belt INFINITI Q50 HYBRID 2015 Dismantling Guide

3-2 Personal Protective Equipment (PPE) and Insulated Tools
3-2.1 Personal Protective Equipment (PPE) Protective Wear Control
Perform an inspection of the Personal Protective Equipment (PPE) items before beginning work. Do not use
any damaged PPE items.
3-2.2 Daily Inspection
This inspection is performed before and after use. The worker who will be using the items should perform
the inspection and check for deterioration and damage.• Insulated rubber gloves should be inspected for scratches, holes and tears. (Visual check and airleakage test)
• Insulated safety boots should be inspected for holes, damage, nails, metal pieces, wear or other problems on the soles. (Visual check)
• Insulated rubber sheet should be inspected for tears. (Visual check)
3-2.3 Insulated Tools
When performing work at locations where high voltage is applied (such as terminals) , use insulated tools
meeting 1,000V/300A specifications.
3-3 Discharge Procedures
DANGER
Do not perform this procedure if the battery is damaged. If you are unsure of battery
damage, use extreme caution and wear appropriate Personal Protective Equipment (PPE) .
High voltage battery discharging must take place before dismantling. Sufficient discharging can be achieved
by following these steps. 1. Place the shift selector into the Park (P) position
2. Apply the parking brake.
3. Set wheel chocks to ensure the vehicle is completely immobilized.
4. Fasten the driver seat belt and close the driver door.
5. Apply foot brake and press the ignition switch to turn the system ON. Confirm READY
indicator in instrument cluster turns ON.a. If the engine starts, leave the engine on until the idling stops.
b. If the engine does NOT start, move on to next step.
6. Remove the shift lock cover (A) using a suitable tool.
7. Push down the shift lock (B) using mechanical key as shown in the illustration.
8. Push the shift selector button (C) and move the shift selector to the Neutral (N) position (D) while holding
down the shift lock.
NOTE:
DO NOT press accelerator or foot brake after
moving the shift selector to the Neutral (N)
position. Otherwise high voltage battery will
start to be charged.
A
B
C
D
DG–18

NOTE:
The engine must not be running at this time. If the engine has restarted, repeat the
previous steps.
9. Release the parking brake.
10. Unbuckle the seat belt and open the driver door. The READY
indicator should remain ON
and the engine should not be running.
11.
Turn ON electric devices such as headlamps, A/C (set to the coldest temperature) and rear window
defogger to discharge the high voltage battery. Discharge is complete when the READY
indicator (B) (green) turns OFF, and the hybrid system warning indicator (C) (orange) turns ON.
12. Move shift selector into the Park (P) position and press the ignition switch (A) to turn the system OFF.
Please contact following number if the vehicle could not be discharged. • 1-800-662-6200 (US) or 1-800-361-4792 (Canada)
• Hours of operation are 8am - 5pm (Monday-Friday) Eastern, Central and Pacific time zones.
A
B
C
LOCK
ACC
(OFF)
ON
AAYIA0078GB
DG–19

SRS Air Bag System Components Location
The SRS air bag system must not be cut as there is a risk of short circuit and unintentional deployment of
the SRS However, the vehicle can be cut (except inflators) under the following conditions:• The front, side and curtain air bags have deployed.
• At least three (3) minutes have passed after the 12-volt battery negative (-) cable has beendisconnected and the high voltage system has been shut down.
1. Crash zone sensor (located
underhood near hood latch) 2. Supplemental front air bag
modules (Infiniti Advanced
Air Bags)3. Front seat-mounted side-
impact supplemental air bags
4. Roof-mounted curtain side-
impact supplemental air bags 5. Roof-mounted curtain side-
impact supplemental air baginflators6. C-pillar satellite sensors
(LH shown, RH similar)
7. Seat belt buckle pretensioners 8. Seat belts with pretensioners 9. B-pillar satellite sensors
10. Air bag control unit (ACU) 11. Front door satellite sensors (LH shown, RH similar)
21
10
453
876911
AAYIA0189ZZ
DG–32

6-2.2 Removal Procedure1. Discharge high voltage battery. Refer to
3-3 Discharge Procedures (DG–18)
2. Remove the service plug. Refer toAlternate Procedure 2 (Remove Service Plug) (DG–27).
3. Lift up seat cushion while pulling the seat cushion hook levers, and then disengage seat cushion hook.
4. Remove seat cushion from vehicle.
5. Remove seat belt from seat belt hook.
6. Remove seatback fixing nuts (A) .
7. Lift up seatback, disengage seatback frame (B) from engaging portion (C) , and then remove seatback.
8. Remove battery inlet duct A and battery front duct. Refer to the high voltage Battery Cooling System Exploded View in
6-2.1 Exploded View (DG–43).
AAYIA0257ZZ
A
AAYIA0258ZZ
A
A
A
A
B
C
AAYIA0259ZZ
DG–46

35. Follow the procedure below to remove the battery pack from inside the trunk room.a. Attach carabiners (A) of sufficient capacity to hold battery weight, in the positions as shown
in the figure, then connect a belt slinger (B) to it.
DANGER
Touching high voltage components without wearing appropriate Personal Protective
Equipment (PPE) will cause electrocution.
b. Slightly lift battery pack by using an enginecrane (A) .
DANGER
Touching high voltage components without wearing
appropriate Personal Protective Equipment (PPE) will
cause electrocution.
c. Remove the bracket RH (1) .
ABB
A
AAYIA0252ZZ
A
AAYIA0254ZZ
1
AAYIA0253ZZ
DG–53