battery INFINITI M35 2007 Factory Manual Online

BCS-8
BCM (BODY CONTROL MODULE)
Revision: 2007 April2007 M35/M45
MAJOR COMPONENTS AND CONTROL SYSTEM
System Input Output
Intelligent Key system Intelligent Key unit

All door locking actuator

Trunk lid opener actuator

Turn signal lamp (LH, RH)

Combination meter
Power door lock system

Power window main switch (door lock and unlock switch)

Power window sub switch (passenger side)
(door lock and unlock switch)All-door locking actuator
Power supply (IGN) to power win-
dow, sunroofIgnition power supply Power window and sunroof system
Power supply (BAT) to power win-
dow, sunroof and power seatBattery power supplyPower window, sunroof system
and power seat
Panic alarm

Key slot

Intelligent KeyIPDM E/R
Theft warning system

All-door switch

Hood switch

Intelligent Key

Power window main switch (door lock and unlock switch)

IPDM E/R

Security indicator lamp
Auto light system

Optical sensor

Combination switchIPDM E/R
Exterior lamp battery saver control

Ignition switch

Combination switchIPDM E/R

Headlamp

Tail lampCombination switch

IPDM E/R

Combination meter
Front fog lamp Combination switch

IPDM E/R

Combination meter
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Interior room lamp timer

Key switch

Power window main switch (door lock and unlock switch)

Front door switch driver side

All-door switchInterior room lamp
Key warning chime*
1
Key switch

Front door switch driver sideCombination meter
(warning buzzer)
Light warning chime

Combination switch

Front door switch driver sideCombination meter
(warning buzzer)
Tire pressure monitoring system Low tire pressure warning control unitCombination meter
(warning buzzer)
(warning lamp)
Seat belt warning chime

Combination meter [Seat belt buckle (driver side) switch]

Ignition switchCombination meter
(warning buzzer)
Vehicle-speed-sensing intermittent
wiper

Combination switch

Unified meter and A/C amp.IPDM E/R
Rear window defogger

Multifunction switch

NAVI control unit*2

AV control unit*3
IPDM E/R

BCS-12
BCM (BODY CONTROL MODULE)
Revision: 2007 April2007 M35/M45
CONSULT-II Function (BCM)NKS003XK
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II BASIC OPERATION
Refer to GI-38, "CONSULT-II Start Procedure" .
ITEMS OF EACH PART
×: Applicable
NOTE:
CONSULT-II displays systems equipped in the vehicle.BCM diagnostic test item Check item, diagnostic test mode Content
Inspection by partWORK SUPPORT Changes setting of each function.
SELF- DIAG RESULTS BCM performs self-diagnosis of CAN communication.
DATA MONITOR Displays the input data of BCM in real time.
CAN DIAG SUPPORT MNTRThe result of transmit/receive diagnosis of CAN communication can
be read.
ACTIVE TEST Gives a drive signal to a load to check the operation.
ECU PART NUMBER BCM part number can be read.
System and item CONSULT-II displayDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−DIAG
RESULTSDATA
MONITORCAN DIAG
SUPPORT
MNTRACTIVE
TESTECU
PA R T
NUMBER
BCM BCM×× × ×
Power door lock system DOOR LOCK××
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Room lamp timer INT LAMP×××
Headlamp HEAD LAMP×××
Wiper WIPER×××
Turn signal lamp
Hazard lampFLASHER××
Intelligent Key system INTELLIGENT KEY××
Combination switch COMB SW×
IVIS IMMU××
Room lamp battery saver BATTERY SAVER×× ×
Trunk lid TRUNK××
Vehicle security system THEFT ALM×××
Retained power control RETAINED PWR××
Oil pressure switch SIGNAL BUFFER××
Panic system PANIC ALARM×

BCS-14
BCM (BODY CONTROL MODULE)
Revision: 2007 April2007 M35/M45
Check BCM Power Supply and Ground CircuitNKS003XM
1. CHECK FUSES AND FUSIBLE LINK
Check for blown fuses and fusible link.
Refer to LT-13, "Wiring Diagram — H/LAMP —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse or fusible link is blown, be sure to eliminate cause of malfunction before installing new fuse
or fusible link. Refer to PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Unit Power source Fuse and fusible link No.
BCMBatteryF
21
Ignition switch ON or START position 1
Ignition switch ACC or ON position 6
Terminal Ignition switch position
(+)
(-) OFF ACC ON
BCM
ConnectorTerminal
M111
GroundApprox. 0 VBattery
voltageBattery
voltage
38 Approx. 0 V Approx. 0 VBattery
voltage
M242 Battery
voltageBattery
voltageBattery
voltage
55 Battery
voltageBattery
voltageBattery
voltage
PKIA5204E
Terminal Continuity
BCM
ConnectorTerminal
Ground Yes
M2 52
SKIB5125E

BL-1
BODY, LOCK & SECURITY SYSTEM
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION BL
A
B
BL
Revision: 2007 April2007 M35/M45
BODY, LOCK & SECURITY SYSTEM
PRECAUTIONS .......................................................... 6
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 6
Precautions for Procedures without Cowl Top Cover ..... 6
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 6
OPERATION PROCEDURE ................................. 6
Precautions for Work ................................................ 7
PREPARATION ........................................................... 8
Special Service Tools ............................................... 8
Commercial Service Tools ........................................ 8
SQUEAK AND RATTLE TROUBLE DIAGNOSIS ...... 9
Work Flow ................................................................ 9
CUSTOMER INTERVIEW ..................................... 9
DUPLICATE THE NOISE AND TEST DRIVE ..... 10
CHECK RELATED SERVICE BULLETINS ......... 10
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE .................................................... 10
REPAIR THE CAUSE ......................................... 10
CONFIRM THE REPAIR ...................................... 11
Generic Squeak and Rattle Troubleshooting .......... 11
INSTRUMENT PANEL ......................................... 11
CENTER CONSOLE ............................................ 11
DOORS ................................................................ 11
TRUNK ................................................................ 12
SUNROOF/HEADLINING ................................... 12
SEATS ................................................................. 12
UNDERHOOD ..................................................... 12
Diagnostic Worksheet ............................................ 13
HOOD ....................................................................... 15
Fitting Adjustment .................................................. 15
Removal and Installation of Hood Assembly .......... 17
REMOVAL ........................................................... 17
INSTALLETION ................................................... 18
Removal and Installation of Hood Lock Control ..... 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 19
Hood Lock Control Inspection ................................ 20RADIATOR CORE SUPPORT .................................. 21
Removal and Installation ........................................ 21
REMOVAL ........................................................... 21
INSTALLATION ................................................... 22
FRONT FENDER ...................................................... 23
Removal and Installation ........................................ 23
REMOVAL ........................................................... 23
INSTALLATION ................................................... 23
POWER DOOR LOCK SYSTEM .............................. 24
Component Parts and Harness Connector Location ... 24
System Description ................................................. 25
DOOR LOCK ACTUATOR OPERATION ............. 26
FUEL LID OPERATION ....................................... 26
OUTLINE ............................................................. 26
CAN Communication System Description .............. 26
CAN Communication Unit ....................................... 26
Schematic ............................................................... 27
Wiring Diagram —D/LOCK— ................................. 28
Terminals and Reference Value of BCM ................. 31
Work Flow ............................................................... 31
CONSULT-II Function (BCM) ................................. 32
CONSULT-II START PROCEDURE .................... 32
CONSULT-II APPLICATION ITEMS .................... 32
Trouble Diagnosis Chart by Symptom .................... 33
Power Supply and Ground Circuit Check of BCM ... 34
Check Door Lock and Unlock Switch ..................... 35
Check Door Lock Actuator/Driver Side ................... 37
Check Door Lock Actuator/Passenger Side ........... 38
Check Door Lock Actuator/Rear LH ....................... 39
Check Door Lock Actuator/Rear RH ....................... 39
Check Fuel Lid Opener Actuator ............................ 40
Door Key Cylinder Switch Check ............................ 41
INTELLIGENT KEY SYSTEM ................................... 43
Component Parts and Harness Connector Location ... 43
System Description ................................................. 47
DOOR LOCK/UNLOCK/TRUNK OPEN FUNC-
TION .................................................................... 47
REMOTE KEYLESS ENTRY FUNCTIONS ......... 51
ENGINE START FUNCTION ............................... 53
WARNING FUNCTION ........................................ 54

BL-2Revision: 2007 April2007 M35/M45 CHANGE SETTINGS FUNCTION ....................... 59
INTELLIGENT KEY REGISTRATION .................. 59
STEERING LOCK UNIT REGISTRATION .......... 59
CAN Communication System Description .............. 59
CAN Communication Unit ....................................... 59
Schematic ............................................................... 60
Wiring Diagram — I/KEY— .................................... 62
Terminals and Reference Value for Intelligent Key
Unit ......................................................................... 73
Terminals and Reference Value for BCM ................ 76
Terminals and Reference Value for IPDM E/R ........ 76
Trouble Diagnosis Procedure ................................. 77
WORK FLOW ...................................................... 77
CONSULT-II Functions (INTELLIGENT KEY) ........ 79
CONSULT-II Inspection Procedure ......................... 79
BASIC OPERATION ............................................ 79
CONSULT-II Application Items ............................... 79
SELF-DIAGNOSTIC RESULTS ........................... 79
DATA MONITOR .................................................. 80
WORK SUPPORT ............................................... 81
ACTIVE TEST ..................................................... 83
Trouble Diagnosis Symptom Chart ......................... 84
ALL FUNCTIONS OF INTELLIGENT KEY SYS-
TEM DOES NOT OPERATE ............................... 84
DOOR LOCK/UNLOCK FUNCTION MALFUNC-
TION .................................................................... 84
REMOTE KEYLESS ENTRY FUNCTION MAL-
FUNCTION .......................................................... 85
TRUNK OPEN FUNCTION MALFUNCTION ...... 86
HAZARD AND BUZZER REMINDER FUNC-
TION MALFUNCTION ......................................... 87
HAZARD AND HORN REMINDER FUNCTION
MALFUNCTION ................................................... 87
POWER WINDOW DOWN FUNCTION MAL-
FUNCTION .......................................................... 88
WARNING FUNCTION MALFUNCTION ............. 88
Check CAN Communication System ...................... 90
Check Power Supply and Ground Circuit ............... 91
Check Key Slot ....................................................... 92
Check Door Switch ................................................. 94
Check Trunk Room Lamp Switch ........................... 97
Check Door Request Switch ................................... 99
Check Trunk Opener Request Switch ..................101
Check Unlock Sensor ...........................................103
Check Intelligent Key Warning Buzzer .................105
Check Outside Key Antenna (Driver Side and Pas-
senger Side) .........................................................106
Check Outside Key Antenna (Trunk Room) .........108
Check Inside Key Antenna ...................................110
Check Park Position Switch ..................................113
Check Ignition Switch Position .............................115
Check Remote Keyless Entry Receiver ................115
Check Trunk Lid Opener Cancel Switch ...............119
Check Key Slot Illumination ..................................121
Check Horn Function ............................................122
Check Combination Meter Display Function .........122
Check Warning Chime Function ...........................123
Removal and Installation of Intelligent Key Unit ...123
REMOVAL .........................................................123INSTALLATION ..................................................123
Intelligent Key Battery Replacement .....................124
DISASSEMBLY AND ASSEMBLY OF INTELLI-
GENT KEY .........................................................124
INTELLIGENT KEY BATTERY INSPECTION ...124
INTELLIGENT KEY SYSTEM/ENGINE START
FUNCTION ..............................................................125
Component Parts and Harness Connector Location .125
System Description ...............................................126
PRECAUTIONS FOR INTELLIGENT KEY SYS-
TEM ...................................................................127
Operation Description ...........................................127
SYSTEM DIAGRAM ..........................................127
OPERATION WHEN INTELLIGENT KEY IS
CARRIED ...........................................................127
OPERATION WHEN KEY SLOT IS USED ........128
PUSH-BUTTON IGNITION SWITCH OPERA-
TION PROCEDURE ..........................................128
CAN Communication System Description ............129
CAN Communication Unit .....................................129
Schematic .............................................................130
Wiring Diagram — ENG/ST — ..............................132
Terminals and Reference Value for Intelligent Key
Unit ........................................................................141
Terminals and Reference Value for Steering Lock
Unit ........................................................................145
Terminals and Reference Value for BCM ..............145
Terminals and Reference Value for IPDM E/R ......146
Terminals and Reference Value for PDU ..............147
Work Flow .............................................................148
CONSULT-II Functions (INTELLIGENT KEY) .......150
CONSULT-II Inspection Procedure .......................150
BASIC OPERATION ..........................................150
CONSULT-II Application Items ..............................150
SELF-DIAGNOSTIC RESULTS .........................150
DATA MONITOR ................................................151
WORK SUPPORT .............................................152
ACTIVE TEST ....................................................153
DTC B2013 STRG COMM 1 .................................155
DIAGNOSIS DESCRIPTION .............................155
TERMINALS AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ..................................155
SELF-DIAGNOSTIC LOGIC ..............................155
DIAGNOSTIC PROCEDURE .............................155
DTC B2551 STEERING LOCK UNIT ....................157
DIAGNOSIS DESCRIPTION .............................157
TERMINALS AND REFERENCE VALUE ..........157
SELF-DIAGNOSTIC LOGIC ..............................158
DIAGNOSTIC PROCEDURE .............................158
DTC B2552 INTELLIGENT KEY ...........................161
DIAGNOSIS DESCRIPTION .............................161
DTC B2553 IGN POWER CIRCUIT ......................161
DIAGNOSIS DESCRIPTION .............................161
TERMINAL AND REFERENCE VALUE FOR
INTELLIGENT KEY UNIT ..................................161
CONSULT-II DATA MONITOR STANDARD
VALUE ...............................................................161
SELF-DIAGNOSTIC LOGIC ..............................162
DIAGNOSTIC PROCEDURE .............................162

BL-6
PRECAUTIONS
Revision: 2007 April2007 M35/M45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NIS002B4
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Procedures without Cowl Top CoverNIS001WB
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectNIS001WC
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.

Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
PIIB3706J

PRECAUTIONS
BL-7
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
Precautions for WorkNIS001WD

After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check
their operational.

Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

POWER DOOR LOCK SYSTEM
BL-31
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Terminals and Reference Value of BCMNIS001WV
Work FlowNIS001WW
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to BL-25, "
System Description" .
3. According to the trouble diagnosis chart by symptom, repair or replace the cause of the malfunction.
Refer to BL-33, "
Trouble Diagnosis Chart by Symptom" .
4. Does power door lock system operate normally?
YES: GO TO 5.
NO: GO TO 3.
5. INSPECTION END
Te r m i -
nalWire
colorItemSignal
Input/
OutputConditionVoltage [V]
(Approx.)
11 V Ignition switch (ACC) Input Ignition switch is in ACC position Battery voltage
22 G Power window serial link Input Ignition switch ON
38 W Ignition switch (ON) InputIgnition switch is in ON or START
positionBattery voltage
39 L CAN HInput/
Output——
40 P CAN LInput/
Output——
42 P Battery source (Fuse) Input — Battery voltage
44 GRDriver door lock actuator
(unlock) signalOutputDoor lock / unlock switch
(Free → Unlock)0 → Battery voltage → 0
50 VDoor lock actuator (lock)
signalOutputDoor lock / unlock switch
(Free → Lock)0 → Battery voltage → 0
51 GRear doors lock actuator
signalOutputDoor lock / unlock switch
(Free → Unlock)0 → Battery voltage → 0
52 B Ground — — 0
55 W Power source (Fusible link) Input — Battery voltage
69 Vfuel lid lock actuator
(unlock) signalOutputDoor lock / unlock switch
(Free → Unlock)0 → Battery voltage → 0
70 GFront door lock actuator
(passenger side) lock signalOutputDoor lock / unlock switch
(Free → Unlock)0 → Battery voltage → 0
PIIA2344J

BL-34
POWER DOOR LOCK SYSTEM
Revision: 2007 April2007 M35/M45
Power Supply and Ground Circuit Check of BCMNIS001WZ
1. CHECK FUSE
Check the following fuse and fusible link.

50A fusible link (letter F , located in the fuse and fusible link box)

10A fuse [No.21, located in the fuse block (J/B)]

10A fuse [No.6, located in the fuse block (J/B)]

15A fuse [No.1, located in the fuse block (J/B)]
NOTE:
Refer to BL-24, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse, refer to PG-
3, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check voltage between BCM and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace BCM power supply circuit.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Repair or replace BCM ground circuit.
Terminals Condition
of ignition
switch
positionVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M311
GroundACC
Battery voltage 38 ON
M242
OFF
55
PIIB6296E
BCM connector Terminal Continuity
M2 52 Ground Yes
PIIB5935E

POWER DOOR LOCK SYSTEM
BL-37
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Check Door Lock Actuator/Driver SideNIS001X1
1. CHECK OUTPUT SIGNAL
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
2. CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and front door lock actuator driver side connector.
3. Check continuity between BCM connector and front door lock
actuator driver side connector.
4. Check continuity between BCM connector and ground.
OK or NG
OK >> Replace front door lock actuator (driver side).
NG >> Repair or replace harness.
Terminals
Condition of
door lock and
unlock switchVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M250
GroundLock 0 → Battery voltage → 0
44 Unlock 0 → Battery voltage → 0
PIIB6060E
AB
Continuity
BCM connector TerminalDoor lock actu-
ator connectorTe r m i n a l
M250
D142
Ye s
44 1
A
Continuity
BCM connector Terminal
M250
Ground No
44
PIIB6061E