INFINITI QX30 2017 Owner's Manual

being pulled, use the recovery hook stored in
the vehicle trunk.
WARNING
•Use the recovery hook only. Do not attach
the pulling device to any other part of the
vehicle body. Otherwise, the vehicle body
may be damaged.
•Use the recovery hook to free a vehicle only.
Never tow a vehicle using only the recovery
hook.
•The recovery hook is under tremendous
stress when used to free a trapped vehicle.
Always pull the pulling device straight out
from the vehicle. Never pull on the recovery
hook at an angle.
Securely install the recovery hook (stored in the
vehicle trunk) to the attaching mount located on
the front or rear bumper.
Make sure that the recovery hook is properly
secured in its storage location after use and the
license plate is properly reinstalled before driv-
ing the vehicle.
Rocking a stuck vehicle
WARNING
•To avoid potential injury, stand clear of a
stuck vehicle.
•Do not spin your tires at high speed. This
could cause them to explode and result in
serious injury. Parts of your vehicle could
also overheat and be damaged.
If your vehicle is stuck in sand, snow, mud, etc.,
use the following procedure:
1. Turn off the Vehicle Dynamic Control (VDC) system.
2. Make sure the area in front and behind the vehicle is clear of obstructions.
3. Turn the steering wheel right and left to clear an area around the front tires.
4. Slowly rock the vehicle forward and back- ward.
•Shift back and forth between R (Reverse) and
D (Drive).
•Apply the accelerator as little as possible to
maintain the rocking motion.
•Release the accelerator pedal before shifting
between R (Reverse) and D (Drive).
•Do not spin the tires above 35 MPH (55
km/h).
5. If the vehicle cannot be freed after a few tries, contact a professional towing service
to remove the vehicle.
6-16In case of emergency

7 Appearance and care
Cleaning exterior...................... .7-2
Washing ..........................7-2
Waxing .......................... .7-2
Removing spots ..................... .7-3
Underbody .........................7-3
Glass ........................... .7-3
Wheels .......................... .7-3
Aluminum alloy wheels ..................7-3
Chrome parts ...................... .7-3
Tire dressings ...................... .7-4
Cleaning interior ....................... .7-4Air fresheners
...................... .7-4
Floor mats (if equipped) .................7-5
Seat belts ..........................7-5
Cleaning the seat tracks .................7-5
Genuine leather seat covers ..............7-6
Corrosion protection .................... .7-6
Most common factors contributing to vehicle
corrosion ..........................7-6
Environmental factors influence the rate of
corrosion ..........................7-6
To protect your vehicle from corrosion ........7-7

In order to maintain the appearance of your
vehicle, it is important to take proper care of it.
To protect the paint surfaces, please wash your
vehicle as soon as you can:
•After a rainfall, to prevent possible damage
from acid rain.
•After driving on coastal roads.
•When contaminants such as soot, bird drop-
pings, tree sap, metal particles or bugs get
on the paint surface.
•When dust or mud builds up on the surface.
Whenever possible, park your vehicle inside a
garage or in a covered area to minimize the
chances of damaging the paint surface of your
vehicle.
When it is necessary to park outside, park in a
shady area or protect the vehicle with a body
cover. Be careful not to scratch the paint surface
when putting on or removing the body cover.
WASHING
Wash dirt off with a wet sponge and plenty of
water. Clean the vehicle thoroughly using a mild
soap, a special vehicle soap or general purpose
dishwashing liquid mixed with clean, lukewarm
(never hot) water.
CAUTION
•Do not use car washes that use acid in the
detergent. Some car washes, especially
brushless ones, use some acid for cleaning.
The acid may react with some plastic vehicle
components, causing them to crack. This
could affect their appearance, and also
could cause them not to function properly.
Always check with your car wash to confirm
that acid is not used.
•Do not wash the vehicle with strong house-
hold soap, strong chemical detergents,
gasoline or solvents.
•Do not wash the vehicle in direct sunlight or
while the vehicle body is hot, as the paint
surface may become water-spotted.
•Avoid using tight-napped or rough cloths,
such as washing mitts. Care must be taken
when removing caked-on dirt or other for-
eign substances so the paint surface is not
scratched or damaged.
Rinse the vehicle thoroughly with plenty of
clean water.
Inside edges, seams and folds on the doors,
hatches and hood are particularly vulnerable to
the effects of road salt. Therefore, these areas must be cleaned regularly. Take care that the
drain holes in the lower edge of the door are
open. Spray water under the body and in the
wheel wells to loosen the dirt and wash away
road salt.
A damp chamois can be used to dry the vehicle
to avoid water spots.
WAXING
Regular waxing protects the paint surface and
helps maintain a new vehicle appearance.
After waxing, polishing is recommended to re-
move built-up residue and to avoid a weathered
appearance.
An INFINITI retailer can assist you in choosing
the appropriate waxing products.
•Wax your vehicle only after a thorough wash-
ing. Follow the instructions supplied with the
wax.
•Do not use a wax containing any abrasives,
cutting compounds or cleaners that may
damage the vehicle finish.
Machine compounding or aggressive polishing
on a base coat/clear coat paint finish may dull
the finish or leave swirl marks.
CLEANING EXTERIOR
7-2Appearance and care

REMOVING SPOTS
Remove tar and oil spots, industrial dust, in-
sects, and tree sap as quickly as possible from
the paint surface to avoid lasting damage or
staining. Special cleaning products are avail-
able at an INFINITI retailer or any automotive
accessory store.
UNDERBODY
In areas where road salt is used in the winter, it
is necessary to clean the vehicle’s underbody
regularly in order to prevent dirt and salt from
building up and causing the acceleration of
corrosion on the underbody and suspension.
Before the winter and again in the spring, the
underseal must be checked and, if necessary,
re-treated.
GLASS
Use glass cleaner to remove smoke and dust
film from the glass surfaces. It is normal for
glass to become coated with a film after the
vehicle is parked in the hot sun. Glass cleaner
and a soft cloth will easily remove this film.
CAUTION
When cleaning the inside of the windows, do
not use sharp-edged tools, abrasive cleaners
or chlorine-based disinfectant cleaners. They
could damage the electrical conductors, radio
antenna elements or rear window defroster
elements.
WHEELS
•Wash the wheels when washing the vehicle
to maintain their appearance.
•Clean the inner side of the wheels when the
wheel is changed or the underside of the
vehicle is washed.
•Do not use abrasive cleaners when washing
the wheels.
•Inspect wheel rims regularly for dents or
corrosion. This may cause loss of pressure or
damage the tire bead.
•INFINITI recommends that the road wheels be
waxed to protect against road salt in areas
where it is used during winter.
ALUMINUM ALLOY WHEELS
Wash the wheels regularly with a sponge damp-
ened in a mild soap solution, especially during
winter in areas where road salt is used. The salt
residue from road salt could discolor the wheels
if it is not washed off regularly.
CAUTION
Follow the directions below to avoid staining
or discoloring the wheels:
•Do not use a cleaner that uses strong acid or
alkali contents to clean the wheels.
•Do not apply wheel cleaners to the wheels
when they are hot. The wheel temperature
should be the same as ambient tempera-
ture.
•Rinse the wheel to completely remove the
cleaner within 15 minutes after the cleaner
is applied.
CHROME PARTS
Clean all chrome parts regularly with a nonabra-
sive chrome polish to maintain the finish.
Appearance and care7-3

TIRE DRESSINGS
INFINITI does not recommend the use of tire
dressings. Tire manufacturers apply a coating
to the tires to help reduce discoloration of the
rubber. If a tire dressing is applied to the tires,
it may react with the coating and form a com-
pound. This compound may come off the tire
while driving and stain the vehicle paint.
If you choose to use a tire dressing, take the
following precautions:
•Use a water-based tire dressing. The coating
on the tire dissolves more easily than with an
oil-based tire dressing.
•Apply a light coat of tire dressing to help
prevent it from entering the tire tread/
grooves (where it would be difficult to re-
move).
•Wipe off excess tire dressing using a dry
towel. Make sure the tire dressing is com-
pletely removed from the tire tread/grooves.
•Allow the tire dressing to dry as recom-
mended by tire dressing manufacturer.Occasionally remove loose dust from the inte-
rior trim, plastic parts and seats using a vacuum
cleaner or soft bristled brush. Wipe the vinyl
and leather surfaces with a clean, soft cloth
dampened in mild soap solution, then wipe
clean with a dry, soft cloth.
Regular care and cleaning is required in order to
maintain the appearance of the leather.
Before using any fabric protector, read the
manufacturer’s recommendations. Some fabric
protectors contain chemicals that may stain or
bleach the seat material.
Use a soft cloth dampened only with water to
clean the meter and gauge lens covers.
WARNING
Do not use water or acidic cleaners (hot steam
cleaners) on the seat. This can damage the
seat or occupant classification sensor. This
can also affect the operation of the air bag
system and result in serious personal injury.
CAUTION
•Never use benzine, thinner or any similar
material on the interior surfaces or surface
damage may occur. Such damage is not cov-
ered under the INFINITI warranty.
•Small dirt particles can be abrasive and
damaging to leather surfaces and should be
removed promptly. Do not use saddle soap,
car waxes, polishes, oils, cleaning fluids,
solvents, detergents or ammonia-based
cleaners as they damage the leather’s natu-
ral finish.
•Never use fabric protectors unless recom-
mended by the manufacturer.
•Do not use glass or plastic cleaner on meter
or gauge lens covers. It may damage the
lens covers.
AIR FRESHENERS
Most air fresheners use a solvent that could
affect the vehicle interior. If you use an air
freshener, take the following precautions:
•Hanging-type air fresheners can cause per-
manent discoloration when they contact ve-
hicle interior surfaces. Place the air fresh-
ener in a location that allows it to hang free
and not contact an interior surface.
•Liquid-type air fresheners typically clip on
the ventilators. These products can cause
immediate damage and discoloration when
spilled on interior surfaces.
CLEANING INTERIOR
7-4Appearance and care

Carefully read and follow the manufacturer’s
instructions before using air fresheners.
FLOOR MATS (IF EQUIPPED)
WARNING
To avoid potential pedal interference that may
result in a collision, injury or death:
•NEVER place a floor mat on top of another
floor mat in the driver front position.
•It is recommended you use only genuine
INFINITI floor mats specifically designed for
use in your vehicle model. For additional
information, it is recommended you contact
an INFINITI retailer.
•Properly position the mats in the floorwell
using the floor mat positioning aid.
The use of genuine INFINITI floor mats can
extend the life of your vehicle carpet and make
it easier to clean the interior. Mats should be
maintained with regular cleaning and replaced
if they become excessively worn.
Floor mat positioning aid
This vehicle includes a front floor mat bracket to
act as a floor mat positioning aid. INFINITI floor
mats have been specially designed for your
vehicle model.
Position the mat by placing the floor mat
bracket hook through the floor mat grommet
hole while centring the mat in the foot area.
Periodically check that the mats are properly
positioned.
SEAT BELTS
The seat belts can be cleaned by wiping them
with a sponge dampened in a mild soap
solution. Allow the belts to dry completely in the shade
before using them. For additional information,
see
Seat belts in the1. Safety — seats, seat
belts and supplemental restraint system
section.
WARNING
•Do not allow wet seat belts to roll up in the
retractor.
•NEVER use bleach, dye or chemical solvents
to clean the seat belts, since these materi-
als may severely weaken the seat belt
webbing.
CLEANING THE SEAT TRACKS
CAUTION
Periodically clean the seat tracks to prevent
reduction of ability to move the seats.
Clean periodically with a high-powered
vacuum cleaner. Dirt and debris may reduce
the ability to adjust the seat. A wet cleansing
agent may be used if necessary.
SAI0039ZExample
Appearance and care7-5

GENUINE LEATHER SEAT COVERS
Automotive leather is typically finished with
coatings which protect the surface from the
sun’s damaging rays as well as making it
resistant to soiling. The finishes used in auto-
motive upholstery are unique; very different to
furniture, garment or shoe leathers. Leather is
extremely resilient and easy to clean and main-
tain.
•Before cleaning leather upholstery, vacuum
it to remove dust.
•To clean leather, simply use a soft and
lint-free cloth dampened with lukewarm wa-
ter and mild soap. Do not soak the leather.
•Use a gentle, circular motion. Do not run the
leather or apply extreme pressure when
cleaning.
•Wipe the leather again with another clean,
slightly damp cloth to remove soap residue.
Dry with a soft cloth.
Leather should be cleaned whenever it becomes
soiled. Dust and dirt may harm leather if al-
lowed to work into the finish.
Never use alcohol, cleaning solvents, oils, var-
nishes or polishes on your leather, and avoid
using unknown products as they damage the finish. Only use leather care agents approved
by INFINITI.
Steaming or ironing is not recommended as it
may damage the leather.
Leather is a natural product and has natural
surface properties such as unevenness in struc-
ture, marks caused by injury, and subtle color
differences. These are characteristics of leather
and not material faults.
Leather cleaning kit (if equipped)
Spray onto the leather cleaning cloth, then
gently wipe the surface of leather. Use a dry
towel to absorb any excess moisture.
Please refer to the instruction manual provided
with the leather cleaner kit.
Clean light-colored leather more frequently be-
cause soiling on such surfaces is much more
visible.
You can obtain the leather cleaner kit from an
INFINITI retailer.
MOST COMMON FACTORS
CONTRIBUTING TO VEHICLE
CORROSION
Most vehicle corrosion is caused by:
•The accumulation of moisture-retaining dirt
and debris in body panel sections, cavities,
and other areas.
•Damage to the paint surface and other pro-
tective coatings caused by gravel and stone
chips or minor traffic accidents.
ENVIRONMENTAL FACTORS INFLUENCE
THE RATE OF CORROSION
Moisture
The accumulation of sand, dirt and water on the
inside floor of the vehicle can accelerate corro-
sion. Wet floor carpet/floor mats will not dry
completely inside the vehicle. They should be
removed and completely dried to avoid floor
panel corrosion.
Relative humidity
Corrosion will be accelerated in areas of high
relative humidity, especially those areas where
the temperatures stay above freezing and
where atmospheric pollution exists and road
salt is used.
CORROSION PROTECTION
7-6Appearance and care

Temperature
High temperatures accelerate the rate of corro-
sion to those parts which are not well venti-
lated.
Air pollution
Industrial pollution, the presence of salt in the
air in coastal areas, or heavy road salt use
accelerates the corrosion process. Road salt
also accelerates the disintegration of paint sur-
faces.
TO PROTECT YOUR VEHICLE FROM
CORROSION
•Wash and wax your vehicle often to keep the
vehicle clean.
•Always check for minor damage to the paint
surface and repair it as soon as possible.
•Keep drain holes in the lower edge of the
doors open to avoid water accumulation.
•Check the underbody for accumulation of
sand, dirt or salt. If present, wash with water
as soon as possible.
CAUTION
•NEVER remove dirt, sand or other debris
from the passenger compartment by wash-
ing it out with a hose. Remove dirt with a
vacuum cleaner or broom.
•Never allow water or other liquids to come in
contact with electronic components inside
the vehicle as this may damage them.
Chemicals used for road surface deicing are
extremely corrosive. They accelerate corrosion
and deterioration of underbody components
such as the exhaust system, fuel and brake
lines, brake cables, floor pan and fenders.
In winter, the underbody must be cleaned peri-
odically.
For additional protection against rust and cor-
rosion, which may be required in some areas, it
is recommended that you visit an INFINITI re-
tailer.
Appearance and care7-7

NOTE
7-8Appearance and care

8 Do-it-yourself
Maintenance precautions..................8-2
Engine compartment check locations ...........8-3
2.0L Gasoline engine .................. .8-3
Engine cooling system ................... .8-3
Checking engine coolant level .............8-4
Changing engine coolant ................8-4
Engine oil ........................... .8-5
Checking engine oil level ................8-5
Changing engine oil .................. .8-5
Changing engine oil filter ................8-6
Automatic Transmission Fluid (ATF) ............8-7
Brake fluid .......................... .8-7
Window washer fluid .................... .8-8
Battery ............................ .8-9
Accessing Vehicle battery ...............8-10
Maintenance free battery ................8-10
Models with Idle Stop/Start System .........8-10
Battery replacement .................. .8-11
Reinitialisation procedure after battery
reconnection ...................... .8-12
Jump-starting ...................... .8-12
Drive belt .......................... .8-12
Spark plugs ..........................8-13
Air cleaner filter ...................... .8-13
Wiper blades .........................8-13 Cleaning
..........................8-13
Replacing front window wiper blades ........8-14
Replacing rear window wiper blade ..........8-15
Brakes ............................ .8-17
Self-adjusting brakes ..................8-17
Fuses ............................. .8-17
Before replacing a fuse .................8-17
Engine compartment .................. .8-17
Passenger compartment ................8-18
Intelligent key battery replacement ..........
.8-20
Checking the

battery ..................8-20
Replacing the battery ..................8-20
Lights ............................ .8-22
Exterior and interior lights ...............8-22
Replacement procedures ................8-24
Wheels and tires ..................... .8-26
Tire Pressure ...................... .8-26
Tire inflation pressure .................8-28
Tire labeling ...................... .8-28
Types of tires ..................... .8-30
Tire chains ....................... .8-31
Tire wear and damage .................8-31
Tire rotation ...................... .8-32
Replacing wheels and tires ..............8-32
Wheel balance ..................... .8-34