light INFINITI Q70 2014 Quick Reference Guide

15
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a
constant cruising speed once the vehicle has reached
25 MP
h (40 km/h).
The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.
To activate the cruise control, push the ON/OFF
switch
01 . The
CRUISE
indicator light in the

instrument panel will illuminate.
To set cruising speed, accelerate the vehicle to the desired speed, push\
the COAS t /SE t
switch
02 and release. The
CRUISE SE
t indicator light
in the instrument panel will

illuminate. Take your foot off the accelerator pedal. Your vehicle will \
maintain the set speed.
To reset at a faster cruising speed, push and hold the ACCEL/RES switch
03 . when the
vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the COAS t /SE t switch
02. Release the
switch when the vehicle slows to the desired speed.
To cancel the preset speed, push the CANCEL switch
04 .
To turn off cruise control, push the ON/OFF switch
01 . Both the CRUISE indicator light and
the SE
t
indicator light in the instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
03
02
04
USB/iPod® Interface
The USB jack 01 is located in the center console under

the arm rest.
w hen a compatible USB memory device or iPod® is

plugged into the USB jack, compatible audio and
video files stored on the device can be played
through the vehicle’s audio system and
front display.
For more information, refer to the “Monitor, climate, audio, phone
and voice recognition systems (section 4)” of your Owner’s Manual.
01
1276460_14a_Infiniti_Q70_QRG_102813.indd 1510/28/13 2:31 PM

16
first drive features
Intelligent Cruise Control (ICC) System (if so equipped)
vEhICLE-TO-vEhICLE dISTANCE CONTROL MOdE
To set v ehicle-To- v ehicle d istance Control mode,



press the
CRUISE ON/OFF button
01 for less than
1.5 seconds. The
CRUISE indicator light
02
will illuminate.
Accelerate to the desired speed.
Push down on the COAS t /SE t switch
03 and release
it. Cruise control will be set to the desired speed.
Press the distance button 04 repeatedly to change

the set distance between long, middle and short.
w hen a vehicle is not detected ahead of you in the



lane, the set distance, and set vehicle speed indicator




lights will illuminate 05 in set mode.

w hen a vehicle is detected ahead of you in the lane, the vehicle ahead
detection, set distance and set vehicle speed indicator lights will
illuminate
06 in set mode.
To reset at a faster cruising speed, push and hold the
ACCEL/RES switch
07 . when the vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the
COAS t /SE t switch
03 . Release



the switch when the vehicle slows to the desired speed.
To cancel the preset speed, push the CANCEL switch
08 or tap the brake pedal. The set
vehicle speed indicator 05 will extinguish.
To turn off cruise control, press the
CRUISE ON/OFF button
01 . The CRUISE indicator light

02 in the instrument panel will extinguish.
To set conventional (fixed speed) cruise control mode:
w hile cruise control is off, press the CRUISE ON/OFF
button
01 and hold it down for more
than 1.5 seconds. The CRUISE
indicator light will illuminate.
Accelerate to the desired speed.
Push down on the
COAS t /SE t switch and release it. The SE t indicator light will illuminate.



Cruise control should be set to the desired speed.
To switch between the two cruise control modes:
w hen one of the two cruise modes is in use, you must turn the system off \
and then turn it on



again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
0205
06
0807
03
01
04
1276460_14a_Infiniti_Q70_QRG_102813.indd 1610/28/13 2:31 PM

21
Navigation System (if so equipped)
01 Touch screen display.
02 d estination
(DES t ) – Press to enter a destination.
03 Information
(INFO) – Press to display the vehicle, traffic (if so equipped), weather
(if so equipped) or voice recognition information.
04 SE tt ING – Press to access the system settings.
05 Infiniti Controller


• EN t ER – Press the EN t ER button to select the highlighted item on the screen.
•

Center
Dial – Turn the dial to highlight an item on the screen, adjust a setting or adjust the

map scale.


•
Slide
the controller (push upward/downward/leftward/rightward) to select an item on the

screen, to adjust a setting or scroll the map in eight directions.
06 ROU t E – Press to access guidance control functions, such as guidance cance\
llation, route

priority or waypoint setting on the route.
07 MAP – Press to display the map. w hile following a programmed route, press multiple times
to change the type of route information.
0203
05
04
0908
1110
0706
01
1276460_14a_Infiniti_Q70_QRG_102813.indd 2110/28/13 2:31 PM

23

HomeLink® Universal Transceiver (if so equipped)
The h omeLink system can learn and consolidate the functions of up to 3 differ\
ent
hand-held transmitters, operating items such as garage doors, property g\
ates, outdoor and
indoor lights or alarm systems.
To program the h omeLink® Universal Transceiver:
•

Position


the

handheld

transceiver 1-3 in (26-76 mm) away from the HomeLink surface,
keeping the
h
omeLink indicator light in view.
•

Press


and

hold

the

desired HomeLink button and the handheld transmitter button
simultaneously until the
h omeLink indicator light flashes slowly and then rapidly.
•

Both


buttons

may

be

released when the indicator light flashes rapidly.
To verify the programming is complete, press and hold the h omeLink button and observe
the indicator light:
•

A
solid continuous light indicates the programming is complete, and the HomeLink button

will activate your device.


•
A
blinking light that turns to a solid continuous light after 2 seconds indicates additional
steps are required to complete the programming.
An additional person may make the remaining steps easier. To complete th\
e
programming process:
•

At
the receiver of the device that you are programming to the HomeLink button, press

and release the learn or smart button (the name may vary by manufacture\
r, but it is


usually located near where the hanging antenna wire is attached to the u\
nit). You have
approximately 30 seconds to initiate the following step.
•

Press
and hold the programed HomeLink button for 2 seconds and release.
You may have to repeat the previous 2 steps up to 3 times to complete th\
e programing
process.
h omeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the homeLink website at
www.homelink.com or call
1-800-355-3515.
HOMELINK
1276460_14a_Infiniti_Q70_QRG_102813.indd 2310/28/13 2:32 PM