light INFINITI Q60 COUPE 2021 Quick Reference Guide

2
Cockpit Overview
Vehicle information display switches
Intelligent Cruise Control switches (if so equipped)
Wiper and washer switch
Paddle shifters (if so equipped)
Combined turn signal/Headlight control switch
Upper display control switches
Audio and Bluetooth® control switches
Instrument brightness control switches and Trip Reset switch
(behind steering wheel)

8
Two positions for the driver’s seat, steering column and outside mirrors can be stored in
the memory seat system. To set a memory position:
1.

Place the ignition swit
ch in the ON position. (The vehicle should be stopped while
setting the memory.)
2.


Adjust the driv
er’s seat, steering column
and outside mirrors to the desired
positions using the adjusting switches
for each feature.
3.




Push the SET
switch
, and within 5
seconds, push the memory switch (1 or 2)
. The indicator light for the memory
switch you select will illuminate for
approximately 5 seconds and a chime will
sound when the memory is stored.
The steering column will automatically move when the driver’s side door is
opened to allow the driver to get in and out of the driver’s seat more easily.
“Lift Steering upon Exit” and “Slide Driver Seat Back on Exit” can be adjusted in the
lower touch-screen display under “Comfort & Convenience”.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and
feature information.
Memory Seat (if so equipped)

10
AUTOMATIC ANTI-GLARE REARVIEW MIRROR
The inside mirror is designed so that it automatically dims during night-time
conditions and according to the intensity of the headlights of the vehicle following
you. The automatic anti-glare feature is activated when the ignition switch is in
the ON position.
• The indicat
or light
will illuminate when the automatic anti-glare
feature is operating.
• To turn o

ff the anti-glare feature, press the O button on the rearview mirror. The
indicator light will turn off.
• To turn on the an

ti-glare feature, press the | button on the rearview mirror. The
indicator light
will turn on.
PROGRAMING THE HOMELINK
® UNIVERSAL TRANSCEIVER: 1.
Position the handheld tr
ansceiver 1-3 in (2-8 cm) away from the HomeLink
surface, keeping the HomeLink indicator light in view.
2.


Press and hold the desir

ed HomeLink button and the handheld transmitter button
simultaneously until the HomeLink indicator light flashes slowly and then rapidly.
3.





Both butt

ons may be released when the indicator light flashes rapidly.
4.


Press and hold the pr

ogramed HomeLink button and observe the indicator light. A solid, continuous light indicates the programing is complete. If
the indicator light rapidly blinks for two seconds and then turns to a solid, continuous light, continue with steps for a rolling code device.
5.


At the r

eceiver located on the garage door opener motor, locate the “learn” or “smart” button. If there is difficulty locating the button, reference the
garage door opener’s manual. Once the button is pressed, you have approximately 30 seconds to initiate the next step.
6.


Press and hold the pr

ogramed HomeLink button for two seconds and release. Repeat the sequence up to three times to complete the programing
process. HomeLink should now activate your rolling code equipped device.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
Automatic Anti-Glare Rearview Mirror with HomeLink® Universal
Transceiver (if so equipped)
HomeLink

14
Fuel-filler Door
Passenger Rear Seat Entry/Exit
To access the rear seat:
1. Pull the lev
er
upward to
fold the seatback forward.
2. Press the butt

on
to
slide the front seat forward
and press the button

again to stop the seat.
To return the front seat to its
original position:
1. Pull the lev

er
upward and push the seatback to the locked,
upright position.
2. Press the butt

on
to slide the front seat backward.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
To open the fuel-filler door,
unlock the vehicle and gently
push the upper left side of
the
fuel-filler

door.
Please see your Owner’s Manual for
important safety information, system
limitations, and additional operating
and feature information.
To adjust the time and the appearance of the clock
on the display:
1. Pr
ess the MENU button
below the lower display. Then,
touch the “Settings” key on the lower display.
2. Loc

ate and touch the “Clock” key to adjust “On-Screen
Clock”, “Daylight Savings Time”, “Clock Format (24h)”
and “Time Zone”.
Please see your INFINITI InTouch™ Owner’s Manual for important safety information,
system limitations, and additional operating and feature information.
Clock Set/Adjustment