suspension INFINITI M35 2007 Factory Workshop Manual

INFINITI M35 2007 Factory Workshop Manual M35 2007 INFINITI INFINITI https://www.carmanualsonline.info/img/42/57024/w960_57024-0.png INFINITI M35 2007 Factory Workshop Manual

Page 3809 of 4647

INFINITI M35 2007  Factory Workshop Manual MA-10
PERIODIC MAINTENANCE
Revision: 2007 April2007 M35/M45
Schedule 2NLS0007D
EMISSION CONTROL SYSTEM MAINTENANCE
Abbreviations: R = Replace. I = Inspect. Correct or replace if necessary. [ ]: At the

Page 3836 of 4647

INFINITI M35 2007  Factory Workshop Manual CHASSIS AND BODY MAINTENANCE
MA-37
C
D
E
F
G
H
I
J
K
MA
B
MA
Revision: 2007 April2007 M35/M45
Checking Power Steering Fluid and LinesNLS0008E
Check fluid level in reservoir tank with engine off. 
Use

Page 3970 of 4647

INFINITI M35 2007  Factory Workshop Manual NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
PR-3
C
E
F
G
H
I
J
K
L
MA
B
PR
Revision: 2007 April2007 M35/M45
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting C

Page 3988 of 4647

INFINITI M35 2007  Factory Workshop Manual NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
PS-7
C
D
E
F
H
I
J
K
L
MA
B
PS
Revision: 2007 April2007 M35/M45
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Trouble Shooting

Page 3991 of 4647

INFINITI M35 2007  Factory Workshop Manual PS-10
STEERING WHEEL
Revision: 2007 April2007 M35/M45
STEERING WHEELPFP:48430
On-Vehicle Inspection and ServiceNGS000D8
CHECKING CONDITION OF INSTALLATION
Check installation conditions of steering ge

Page 3992 of 4647

INFINITI M35 2007  Factory Workshop Manual STEERING WHEEL
PS-11
C
D
E
F
H
I
J
K
L
MA
B
PS
Revision: 2007 April2007 M35/M45
c. While pulling outer socket slowly in ±11 . 5  m m  (±0.453 in) range
from neutral position, make sure rack sliding

Page 4001 of 4647

INFINITI M35 2007  Factory Workshop Manual PS-20
POWER STEERING GEAR AND LINKAGE
Revision: 2007 April2007 M35/M45
8. Remove steering hydraulic piping bracket from front suspension member. Refer to PS-39, "HYDRAULIC
LINE" .
9. Remove power stee

Page 4030 of 4647

INFINITI M35 2007  Factory Workshop Manual PREPARATION
RAX-3
C
E
F
G
H
I
J
K
L
MA
B
RAX
Revision: 2007 April2007 M35/M45
PREPARATIONPFP:00002
Special Service Tools [SST]NDS000FN
The actual shapes of Kent-Moore tools may differ from those of sp

Page 4031 of 4647

INFINITI M35 2007  Factory Workshop Manual RAX-4
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
Revision: 2007 April2007 M35/M45
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting ChartNDS000FP
Use chart be

Page 4033 of 4647

INFINITI M35 2007  Factory Workshop Manual RAX-6
WHEEL HUB
Revision: 2007 April2007 M35/M45
5. Separate the wheel hub and bearing assembly from drive shaft
by lightly tapping the end with a hammer (suitable tool) and
wood block, and then remov