light INFINITI Q50 2015 Quick Reference Guide

18
first drive features
8 INTAKE AIR CONTROL BUTTON

Pressing the intake air control button will cancel auto air recirculation 7
(if so equipped) until it is re-activated from the touch-screen (see above). Press the
intake air control button
to manually control whether the interior air is recirculated
or outside air is drawn into the vehicle. When the indicator light is on, interior air
is recirculated, outside odors are avoided and interior vehicle temperature is most
effectively maintained.

The air recirculation mode cannot be activated when the climate control system is in the
front defroster mode

or the front defroster and foot vent mode .
9 A/C KEY

Touch the A/C key to turn the air conditioner system on or off. This system helps cool
and dehumidify the air inside the cabin and defog the windows.
10 DUAL KEY

Touch to turn the passenger’s side temperature controls on or off. When the system
is on, the indicator light will illuminate. This function will allow the passenger’s side
temperature to be adjusted independently from the driver’s side by pressing the
passenger’s side temperature control buttons

3.
11 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS

Press the defroster button
to turn the system on. The A/C automatically turns
on when the defroster mode is selected. This feature removes humidity from the air.


To defrost the front and side windows, set the driver’s side temperature controls
2 and
fan speed controls 4 to their maximum settings.
12
DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS

Push the rear window and outside mirror defroster switch
to turn the system
on or off.

This function automatically turns off after approximately 15 minutes.
13 ON/OFF BUTTON

Press the ON/OFF button to turn the climate control system on or off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual and the “Heater and air
conditioner (section 3)” of your InTouch Owner’s Manual.
2045927_15c_Infiniti_Q50_QRG_071415.indd 187/14/15 3:39 PM

20
first drive features
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a constant cruising speed once the vehicle has
reached 25 mph (40 km/h).

The system will automatically maintain the set speed until you tap the brake pedal,
accelerate, cancel or turn the system off.

To activate the cruise control, push the ON/OFF switch. The CRUISE indicator light in the
instrument panel will illuminate.

To set a cruising speed, accelerate the vehicle to the desired speed, push the SET – switch
and release. The CRUISE SET indicator light
in the instrument panel will illuminate. Take
your foot off the accelerator pedal. Your vehicle will maintain the set speed.

To reset at a faster cruising speed, push and hold the RES + switch. When the vehicle
attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the SET – switch. Release the switch
when the vehicle slows to the desired speed.

To cancel the preset speed, tap the brake pedal or push the CANCEL switch.

To turn off cruise control, push the ON/OFF switch. The CRUISE indicator light
in the
instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
USB (Universal Serial Bus) Connection Port/iPod® Interface
The USB port
1 is located in the center console
under the armrest.

When a compatible USB memor y device or iPod® is
plugged into the USB por t:
• A confirmation message appears. Select “ Yes”
if you prefer to use the devices with Voice
Recognition in which song titles and ar tist names are registered in the system.
• Compatible audio files stored on the device can be played through the vehicle’s audio
system and front display.

If t wo USB devices are plugged in at the same time, you are able to use Voice
Recognition to choose which one should play. Just press the
but ton on the steering
wheel to activate Voice Recognition and follow the voice prompts.

This vehicle is equipped with Audio and Video RC A inputs 2. This will allow you to play
audio and video through your vehicle from an external source.
For more information, refer to the “Getting Started (section 2)”, the “Audio system (section 4)” and the “Voice recognition
(section 10)” of your InTouch Owner’s Manual.
1 2
2045927_15c_Infiniti_Q50_QRG_071415.indd 207/14/15 3:39 PM

21
Intelligent Cruise Control (ICC) (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set vehicle-to-vehicle distance control mode,
press the
button
1 for less than 1.5 seconds.
The gray indicator light 2 will illuminate.

Accelerate to the desired speed.

Push down on the SET – switch
3 and release it.
Intelligent Cruise Control will be set to the
desired speed.

Press the distance button
4 repeatedly to change
the set distance between long, middle and short.

When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed
indicator lights will illuminate

5 in set mode.

When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance and set
vehicle speed indicator lights will illuminate

6 in
set mode.

To reset at a faster cruising speed, push up and hold
the RES + switch
7. When the vehicle attains the
desired speed, release the switch.

To reset at a slower cruising speed, push down and
hold the SET – switch

3. Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
8. The set vehicle speed indicator
5 will change to grey.

To turn off Intelligent Cruise Control, press the button
1. The indicator light 2 in
the instrument panel will extinguish.
To set conventional (fixed speed) cruise control mode:

While Intelligent Cruise Control is off, press the button
1 and hold it down for more
than 1.5 seconds. The grey indicator light will illuminate.

Accelerate to the desired speed.

Push down on the SET – switch and release it. The green indicator light will illuminate.
Cruise control should be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
2
5
6
1 8
4
7
3
2045927_15c_Infiniti_Q50_QRG_071415.indd 217/14/15 3:39 PM

25
RECEIVING/ENDING A CALL


To accept the call, press the
button on the steering
wheel or touch the Answer key.

To reject the call, touch the Decline key.



To hang-up, press the
button or touch the
Hang Up key.
For more information, refer to the “Hands-Free Phone (section 5)” and the
“Voice recognition (section 10) of your InTouch Owner’s Manual or
please visit www.InfinitiUSA.com/bluetooth.
Navigation System (if so equipped)
INFINITI CONTROLLER – Turn to highlight
an item and press ENTER to select the
highlighted item on the upper display
menu screen. On the map screen, turn to
adjust the map scale. To scroll the map,
push the controller in the direction you
want to scroll.

1
Upper Display – Displays the map and can
be controlled by the INFINITI controller.

2
Lower Display – Displays navigation
functions and is not controlled by the
INFINITI controller. Press the MENU button
below the lower display to access the
navigation functions.

3
Map Scale – Touch to display the scale bar.
Touch ZOOM IN or ZOOM OUT to adjust
the map scale.

4
Street Address – Touch to search for a destination by entering an address.

5
Points of Interest – Touch to search for a destination from different categories of
businesses or locations.

6
Home – Touch to search for a route from the vehicle’s current location to the stored
home location.

7
Destination – Touch to view multiple ways to set a destination.
For more information, refer to the “Navigation (section 9)” of your InTouch Owner’s Manual.
1
3
4 5
2
6 7
2045927_15c_Infiniti_Q50_QRG_071415.indd 257/14/15 3:40 PM

26
system guide
HomeLink® Universal Transceiver (if so equipped)
The HomeLink® Universal Transceiver can learn and consolidate the functions of up to three
different hand-held transmitters, operating items such as garage doors, property gates,
outdoor and indoor lights or alarm systems.

To program the HomeLink® Universal Transceiver:
• Position the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink surface,
keeping the HomeLink indicator light in view.
• Press and hold the desired HomeLink button and the handheld transmitter button
simultaneously until the HomeLink indicator light flashes slowly and then rapidly.
• Both buttons may be released when the indicator light flashes rapidly.

To verify the programing is complete, press and hold the HomeLink button and observe the
indicator light:
• A solid, continuous light indicates the programing is complete and the HomeLink button
will activate your device.
• A blinking light that turns to a solid, continuous light after 2 seconds indicates additional
steps are required to complete the programing.

An additional person may make the remaining steps easier. To complete the
programing process:
• At the receiver of the device that you are programing to the HomeLink button, press and
release the learn or smart button (the name may vary by manufacturer, but it is usually
located near where the hanging antenna wire is attached to the unit). You have
approximately 30 seconds to initiate the following step.
• Press and hold the programed HomeLink button for 2 seconds and release.

You may have to repeat the previous two steps up to 3 times to complete the programing
process. HomeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website
at www.homelink.com or call 1-800-355-3515.
HOMELINK
2045927_15c_Infiniti_Q50_QRG_071415.indd 267/14/15 3:40 PM