS control unit harness connector
B476 and ground.
OK or NG
OK >> GO TO 3.
NG >> Ground circuit open or shorted. Repair or replace any
inoperative parts. Terminal 34 – Ground : Continuity should exit.
SGIA1244E

STC-34
[RAS]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
DIAGNOSIS CHART BY SYMPTOM
24 Rear wheel steering angle (main)RR ST ANGLE SENSOR [MAIN SIGNAL] [C1915]
STC-40RR ST ANGLE SENSOR [ABNORMAL VOL] [C1914]
RR ST ANGLE SENSOR [OFFSET SIG1] [C1917]
RR ST ANGLE SENSOR [OFFSET SIG2] [C1918]
25 Rear wheel steering angle (sub)RR ST ANGLE SENSOR [SUB SIGNAL] [C1916]
RR ST ANGLE SENSOR [ABNORMAL VOL] [C1914]
RR ST ANGLE SENSOR [OFFSET SIG1] [C1917]
RR ST ANGLE SENSOR [OFFSET SIG2] [C1918]
26 VDC VDC [C1929]STC-43
33 Engine speed signal MOTOR OUTPUT [C1921]STC-44
— CAN COMM CIRCUIT [U1000]
STC-44
— CONTROL UNIT (CAN) [U1010]
Symptom Reference
It is not entering the self-diagnosis mode.STC-32, "
BASIC INSPECTION 3: RAS CONTROL UNIT POWER
SUPPLY CIRCUIT AND GROUND CIRCUIT INSPECTION"
STC-45, "Inspection 10: Stop Lamp Switch Harness"
STC-46, "Inspection 11: RAS Warning Lamp Harness"
RAS warning lamp does not turn on with ignition switch ON.STC-32, "
BASIC INSPECTION 3: RAS CONTROL UNIT POWER
SUPPLY CIRCUIT AND GROUND CIRCUIT INSPECTION"
STC-46, "Inspection 11: RAS Warning Lamp Harness"
RAS warning lamp turns on with ignition switch ON. It does not
turn off even if the engine is started.STC-32, "
Basic Inspection"

STC-28, "SELF-DIAG RESULT MODE"

STC-31, "Diagnosis Procedure with Self-Diagnosis Function
(Without CONSULT-II)"
RAS warning lamp may turn on after the engine is started.STC-28, "SELF-DIAG RESULT MODE"
The steering force does not change smoothly according to the
vehicle speed.STC-47, "Diagnosis Chart by Symptom 2"
Noise

STC-28, "SELF-DIAG RESULT MODE"

STC-31, "Diagnosis Procedure with Self-Diagnosis Function
(Without CONSULT-II)"
STC-14, "INSPECTION AFTER DISASSEMBLY"
Malfunction other than aboveSTC-47, "Diagnosis Chart by Symptom 1"

STC-40
[RAS]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
4. DATA MONITOR
1. Connect steering angle sensor harness connector.
2. Select “DATA MONITOR” on “STEERING ANG” mode, and then check the steering angle.
OK or NG
OK >> RAS control unit malfunction. Replace RAS control unit.
NG >> Replace steering angle sensor and adjust neutral position of steering angle sensor. Refer to BRC-
6, "Adjustment of Steering Angle Sensor Neutral Position" .
Inspection 6: Rear Main Signal and Rear Sub Signal MalfunctionNGS000EV
1. CHECK RAS CONTROL UNIT CONNECTOR
1. Turn ignition switch OFF, disconnect RAS control unit harness connector and rear wheel steering angle
sensor harness connector, and check terminal for deformation, disconnection, looseness, etc.
2. Reconnect harness connector securely, and perform self-diagnosis.
With CONSULT-II
Without CONSULT-II
Is above displayed on self-diagnosis display?
YES >> GO TO 2.
NO >> Connector terminal connection is loose, damaged, open, or shorted. Repair or replace the termi-
nal.
Steering condition DATA MONITOR
Straight-ahead position – 3.5 - +3.5°
Turn wheel to the right by 90°Approx. R 90°
Turn wheel to the left by 90°Approx. R 90°
Self-diagnosis results
RR ST ANGLE SENSOR [MAIN SIGNAL] [C1915]
RR ST ANGLE SENSOR [SUB SIGNAL] [C1916]
RR ST ANGLE SENSOR [OFFSET SIG1] [C1917]
RR ST ANGLE SENSOR [OFFSET SIG2] [C1918]
RR ST ANGLE SENSOR [ABNORMAL VOL] [C1914]
DTC (warning lamp blinks)
24
25

TROUBLE DIAGNOSIS
STC-41
[RAS]
C
D
E
F
H
I
J
K
L
MA
B
STC
Revision: 2007 April2007 M35/M45
2. CHECK (1): REAR WHEEL STEERING ANGLE SENSOR POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF, and disconnect rear wheel steering angle sensor harness connector B465.
2. Check continuity rear wheel steering angle sensor harness con-
nector B465 and ground.
3. Turn ignition switch ON, and then check voltage rear wheel
steering angle sensor harness connector B465 and ground.
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
3. CHECK (2): REAR WHEEL STEERING ANGLE SENSOR POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF, disconnect rear wheel steering angle sensor harness connector B465 and RAS
control unit harness connector B476.
2. Check continuity each harness connector of rear wheel steering
angle sensor harness connector B465 (A) and RAS control unit
harness connector B476 (B).
OK or NG
OK >> RAS control unit malfunction. Replace RAS control unit.
NG >> Harness between rear wheel steering angle sensor and
RAS control unit open or shorted. Repair or replace har-
ness. Terminal 3 − Ground : Continuity should exist.
SGIA1272E
Terminal 1 − Ground : Approx. 5 V
SGIA1273E
Rear wheel steering angle sensor RAS control unit Continuity
Terminal 1 Terminal 5 Yes
Terminal 3 Terminal 15 Yes
SGIA1650E

STC-42
[RAS]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
4. CHECK REAR WHEEL STEERING ANGLE SENSOR OUTPUT SIGNAL
1. Connect rear wheel steering angle sensor harness connector B465.
2. Check voltage RAS control unit harness connector B476 when
starting the engine and turning the steering wheel from neutral
position clockwise/counterclockwise by 180°.
CAUTION:
There is approximately 1 V or more difference between main output and sub output at straight-ahead position, inspection
results are “NG”.
OK or NG
OK >> RAS control unit malfunction. Replace RAS control unit.
NG >> GO TO 5.
5. CHECK REAR WHEEL STEERING ANGLE SENSOR OUTPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF, disconnect rear wheel steering angle sensor harness connector B465 and RAS
control unit harness connector B476.
2. Check continuity between each harness connector of rear wheel
steering angle sensor harness connector B465 (A) and RAS
control unit harness connector B476 (B).
OK or NG
OK >> Rear wheel steering angle sensor malfunction. Replace
rear wheel steering angle sensor.
NG >> Harness between rear wheel steering angle sensor and
RAS control unit open or shorted. Repair or replace harness.
SGIA1275E
Steering conditionRear wheel steering angle sensor
Rear main output
Terminal 4 (+) - 15 (-)Rear sub output
Terminal 7 (+) - 15 (-)
Straight-ahead (neutral position) Approx. 2.4 V Approx. 2.4 V
Turn wheel to the right by 180°Approx. 4.4 V Approx. 4.4 V
Turn wheel to the left by 180°Approx. 0.4 V Approx. 0.4 V
Rear wheel steering angle sensor RAS control unit Continuity
Terminal 2 Terminal 7 Yes
Terminal 4 Terminal 4 Yes
SGIA1651E

TROUBLE DIAGNOSIS
STC-43
[RAS]
C
D
E
F
H
I
J
K
L
MA
B
STC
Revision: 2007 April2007 M35/M45
Inspection 7: VDC MalfunctionNGS000EW
1. CHECK RAS CONTROL UNIT CONNECTOR
1. Turn ignition switch OFF, disconnect RAS control unit harness connector and rear wheel steering angle
sensor harness connector, and check terminal for deformation, disconnection, looseness, etc.
2. Reconnect harness connector securely, and perform self-diagnosis.
With CONSULT-II
Without CONSULT-II
Is above displayed on self-diagnosis display?
YES >> GO TO 2.
NO >> Connector terminal connection is loose, damaged, open, or shorted. Repair or replace the termi-
nal.
2. CHECK SELF-DIAGNOSTIC RESULTS
Perform VDC self-diagnosis. Refer to BRC-24, "
Self-Diagnosis" .
OK or NG
OK >> RAS control unit malfunction. Replace RAS control unit.
NG >> Repair or replace indicated part. After that, perform RAS self-diagnosis again to make sure that
there is no malfunction.
Self-diagnosis results
VDC [C1929]
DTC (warning lamp blinks)
26

STC-44
[RAS]
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
Inspection 8: Engine Speed Signal MalfunctionNGS000EX
1. CHECK SPEEDOMETER
Start the engine, and then check the combination meter (tachometer) operation.
Does it operate normally?
YES >> GO TO 2.
NO >> Combination meter. Refer to DI-5, "
COMBINATION METERS" .
2. CHECK RAS CONTROL UNIT CONNECTOR
1. Turn ignition switch OFF, disconnect RAS control unit harness connector, and check terminal for deforma-
tion, disconnection, looseness, etc.
2. Reconnect harness connector securely, and perform self-diagnosis.
With CONSULT-II
Without CONSULT-II
Is above displayed on self-diagnosis display?
YES >> RAS control unit malfunction. Replace RAS control unit.
NO >> Connector terminal connection is loose, damaged, open, or shorted. Repair or replace the termi-
nal.
Inspection 9: CAN Communication System MalfunctionNGS000EY
1. CHECK RAS CONTROL UNIT CONNECTOR
1. Turn ignition switch OFF, disconnect RAS control unit harness connector and rear wheel steering angle
sensor harness connector, and check terminal for deformation, disconnection, looseness, etc.
2. Reconnect harness connector securely, and perform CONSULT-II self-diagnosis.
Is above displayed on self-diagnosis display?
YES >>
If “CAN COMM [U1000]” is displayed, print out self–diagnosis. And then, GO TO LAN-50, "CAN
System Specification Chart" .

Replace RAS control unit if “CONTROL UNIT [CAN] [U1010]” is displayed.
NO >> Connector terminal connection is loose, damaged, open, or shorted. Repair or replace the termi-
nal.
Self-diagnostic results
MOTOR OUTPUT [C1921]
DTC (warning lamp blinks)
33
Self-diagnostic results
CAN COMM CIRCUIT [U1000]
CONTROL UNIT (CAN) [U1010]