light INFINITI Q50 2021 Quick Reference Guide

2
Cockpit Overview
Headlight and turn signal switch
Upper display and audio control switch
Voice Recognition control switches
Wiper and washer switch
Intelligent cruise control (ICC) switches (if so equipped)
Vehicle information display control switches

8
Two positions for the driver’s seat, steering
column and outside mirrors can be stored in
the automatic drive positioner memory. To set
a memory position:
1.

Plac
e the ignition switch in the ON
position. (The vehicle should be stopped
while setting the memory.)
2.


A
djust the driver’s seat, steering column
and outside mirrors to the desired
positions using the adjusting switches for each feature.
3

.
Push the
SET switch
, and within 5 seconds, push the memory switch
(1 or 2)
. The indicator light for the memory switch you select will
illuminate for approximately 5 seconds and a chime will sound when the
memory is stored.
The driver’s seat and steering column will automatically move when the driver’s
side door is opened, to allow the driver to get in and out of the driver’s seat
more easily. “Lift Steering upon Exit” and “Slide Driver Seat Back on Exit” can be
adjusted in the lower touch-screen display under “Comfort & Convenience”.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
Memory Seats (if so equipped)Starting/Stopping
the Engine
It is important to make sure the
INFINITI Intelligent Key is with you
(that is, in your pocket or purse).
1.


Depr
ess the brake pedal.
2.


Push the ignition swit
ch
START/STOP button to
the ON position.
TURNING THE ENGINE OFF
1.


M
ove the shift lever to the P (PARK) position and apply
the parking brake.
2.


Push the ignition swit
ch START/STOP button to turn
the engine off.
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.

9
HomeLink® Universal Transceiver (if so equipped)
HomeLink®
Before you start programing HomeLink®, park outside and within range of your garage. Then, clear the area around your garage door, place the
ignition switch in the ON or ACC position (without starting the engine) and locate the remote control transmitter, ensuring a fresh battery is
installed. Please note, a ladder and another person may be needed.
To program the HomeLink
® Universal Transceiver:
1.



P

osition the handheld transceiver 1-3 in (2-8 cm) away from the HomeLink surface, keeping the HomeLink indicator light in view.
2.



Pr

ess and hold the desired HomeLink button and the handheld transmitter button simultaneously until the HomeLink indicator light flashes
slowly and then rapidly.
3

.

Bo

th buttons may be released when the indicator light flashes rapidly.
4.



Pr

ess and hold the programed HomeLink button and observe the indicator light. A solid, continuous light indicates the programing is complete.
If the indicator light rapidly blinks for two seconds and then turns to a solid, continuous light, continue with steps for a rolling code device.
5.



A

t the receiver located on the garage door opener motor, locate the “learn” or “smart” button. If there is difficulty locating the button, reference
the garage door opener’s manual. Once the button is pressed, you have approximately 30 seconds to initiate the next step.
6.



Pr

ess and hold the programed HomeLink button for two seconds and release. Repeat the sequence up to three times to complete the
programing process. HomeLink should now activate your rolling code equipped device.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.

15
To adjust the time and the appearance of the clock
on the display:
1.
Press the MENU button
below the lower
display. Then select the “Settings” key on
the lower display.
2.


L

ocate and select the “Clock” key to adjust
“On-Screen Clock”, “Daylight Savings Time”,
“Clock Format (24h)” and “Time Zone”.
Clock Set/Adjustment
Please see your INFINITI InTouch™ Owner’s Manual for important
safety information, system limitations, and additional operating
and feature information.
Connecting your Cellular Phone
or Device via Bluetooth
®*
Using Bluetooth® technology, you can connect (pair) your cellular phone with the
in-vehicle system for hands-free use of your cellular phone.
1.



Pr

ess the MENU button below the lower display.
2.



Select the

“Settings” key on the lower display.
3

.

Select the

“Connections” key.
4.



Select the

“Add New” key.
5.



F

ollow the instructions on the screen. If a PIN appears on the screen, operate the
Bluetooth
® device to enter/confirm the PIN.
The paired cellular phone will be added to the list on the “Connections” screen.
FAVORITE HANDS-FREE PHONE
•


Y

ou can register a favorite hands-free phone. The phone device name selected as a
favorite will be marked with a star.
For any Bluetooth
® connectivity issues, reboot your cellular phone or device.
* Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your INFINITI InTouch™ Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.