wheel INFINITI Q70 2014 Owner's Guide

Black plate (113,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
Y51D-V-E01-87CEAEB1-8B39-4156-9CAE-F0F804171559
SIC4332
To sound the horn, push the center pad
area of the steering wheel.
WARNING
Do not disassemble the horn. Doing so
could affect proper operation of the supple-
mental front air bag system. Tampering with
the supplemental front air bag system may
result in serious personal injury.
Y51D-V-E01-E57CAE87-BC9D-4A04-8415-C2C0B200E402
WARNING
Do not use or allow occupants to use the
seat heater if you or the occupants can not
monitor elevated seat temperatures or have
an inability to feel pain in those body parts
in contact with the seat. Use of the seat
heater by such people could result in
serious injury.
CAUTION
.The battery could run down if the seat
heater is operated while the engine is
not running.
. Do not use the seat heater for extended
periods or when no one is using the
seat.
. Do not put anything on the seat which
insulates heat, such as a blanket,
cushion, seat cover, etc. Otherwise, the
seat may become overheated.
. Do not place anything hard or heavy on
the seat or pierce it with a pin or similar
object. This may result in damage to the
heater. .
Any liquid spilled on the heated seat
should be removed immediately with a
dry cloth.
. When cleaning the seat, never use
gasoline, thinner, or any similar materi-
als.
. If any malfunctions are found or the
heated seat does not operate, turn the
switch off and have the system checked
by an INFINITI retailer.
Instruments and controls2-41
HORN HEATED SEATS
Condition:

Black plate (117,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
Y51D-V-E01-3AEA4C41-CB09-4DCF-8036-823AE6B4A697
SIC4336
The vehicle should be driven with the
Vehicle Dynamic Control (VDC) system on
for most driving conditions.
If the vehicle is stuck in mud or snow, the
VDC system reduces the engine output to
reduce wheel spin. The engine speed will
be reduced even if the accelerator is
depressed to the floor. If maximum engine
power is needed to free a stuck vehicle,
turn the VDC system off.
To turn off the VDC system, push the VDC
OFF switch. The
indicator light will
illuminate.
Push the VDC OFF switch again or restart
the engine to turn on the system. (See “Vehicle Dynamic Control (VDC) system”
(P.5-102).)
Y51D-V-E01-45493C10-3BA4-49EC-9DCE-41E4ED9EED08
SIC4338
If the power supply is disconnected, the
clock will not indicate the correct time.
Readjust the time.
ADJUSTING THE TIMEY51D-V-E01-E5BD8934-435C-40FF-97E1-AD088819A5C51.
To set the clock forward, push the
button
*1.
2. To set the clock backward, push the button
*2.
3. To move forward or backward faster, push and hold the button more than 5
seconds.
For details about display clock adjustment
(if so equipped), see “How to use SETTING
button” (P.4-16).
Instruments and controls2-45
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH CLOCK
Condition:

Black plate (143,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
CAUTION
.Be sure to carry the Intelligent Key with
you when operating the vehicle.
. Never leave the Intelligent Key in the
vehicle when you leave the vehicle.
The Intelligent Key is always communicat-
ing with the vehicle as it receives radio
waves. The Intelligent Key system trans-
mits weak radio waves. Environmental
conditions may interfere with the operation
of the Intelligent Key system under the
following operating conditions.
.When operating near a location where
strong radio waves are transmitted,
such as a TV tower, power station and
broadcasting station.
. When in possession of wireless equip-
ment, such as a cellular telephone,
transceiver, and CB radio.
. When the Intelligent Key is in contact
with or covered by metallic materials.
. When any type of radio wave remote
control is used nearby.
. When the Intelligent Key is placed near
an electric appliance such as a perso- nal computer.
. When the vehicle is parked near a
parking meter.
In such cases, correct the operating condi-
tions before using the Intelligent Key
function or use the mechanical key.
Although the life of the battery varies
depending on the operating conditions,
the battery’s life is approximately 2 years.
If the battery is discharged, replace it with
a new one.
Since the Intelligent Key is continuously
receiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and
personal computer, the battery life may
become shorter.
For information regarding replacement of a
battery, see “Intelligent Key battery repla-
cement” (P.8-30).
For models with a steering wheel lock
mechanism: Because the steering wheel is
locked electrically, unlocking the steering
wheel with the ignition switch in the LOCK
position is impossible when the vehicle
battery is completely discharged. Pay
special attention that the vehicle battery
is not completely discharged. As many as 4 Intelligent Keys can be
registered and used with one vehicle. For
information about the purchase and use of
additional Intelligent Keys, contact an
INFINITI retailer.
CAUTION
.
Do not allow the Intelligent Key, which
contains electrical components, to come
into contact with water or salt water.
This could affect the system function.
. Do not drop the Intelligent Key.
. Do not strike the Intelligent Key sharply
against another object.
. Do not change or modify the Intelligent
Key.
. Wetting may damage the Intelligent Key.
If the Intelligent Key gets wet, immedi-
ately wipe until it is completely dry.
. Do not place the Intelligent Key for an
extended period in an area where
temperatures exceed 1408F (608C).
. If the outside temperature is below 148F
(−108C), the battery of the Intelligent
Key may not function properly.
Pre-driving checks and adjustments3-7
Condition:

Black plate (159,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
3. Push the reset switch*Aon the right
side of the combination meter panel for
longer than 1 second to turn off the
LOOSE FUEL CAP warning after tighten-
ing the fuel cap.
Y51D-V-E01-CEBF8919-BACA-45A0-AD5E-D7C5C540A80F
WARNING
. Do not adjust the steering wheel while
driving. You could lose control of your
vehicle and cause an accident.
. Do not adjust the steering wheel any
closer to you than is necessary for
proper steering operation and comfort.
The driver’s air bag inflates with great
force. If you are unrestrained, leaning
forward, sitting sideways or out of
position in any way, you are at greater
risk of injury or death in a crash. You
may also receive serious or fatal injuries
from the air bag if you are up against it
when it inflates. Always sit back against
the seatback and as far away as practical
from the steering wheel. Always use the
seat belts.
SPA2737
ELECTRIC OPERATIONY51D-V-E01-043E9C43-1598-497B-B427-D478DD3E9E4C
Tilt or telescopic operationY51D-V-E01-2D699F18-28FA-4EF4-B7D7-12496FEE85FFMove the lever to adjust the steering wheel
up or down, forward or rearward to the
desired position.
Entry/Exit function operation:
GUID-CA441E56-2FD0-4540-A74C-DB510E9F7AE0The automatic drive positioner system will
make the steering wheel move up auto-
matically when the driver’s door is opened
with the ignition switch in the LOCK
position. This lets the driver get into and
out of the seat more easily.
For more information, see “Automatic drive
Pre-driving checks and adjustments3-23
TILT/TELESCOPIC STEERING
Condition:

Black plate (163,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
switch.
4. The outside mirror surface moves
downward.
When one of the following conditions has
occurred, the outside mirror surface will
return to its original position.
. The shift lever is moved to any position
other than R (Reverse).
. The outside mirror control switch is set
to the center position.
. The ignition switch is pushed to the OFF
position.
Automatic anti-glareGUID-91655C78-1391-4C73-AE8D-F7830B95A06EThe outside rearview mirrors are designed
so that its automatically change reflection
according to the intensity of the headlights
of the vehicle following you.
The anti-glare system will be automatically
turned on when you push the ignition
switch to the “ON”position.
SIC3869
VANITY MIRRORY51D-V-E01-9AE2DF89-3765-4965-AB82-63AC485FF71BTo use the front vanity mirror, pull down
the sun visor and pull up the cover.
Y51D-V-E01-E450D796-08F9-4562-8F47-BFC4EB16402BThe automatic drive positioner system has
four features:
.Entry/exit function
. Seat synchronization function
. Memory storage
. Setting memory function
ENTRY/EXIT FUNCTIONY51D-V-E01-34AC63B3-B54E-4551-9D60-0BA261F4A048This system is designed so that the driver’s
seat and steering column will automati-
cally move when the shift lever is in the P
(Park) position. This allows the driver to get
into and out of the driver’s seat more
easily.
The driver’s seat will slide backward and
the steering wheel will move up when the
driver’s door is opened with the ignition
switch in the LOCK position.
The driver’s seat and steering wheel will
return to the previous positions when the
ignition switch is pushed to the ACC
position.
The driver’s seat will not return to the
previous positions if the seat or steering
adjusting switch is operated when the seat
is at the exit position.
Pre-driving checks and adjustments3-27
AUTOMATIC DRIVE POSITIONER
Condition:

Black plate (164,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
3-28Pre-driving checks and adjustments
Cancel or activate entry/exit func-
tion
Y51D-V-E01-115CBE46-BE91-4686-ABD6-BC9952E15046The shift lever must be in the P (Park)
position with the ignition switch in the OFF
position.
The entry/exit function can be activated or
canceled by pressing and holding the SET
switch for more than 10 seconds.
The indicator lights on the memory
switches (1 and 2) will blink once when
the function is canceled, and the indicator
lights will blink twice when the function is
activated. Note that the indicator lights
may illuminate after 5 seconds while
holding the SET switch. This indicates
readiness for linking the Intelligent Key to
a stored memory position. Keep the SET
switch pressed for more than 10 seconds
to turn on or off the entry/exit function.
The entry/exit function can also be acti-
vated or canceled if the“Lift Steering
Wheel on Exit” key or“Slide Driver Seat
Back on Exit” key is turned to ON or OFF in
the “Comfort settings” settings. (See“Ve-
hicle information and settings” (P.4-10).)
Initialize entry/exit functionY51D-V-E01-BC9F8DD7-6ABF-4E49-BF93-F0A27D40B9E9If the battery cable is disconnected, or if
the fuse opens, the entry/exit function will
not work though this function was set on
before. In such a case, after connecting the
battery or replacing with a new fuse, open
and close the driver’s door more than two
times after the ignition switch is turned
from the ON position to the LOCK position.
The entry/exit function will be activated.
JVP0241X
SEAT SYNCHRONIZATION FUNCTIONY51D-V-E01-D911BEBD-6096-44D1-85CC-1FF7231C5236The seat synchronization function automa-
tically adjusts the positions of the steering
wheel and outside mirrors when the seat is
adjusted using the power seat switches.
However, the steering wheel and outside
mirrors will not move if the seat is adjusted
over the maximum thresholds. The system
considers that the steering wheel and
outside mirror adjustments are not neces-
sary because the seat may not be adjusted
for the driving position. Note that the
function is set to disabled as the factory
default setting.
Condition:

Black plate (165,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
The seat synchronization function operates
under the following conditions:
.The ignition switch is in the ON posi-
tion.
. The shift lever is in the P (Park)
position.
If the outside mirrors or the steering wheel
reaches its maximum adjustment, the
function is automatically disabled. Restart
the function by selecting a previously
stored seat memory position using the
memory switches (1 or 2). An Intelligent
Key that was previously linked to the
stored seat memory can also be used to
restart the function.
If a seat position was not previously stored
in the seat memory, restart the function by
adjusting the steering wheel and outside
mirrors manually for your best driving
position and then drive the vehicle above
4 MPH (7 km/h).
Cancel or activate seat synchroni-
zation function
Y51D-V-E01-9F872CF3-250B-41E2-A6C8-B2FEC07B44D8The shift lever must be in the P (Park)
position with the ignition switch in the ACC
position.
MEMORY STORAGEY51D-V-E01-C3253FC6-067F-4EF6-AC8E-443DBC2A82D7Two positions for the driver’s seat, steering
column and outside mirrors can be stored
in the automatic drive positioner memory.
Follow these procedures to use the mem-
ory system.
1. Move the shift lever to the P (Park) position.
2. Adjust the driver’s seat, steering col- umn and outside mirrors to the desired
positions by manually operating each
adjusting switch. For additional infor-
mation, see “Seats”(P.1-2),“Tilt/tele-
scopic steering” (P.3-23) and“Outside
mirrors” (P.3-25).
3. Push the SET switch and, within 5
seconds, push the memory switch (1
or 2) fully for at least 1 second.
The indicator light for the pushed
memory switch will stay on for approxi-
mately 5 seconds after pushing the
switch.
When the memory is stored in the
memory switch (1 or 2), a buzzer will
sound.
If memory is stored in the same
memory switch, the previous memory
will be deleted.
Linking Intelligent Key to a stored
memory position
Y51D-V-E01-AB3F7AAC-59C4-4119-9D25-7D847B211DA2The Intelligent Key can be linked to a
stored memory position with the following
procedure.
1. Follow the steps for storing a memory
position.
2. While the indicator light for the memory switch being set is illuminated for 5
seconds, push the
button on the
Intelligent Key. If the indicator light
blinks, the Intelligent Key is linked to
that memory setting.
Push the ignition switch to the OFF posi-
tion, and then push the
button on the
Intelligent Key. The driver’s seat, steering
wheel and outside mirrors will move to the
memorized position.
Confirming memory storageY51D-V-E01-CE2091ED-9082-42A3-AC8C-4E5B88DA32AD. Push the ignition switch to the ON
position and push the SET switch. If
the main memory has not been stored,
the indicator light will come on for
approximately 0.5 second. When the
memory has stored in position, the
indicator light will stay on for approxi-
mately 5 seconds.
Pre-driving checks and adjustments3-29
Condition:

Black plate (166,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
3-30Pre-driving checks and adjustments
.If the battery cable is disconnected, or if
the fuse opens, the memory will be
canceled. In this case, reset the desired
position using the previous procedure.
. If optional Intelligent Keys are added to
your vehicle, the memory storage pro-
cedure to switch 1 or 2 and linking
Intelligent Key procedure to a stored
memory position should be performed
again for each Intelligent Key. For
additional Intelligent Key information,
see “Keys” (P.3-2).
Selecting the memorized positionY51D-V-E01-812ACCF7-5E50-4166-B150-60EB8EB9A5491. Move the shift lever to the P (Park)
position.
2. Use one of the following methods to move the driver’s seat, the outside
mirrors and the steering wheel.
.Push the memory switch (1 or 2)fully for at least 1 second.
.Within 45 seconds of opening the
driver’s door, push the memory
switch (1 or 2) fully for at least 1
second.
The driver’s seat, steering column
and outside mirrors will move to the
memorized position with the indica-
tor light flashing, and then the light
will stay on for approximately 5 seconds.
SETTING MEMORY FUNCTIONY51D-V-E01-44B080FA-3BF4-40E6-BD28-59C043780273The status of the following settings can be
linked to the Intelligent Key and the
memorized settings can be available for
each Intelligent Key.
.
Climate control system
. Navigation system (if so equipped)
. Audio system
To use the memory function, lock the doors
with the Intelligent Key that is linked to the
settings.
To enable the memorized settings:
1. Carry the Intelligent Key that is linked to the settings, and unlock the doors by
pushing the driver’s door handle re-
quest switch or UNLOCK
button on
the Intelligent Key.
2. Push the ignition switch to the “ON”
position. “Connection with the key has
been done” will be displayed on the
screen and the memorized settings are
available (only when a new Intelligent
Key is used).
SYSTEM OPERATIONY51D-V-E01-4CE0BF2D-D72F-4384-A8B7-B5B43A28A6A7The automatic drive positioner system will
not work or will stop operating under the
following conditions:
. When the vehicle speed is above 4 MPH
(7 km/h).
. When the adjusting switch for the
driver’s seat and steering column is
turned on while the automatic drive
positioner is operating.
. When the memory switch 1 or 2 is not
pushed for at least 1 second.
. When the seat, steering column and
outside mirrors have already been
moved to the memorized position.
. When no position is stored in the
memory switch.
. When the engine is started while
moving the automatic drive positioner.
. When the shift lever is moved from the
P (Park) position to any other position.
(However, it will not be canceled if the
switch is pushed while the seat and
steering column are returning to the
previous positions (entry/exit func-
tion).)
. When the driver’s door remains open
for more than 45 seconds and the
Condition:

Black plate (167,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
ignition switch is not in the ON posi-
tion.
. The seat synchronization function is
automatically disabled if the outside
mirrors or steering wheel reaches its
maximum adjustment.
. The seat synchronization function will
not operate if the seat is adjusted over
one of the following maximum thresh-
olds:
— Seat sliding: 3.0 in (76 mm)
— Seatback reclining: 9.1 degrees
— Seat lifter (rear side): 0.8 in (20 mm)
Pre-driving checks and adjustments3-31
Condition:

Black plate (169,1)
[ Edit: 2013/ 10/ 21 Model: Y51-D ]
4 Monitor, climate, audio, phone and voice recogni-tion systems
Safety note ...
.......................................................... 4-3
Center multi-function control panel ...
...................... 4-4
How to use INFINITI controller ...
.......................... 4-6
How to use touch screen (models with
navigation system) ...
.......................................... 4-6
Menu options (models with
navigation system) ...
.......................................... 4-8
How to select menus on the screen ...
................. 4-9
Vehicle information and settings ...
........................ 4-10
How to use STATUS button ...
............................ 4-10
How to use brightness control and display
ON/OFF button ...
.............................................. 4-10
How to use DISP button ...
................................ 4-10
How to use ECON button (models without
navigation system) ...
........................................ 4-10
How to use INFO button ...
................................ 4-10
How to use SETTING button ...
........................... 4-16
RearView monitor ...
.............................................. 4-26
How to read displayed lines ...
.......................... 4-27
How to park with predictive course lines ...
....... 4-28
Difference between predictive and
actual distances ...
............................................ 4-29
Predictive course line settings ...
....................... 4-32
How to adjust screen ...
.................................... 4-32
Sonar indicator (if so equipped) ...
.................... 4-33 Operating tips
...
.............................................. 4-33
Ventilators ...
........................................................ 4-33
Automatic climate control ...
.................................. 4-34
Automatic climate control (Type A) ...
............... 4-37
Automatic climate control (Type B) ...
............... 4-41
Forest Air
®(if so equipped) ...
......................... 4-43
Operating tips ...
.............................................. 4-47
Linking Intelligent Key ...
................................. 4-48
In-cabin microfilter ...
....................................... 4-48
Servicing climate control ...
.............................. 4-48
Audio system ...
.................................................... 4-49
Audio operation precautions ...
........................ 4-49
FM-AM-SAT radio with Compact Disc
(CD) player ...
................................................... 4-62
DVD (Digital Versatile Disc) player operation
(models with navigation system) ...
.................. 4-66
USB input operation ...
.................................... 4-69
Bluetooth
®streaming audio (models with
navigation system) ...
....................................... 4-74
iPod
®player operation ...
................................ 4-79
CD/DVD/USB memory care and cleaning ...
...... 4-81
Steering-wheel-mounted controls
for audio ...
..................................................... 4-82
Antenna ...
....................................................... 4-83
Car phone or CB radio ...
...................................... 4-84
Condition: