sensor INFINITI M35 2007 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2007, Model line: M35, Model: INFINITI M35 2007Pages: 4647, PDF Size: 93.69 MB
Page 531 of 4647
ATC-80
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
SYSTEM DESCRIPTION
Component Parts
Upper ventilator door control system components are:
Unified meter and A/C amp.
Upper ventilator door motor (LCU)
A/C LAN system (PBR built-in mode door motor, upper ventilator door motor, air mix door motor and
intake door motor)
Sunload sensor
System Operation
The unified meter and A/C amp. receives data from each of the sensors. The unified meter and A/C amp.
sends air mix door, mode door, upper ventilator door and intake door opening angle data to the air mix door
motor LCUs, mode door motor LCUs, upper ventilator door motor LCU and intake door motor LCU.
The air mix door motors, mode door motors, upper ventilator door motor and intake door motor read their
respective signals according to the address signal. Opening angle indication signals received from the unified
meter and A/C amp. and each of the motor position sensors are compared by the LCUs in each door motor
with the existing decision and opening angles. Subsequently, HOT/COLD, DEF/VENT, OPEN/SHUT and FRE/
REC operation is selected. The new selection data are returned to the unified meter and A/C amp.
RJIA4060E
Page 533 of 4647
ATC-82
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
Air Mix Door Motor CircuitNJS000GQ
SYMPTOM
Discharge air temperature does not change.
Air mix door motor does not operate normally.
INSPECTION FLOW
*1ATC-57, "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 2 to 6.*2ATC-112, "
Ambient Sensor Circuit"*3ATC-115, "In-vehicle Sensor Circuit"
*4ATC-118, "Sunload Sensor Circuit"*5ATC-82, "Air Mix Door Motor Circuit"*6ATC-57, "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 13.
*7ATC-71, "
LAN System Circuit"*8ATC-65, "Operational Check"*9ATC-41, "SYMPTOM TABLE"
*10ATC-121, "Intake Sensor Circuit"
SJIA1762E
Page 534 of 4647
TROUBLE DIAGNOSIS
ATC-83
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
SYSTEM DESCRIPTION
Component Parts
Air mix door control system components are:
Unified meter and A/C amp.
Air mix door motor (LCU)
A/C LAN system (PBR built-in mode door motor, upper ventilator door motor, air mix door motor and
intake door motor)
In-vehicle sensor
Ambient sensor
Sunload sensor
Intake sensor
System Operation
The unified meter and A/C amp. receives data from each of the sensors. The unified meter and A/C amp.
sends air mix door, mode door, upper ventilator door and intake door opening angle data to the air mix door
motor LCUs, mode door motor LCUs, upper ventilator door motor LCU and intake door motor LCU.
The air mix door motors, mode door motors, upper ventilator door motor and intake door motor read their
respective signals according to the address signal. Opening angle indication signals received from the unified
meter and A/C amp. and each of the motor position sensors are compared by the LCUs in each door motor
with the existing decision and opening angles. Subsequently, HOT/COLD, DEF/VENT, OPEN/SHUT and FRE/
REC operation is selected. The new selection data are returned to the unified meter and A/C amp.
Air Mix Door Control Specification
RJIA4217E
RJIA1782E
Page 536 of 4647
TROUBLE DIAGNOSIS
ATC-85
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
Intake Door Motor CircuitNJS000GS
SYMPTOM
Intake door does not change.
Intake door motor does not operate normally.
INSPECTION FLOW
*1ATC-57, "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 2 to 6.*2AT C - 11 2 , "
Ambient Sensor Circuit"*3ATC-115, "In-vehicle Sensor Circuit"
*4ATC-118, "Sunload Sensor Circuit"*5AT C - 8 2 , "Air Mix Door Motor Cir-
cuit"
*6ATC-57, "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 13.
*7ATC-71, "
LAN System Circuit"*8ATC-132, "INTAKE DOOR
MOTOR"
*9ATC-65, "Operational Check"
*10ATC-41, "SYMPTOM TABLE"*11ATC-121, "Intake Sensor Circuit"
RJIA4066E
Page 537 of 4647
ATC-86
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
SYSTEM DESCRIPTION
Component Parts
Intake door control system components are:
Unified meter and A/C amp.
Intake door motor (LCU)
A/C LAN system (PBR built-in mode door motor, upper ventilator door motor, air mix door motor and
intake door motor)
In-vehicle sensor
Ambient sensor
Sunload sensor
Intake sensor
System Operation
The intake door control determines intake door position based on the ambient temperature, the intake air tem-
perature and the in-vehicle temperature. When shifting mode position D/F, when the DEF or OFF switches are
pressed, or when A/C switch is OFF, the unified meter and A/C amp. sets the intake door at the FRE position.
Intake Door Control Specification
RJIA4214E
RJIA4067E
Page 539 of 4647
ATC-88
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
Blower Motor CircuitNJS000GT
SYMPTOM: Blower motor operation is malfunctioning.
INSPECTION FLOW
*1AT C - 6 5 , "Operational Check"*2ATC-121, "Intake Sensor Circuit"*3AT C - 5 7 , "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 2.
*4AT C - 5 7 , "
FUNCTION CONFIRMA-
TION PROCEDURE", see No. 6.*5ATC-57, "
FUNCTION CONFIRMA-
TION PROCEDURE", see No. 13.*6AT C - 9 0 , "
DIAGNOSIS PROCE-
DURE FOR BLOWER MOTOR"
*7AT C - 4 1 , "SYMPTOM TABLE"*8ATC-112, "Ambient Sensor Circuit"*9AT C - 11 5 , "In-vehicle Sensor Circuit"
*10AT C - 11 8 , "Sunload Sensor Circuit"*11EC-214, "DTC P0117, P0118 ECT
SENSOR" (VQ35DE) or EC-926,
"DTC P0117, P0118 ECT SEN-
SOR" (VK45DE)
RJIA4069E
Page 540 of 4647
TROUBLE DIAGNOSIS
ATC-89
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
SYSTEM DESCRIPTION
Component Parts
Fan speed control system components are:
Unified meter and A/C amp.
A/C LAN system (PBR built-in mode door motor, upper ventilator door motor, air mix door motor and
intake door motor)
In-vehicle sensor
Ambient sensor
Sunload sensor
Intake sensor
System Operation
Automatic Mode
In the automatic mode, the blower motor speed is calculated by the unified meter and A/C amp. based on the
input from the PBR, in-vehicle sensor, sunload sensor, intake sensor and ambient sensor.
When the air flow is increased, the duty ratio of the blower fan motor’s drive signal is changed at 8%/sec. to
prevent a sudden increase in air flow.
In addition to manual air flow control and the usual automatic air flow control, starting air flow control, low
water temperature starting control and high passenger compartment temperature starting control are avail-
able.
RJIA4070E
Page 544 of 4647
TROUBLE DIAGNOSIS
ATC-93
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
Magnet Clutch CircuitNJS000GU
SYMPTOM: Magnet clutch does not engage.
INSPECTION FLOW
*1ATC-121, "Intake Sensor Circuit"*2ATC-112, "Ambient Sensor Circuit"*3AT C - 5 7 , "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 13.
*4AT C - 9 4 , "
DIAGNOSIS PROCE-
DURE FOR MAGNET CLUTCH"
*5ATC-104, "TROUBLE DIAGNOSIS
FOR UNUSUAL PRESSURE"
*6AT C - 6 5 , "Operational Check"
*7AT C - 5 7 , "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 2 to 6.*8ATC-41, "
SYMPTOM TABLE"
RJIA4077E
Page 545 of 4647
ATC-94
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
SYSTEM DESCRIPTION
Unified meter and A/C amp. controls compressor operation by ambient temperature, intake air temperature
and signal from ECM.
Low Temperature Protection Control
Unified meter and A/C amp. will turn compressor ON or OFF as determined by a signal detected by ambient
sensor and intake sensor.
When ambient temperature is higher than −2°C (28°F), the compres-
sor turns ON. The compressor turns OFF when ambient temperature
is lower than −5°C (23°F).
When intake air temperature is higher than 1°C (34°F), the compres-
sor turns ON. The compressor turns OFF when intake air tempera-
ture is lower than −5°C (23°F).
DIAGNOSIS PROCEDURE FOR MAGNET CLUTCH
SYMPTOM: Magnet clutch does not engage when A/C switch is ON.
RHA094GB
SJIA0267E
RJIA4078E
Page 546 of 4647
TROUBLE DIAGNOSIS
ATC-95
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
1. CHECK AMBIENT SENSOR AND INTAKE SENSOR CIRCUIT
Check ambient sensor and intake sensor. Refer to AT C - 5 7 , "
FUNCTION CONFIRMATION PROCEDURE" ,
see No. 9 and 11.
OK or NG
OK >> GO TO 2.
NG >>
Malfunctioning ambient sensor: Refer to AT C - 11 2 , "Ambient Sensor Circuit" .
Malfunctioning intake sensor: Refer to ATC-121, "Intake Sensor Circuit" .
2. PERFORM AUTO ACTIVE TEST
Refer to PG-23, "
Auto Active Test" .
Does the magnet clutch operate?
YES >>WITH CONSULT-II: GO TO 5.
WITHOUT CONSULT-II: GO TO 6.
NO >> Check 10A fuse (No. 79, located in IPDM E/R). Refer to PG-28, "
IPDM E/R Terminal Arrange-
ment" , and GO TO 3.
3. CHECK CIRCUIT CONTINUITY BETWEEN IPDM E/R AND COMPRESSOR
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and compressor connector.
3. Check continuity between IPDM E/R harness connector E8 ter-
minal 34 and compressor harness connector F24 terminal 1.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4. CHECK MAGNET CLUTCH CIRCUIT
Check for operation sound when applying battery voltage direct cur-
rent to terminal.
OK or NG
OK >> 1. Replace IPDM E/R.
2. Go to self-diagnosis procedure AT C - 5 7 , "
FUNCTION
CONFIRMATION PROCEDURE" and perform self-
diagnosis STEP-4. Confirm that magnet clutch opera-
tion normal.
NG >> 1. Replace compressor.
2. Go to self-diagnosis procedure AT C - 5 7 , "
FUNCTION
CONFIRMATION PROCEDURE" and perform self-
diagnosis STEP-4. Confirm that magnet clutch operation normal.
34 – 1 : Continuity should exist.
RJIA4079E
RJIA2005E