ABS INFINITI QX30 2017 User Guide

Wheels and Tiresin the9. Maintenance and
Schedules section.)
– For detailed information, see Wheels and
tires in the 8. Do-it-yourself section.
The Anti-lock Braking System (ABS) controls the
brakes so the wheels do not lock during hard
braking or when braking on slippery surfaces.
The system detects the rotation speed at each
wheel and varies the brake fluid pressure to
prevent each wheel from locking and sliding. By
preventing each wheel from locking, the system
helps the driver maintain steering control and
helps to minimize swerving and spinning on
slippery surfaces.
Using system
Depress the brake pedal and hold it down.
Depress the brake pedal with firm steady pres-
sure, but do not pump the brakes. The ABS will
operate to prevent the wheels from locking up.
Steer the vehicle to avoid obstacles.
WARNING
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer.
The computer has a built-in diagnostic feature
that tests the system each time you start the
engine and move the vehicle at a low speed in
forward or reverse. When the self-test occurs,
you may hear a “clunk” noise and/or feel a
pulsation in the brake pedal. This is normal and
does not indicate a malfunction. If the computer
senses a malfunction, it switches the ABS off
and illuminates the ABS warning light on the
instrument panel. The brake system then oper-
ates normally, but without anti-lock assistance.
If the ABS warning light illuminates during the
self-test or while driving, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
Normal operation
The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according to
road conditions.
When the ABS senses that one or more wheels
are close to locking up, the actuator rapidly
applies and releases hydraulic pressure. This
action is similar to pumping the brakes very
quickly. You may feel a pulsation in the brake
pedal and hear a noise from under the hood or
feel a vibration from the actuator when it is
operating. This is normal and indicates that the
ABS is operating properly. However, the pulsa-
tion may indicate that road conditions are haz-
ardous and extra care is required while driving.
Starting and driving5-89

The Vehicle Dynamic Control (VDC) system uses
various sensors to monitor driver inputs and
vehicle motion. Under certain driving condi-
tions, the VDC system helps to perform the
following functions.
•Controls brake pressure to reduce wheel slip
on one slipping drive wheel so power is
transferred to a non slipping drive wheel on
the same axle.
•Controls brake pressure and engine output
to reduce drive wheel slip based on vehicle
speed (traction control function).
•Controls brake pressure at individual wheels
and engine output to help the driver maintain
control of the vehicle in the following condi-
tions:– understeer (vehicle tends to not follow the steered path despite increased steering
input)
– oversteer (vehicle tends to spin due to certain road or driving conditions).
The VDC system can help the driver to maintain
control of the vehicle, but it cannot prevent loss
of vehicle control in all driving situations. When the VDC system operates, the VDC warn-
ing light in the instrument panel flashes so note
the following:
•The road may be slippery or the system may
determine some action is required to help
keep the vehicle on the steered path.
•You may feel a pulsation in the brake pedal
and hear a noise or vibration from under the
hood. This is normal and indicates that the
VDC system is working properly.
•Adjust your speed and driving to the road
conditions.
See Vehicle Dynamic Control (VDC) warning
light in the 2. Instruments and controls sec-
tion.
If a malfunction occurs in the system, the VDC
warning light
illuminates in the instrument
panel. The VDC system automatically turns off.
WARNING
•The VDC system is designed to help the
driver maintain stability but does not pre-
vent accidents due to abrupt steering opera-
tion at high speeds or by careless or danger-
ous driving techniques. Reduce vehicle
speed and be especially careful when driv- ing and cornering on slippery surfaces and
always drive carefully.
•Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings
and wheels are not INFINITI recommended
for your vehicle or are extremely deterio-
rated, the VDC system may not operate
properly. This could adversely affect vehicle
handling performance, and the VDC warning
light
may illuminate.
•If brake related parts such as brake pads,
rotors and calipers are not INFINITI recom-
mended or are extremely deteriorated, the
VDC system may not operate properly and
the VDC warning light
may illuminate.
•If engine control related parts are not
INFINITI recommended or are extremely de-
teriorated, the VDC warning light
may
illuminate.
•When driving on extremely inclined sur-
faces such as higher banked corners, the
VDC system may not operate properly and
the VDC warning light
may illuminate.
Do not drive on these types of roads.
•When driving on an unstable surface such
as a turntable, ferry, elevator or ramp, the
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
5-90Starting and driving

GENUINE LEATHER SEAT COVERS
Automotive leather is typically finished with
coatings which protect the surface from the
sun’s damaging rays as well as making it
resistant to soiling. The finishes used in auto-
motive upholstery are unique; very different to
furniture, garment or shoe leathers. Leather is
extremely resilient and easy to clean and main-
tain.
•Before cleaning leather upholstery, vacuum
it to remove dust.
•To clean leather, simply use a soft and
lint-free cloth dampened with lukewarm wa-
ter and mild soap. Do not soak the leather.
•Use a gentle, circular motion. Do not run the
leather or apply extreme pressure when
cleaning.
•Wipe the leather again with another clean,
slightly damp cloth to remove soap residue.
Dry with a soft cloth.
Leather should be cleaned whenever it becomes
soiled. Dust and dirt may harm leather if al-
lowed to work into the finish.
Never use alcohol, cleaning solvents, oils, var-
nishes or polishes on your leather, and avoid
using unknown products as they damage the finish. Only use leather care agents approved
by INFINITI.
Steaming or ironing is not recommended as it
may damage the leather.
Leather is a natural product and has natural
surface properties such as unevenness in struc-
ture, marks caused by injury, and subtle color
differences. These are characteristics of leather
and not material faults.
Leather cleaning kit (if equipped)
Spray onto the leather cleaning cloth, then
gently wipe the surface of leather. Use a dry
towel to absorb any excess moisture.
Please refer to the instruction manual provided
with the leather cleaner kit.
Clean light-colored leather more frequently be-
cause soiling on such surfaces is much more
visible.
You can obtain the leather cleaner kit from an
INFINITI retailer.
MOST COMMON FACTORS
CONTRIBUTING TO VEHICLE
CORROSION
Most vehicle corrosion is caused by:
•The accumulation of moisture-retaining dirt
and debris in body panel sections, cavities,
and other areas.
•Damage to the paint surface and other pro-
tective coatings caused by gravel and stone
chips or minor traffic accidents.
ENVIRONMENTAL FACTORS INFLUENCE
THE RATE OF CORROSION
Moisture
The accumulation of sand, dirt and water on the
inside floor of the vehicle can accelerate corro-
sion. Wet floor carpet/floor mats will not dry
completely inside the vehicle. They should be
removed and completely dried to avoid floor
panel corrosion.
Relative humidity
Corrosion will be accelerated in areas of high
relative humidity, especially those areas where
the temperatures stay above freezing and
where atmospheric pollution exists and road
salt is used.
CORROSION PROTECTION
7-6Appearance and care

4. Repeatedly tap the key against your palmuntil battery
1falls out. 5. Insert the new battery with the positive
terminal facing upwards. Use a lint-free cloth
to do so.
6. Make sure that the surface of the battery is free of lint, grease and other contamination.
7. Insert the front tabs of battery cover
1and
then press to close it.
8. Insert emergency key element into the key (see Mechanical key in the3. Pre-driving
checks and adjustments section).
9. Check the function of all key buttons on the vehicle.
If you need assistance with replacement, it is
recommended that you visit an INFINITI retailer
for this service. FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
NPA1473SPA0784Z
Do-it-yourself8-21

Use the following steps to mount the front
license plate:Before mounting the license plate, confirm that
the following parts are enclosed in the plastic
bag:
Only use the recommended mounting position,
otherwise the obstruction of the IntelligentCruise Control (ICC) sensor (if so equipped) may
result.
•License plate bracket
•License plate screws x 2
•Screw grommets x 2
1) Park the vehicle on flat, level ground.
2) Locate the center position
Aas illustrated.
Line up the license plate bracket under the
top of the front bumper with the tabs
B.
Hold the license plate bracket in place.
3) Mark the center of the holes
Cwith a
felt-tip pen.
4) Carefully drill two pilot holes using a 10 mm (0.39 in) drill bit at the marked locations. (Be
sure that the drill only goes through the bum-
per fascia.)
5) Insert the grommets into the holes in the bumper fascia.
6) Install the license plate bracket with the provided screws.
7) Install the license plate on to the bracket with bolts that are no longer than 14 mm
(0.55 in).
NTI327
INSTALLING FRONT LICENSE PLATE
10-12Technical information

11 Index
ABS (Anti-lock Braking System).........2-9
Warninglight .................2-9
Active sound enhancement ..........5-67
Operation ...................5-67
Adaptive Front lighting System ........2-65
Aids .......................5-60 Forward emergency braking system ....5-60
Hill Start Assist (HSA) ............5-93
Intelligent Parking Assist (IPA) .......5-68
Air bags .....................1-47
Front passenger air bag switch .......1-47
Overview ....................0-2
Repair and replacement ...........1-56
Supplemental Restraint System ......1-38
Warninglight..............1-55, 2-12
Air cleaner filter .................8-13
Air conditioner .................4-42
Heater and air conditioner .........4-42
Refrigerant and lubricant ..........10-6
Servicing ...................4-51
Specification label .............10-11
Airfresheners...................7-4
Anti-theft alarm system ............2-58
AppGarage...................4-98 Screen ....................4-98
Settings screen ...............4-99
Around View Monitor ..............4-24
Moving object detection (MOD) ......4-37Settings
....................4-33
Audible reminders ................2-14
Audio .......................4-52
Operation precautions ...........4-52
Settings ...................4-80
Sourcebar..................4-65
System ....................4-52
Automatic transmission .............8-7
Fluid(ATF)...................8-7
Operation ...................5-18
Battery ......................8-9
Cautionlabel .................8-9
Coldweather.................5-93
Jump-starting .................6-10
Replacement - Intelligent Key .......8-20
Saver system ................2-86
Vehicle battery ................8-10
Blind Spot Warning (BSW) system ......5-35
Bluetooth®...................4-83 Hands-Free Phone System .....4-83,4-131
Information..................4-96
Streamingaudio..............4 -130
Booster seats ..................1-35
Precautions................. .1-35
B r

akes......................8-17 ABS (Anti-Lock Braking System) ......5-88
Adjustment..................8-17 Fluid ......................8-7
Forward emergency braking system
....5-60
Parking brake ................5-25
Precautions ..................5-87
System ....................5-87
Warninglight .................2-9
Break-inschedule................5-81
Brightness....................2-69 Instrumentpanel ..............2-69
Capacities and recommendations .......10-2
Coolant....................10-2
Fuel......................10-2
Oil.......................10-2
Refrigerant ..................10-2
Cardholder...................2-79
Center multi-function control panel ......4-2
Changing.....................8-4 Enginecoolant ................8-4
Engineoil ...................8-5
Engine oil filter ................8-6
Tires and wheels ..............8-32
Checking .....................8-4
Coolantlevel .................8-4
Engine oil level ................8-5
Child restraints .................1-20
Anchorage ..................1-23
ISOFIX installation ..............1-23