change time INFINITI QX30 2017 Service Manual

below 5 MPH (10 km/h). Otherwise, IPA will
be canceled.
7. Stop as soon as the parking sensor system sounds the continuous warning tone, if not
before. Maneuvering may be required in
tight parking spaces.
The [Park Assist active Select D Observe
surroundings] message appears in the ve-
hicle information display.
8. Select transmission position D (Drive) while the vehicle is stationary.
IPA immediately steers in the other direc-
tion.
The [Park Assist Observe surroundings] mes-
sage appears in the vehicle information dis-
play.
NOTE
You will achieve the best results by waiting
for the steering procedure to complete before
pulling away.
9. Drive forwards and be ready to brake at all times.
Maneuvering may be required in tight park-
ing spaces. Drive forward and back up as
prompted by the parking sensor system
warning displays, several times if necessary. 10. Stop as soon as the parking sensor system
sounds the continuous warning tone, if not
before.
The [Park Assist active Select R] [Observe
surroundings] message appears in the ve-
hicle information display.
As soon as the parking procedure is com-
plete the [Park Assist switched off] mes-
sage appears and a warning tone sounds.
The vehicle is now parked.
11. Before leaving the vehicle, secure the ve- hicle against rolling away unintentionally:
•The electric parking brake must be ap-
plied.
•The transmission must be in position P
(Park) and the transmission position dis-
play must show P in the vehicle informa-
tion display.
•The key must be removed from the igni-
tion switch.
•On uphill or downhill gradients, the front
wheels must be turned towards the curb.
IPA no longer supports you with steering inter-
ventions. When IPA is finished, you must steer
again yourself. The parking sensor system is
still available. Parking tips:
•The way your vehicle is positioned in the
parking space after parking is dependent on
various factors. These include the position
and shape of the vehicles parked in front and
behind it and the conditions of the location.
It may be the case that IPA guides you too far
into a parking space, or not far enough into
it. In some cases, it may also lead you across
or onto the curb. If necessary you should
cancel the parking procedure with IPA.
•During the parking maneuver, the system will
indicate when you should shift to R (Reverse)
or D (Drive). However, you can freely choose
to shift gear whenever you feel you need to.
Should the transmission change take place
too early, the parking procedure will be
canceled. A sensible parking position can no
longer be achieved from this position.
EXITING A PARKING SPACE
In order that IPA can support when exiting the
parking space:
•You need to have parked using IPA.
•The border of the parking space must be high
enough at the front and the rear. A curb
stone is too small, for example.
Starting and driving5-71

Brake pads/linings and rotors that are either
new or have been replaced only achieve opti-
mum braking effect after several hundred
miles of driving. Compensate for the reduced
braking effect by applying greater force to the
brake pedalFollow these easy-to-use Fuel Efficient Driving
Tips to help you achieve the most fuel economy
from your vehicle.
1.
Use Smooth Accelerator and Brake Pedal Ap-
plication
•Avoid rapid starts and stops.
•Use smooth, gentle accelerator and brake
application whenever possible.
•Maintain constant speed while commuting
and coast whenever possible.
2. Maintain Constant Speed
•Look ahead to try and anticipate and
minimize stops.
•Synchronizing your speed with traffic
lights allows you to reduce your number
of stops.
•Maintaining a steady speed can minimize
red light stops and improve fuel effi-
ciency.
3. Use Air Conditioning (A/C) at Higher Vehicle
Speeds
•Below 40 MPH (64 km/h), it is more
efficient to open windows to cool the
vehicle due to reduced engine load.
•Above 40 MPH (64 km/h), it is more
efficient to use A/C to cool the vehicle due
to increased aerodynamic drag.
•Recirculating the cool air in the cabin
when the A/C is on reduces cooling load.
4. Drive at Economical Speeds and Distances
•Observing the speed limit and not ex-
ceeding 60 MPH (97 km/h) (where legally
allowed) can improve fuel efficiency due
to reduced aerodynamic drag.
•Maintaining a safe following distance be-
hind other vehicles reduces unnecessary
braking.
•Safely monitoring traffic to anticipate
changes in speed permits reduced brak-
ing and smooth acceleration changes.
•Select a gear range suitable to road con-
ditions.
5. Use Cruise Control
•Using cruise control during highway driv-
ing helps maintain a steady speed.
•Cruise control is particularly effective in
providing fuel savings when driving on
flat terrains.
Utilize a map or navigation system to determine
the best route to save time.
FUEL EFFICIENT DRIVING TIPS
5-82Starting and driving

1. Park the vehicle on a level surface and applythe parking brake.
2. Start the engine and let it idle until it reaches the normal operating temperature,
then turn it off.
3. Remove the oil filler cap by turning it coun- terclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by turning it counterclockwise and completely
drain the oil. If the oil filter is to be changed,
remove and replace it at this time. For
additional information, refer to Changing
engine oil filter later in this section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with
a wrench. Do not use excessive force.Drain
plug tightening torque: 22 ft-lb, 30 N•m
8. Refill engine with recommended oil through the oil filler opening, then install the oil filler
cap securely.
For additional information on drain and refill
capacity, refer to Recommended fluids/
lubricants and capacities in the
9. Maintenance and Schedules section.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
amount of oil is in the engine.
9. Start the engine. Check for leakage around the drain plug and oil filter. Correct as
required.
10. Turn the engine off and wait more than 10 minutes. Check the oil level with the dip-
stick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and applythe parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise. Then
remove the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
NDI1622NDI16102.0L gasoline engine
8-6Do-it-yourself

some tire damage may not be obvious. Re-
place the tires as necessary to prevent tire
failure and possible personal injury.
•Improper service of the spare tire may result
in serious personal injury. If it is necessary
to repair the spare tire, it is recommended
that you visit an INFINITI retailer for this
service.
•For additional information regarding tires,
refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada)
in the Warranty Information Booklet.
Tires should be periodically inspected for wear,
cracking, bulging or objects caught in the tread.
If excessive wear, cracks, bulging or deep cuts
are found, the tire should be replaced immedi-
ately.
The original tires have a built-in tread wear
indicator. When the wear indicator is visible,
the tire should be replaced.
Improper servicing of a tire may result in seri-
ous personal injury. If it is necessary to repair a
tire, it is recommended you contact an INFINITI
retailer.
TIRE ROTATION
INFINITI recommends rotating the tires every
5,000 miles (8,000 km).
For additional information on tire replacing
procedures, refer to Flat tirein the6. In case
of emergency section.As soon as possible,
tighten the wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque: 96 ft-lb (130 N·m)
The wheel nuts must be kept tightened to speci-
fications at all times. It is recommended that
wheel nuts be tightened to specification at each
tire rotation interval.
WARNING
•After rotating the tires, check and adjust the
tire pressure.
•Do not include the spare tire in the tire rota-
tion.
•For additional information regarding tires,
refer to Important Tire Safety Information
(US) or Tire Safety Information in the War-
ranty Information Booklet.
REPLACING WHEELS AND TIRES
WARNING
Do not install a deformed wheel or tire even if it
has been repaired. Such wheels or tires could
have structural damage and could fail without
warning.
When replacing a tire, use the same size, speed
rating and load carrying capacity as originally
equipped. (See Wheels and Tires in the
9. Maintenance and Schedules section for
recommended types and sizes of tires and
wheels.)
If the wheels are changed for any reason,
always replace with wheels which have the
same offset dimension. Wheels of a different
offset could cause early tire wear, possibly
degraded vehicle handling characteristics
and/or interference with the brake discs/
drums. Such interference can lead to decreased
braking efficiency and/or early brake pad/shoe
wear.
8-32Do-it-yourself

Parking brake*:
Check the parking brake operation regularly.
Also make sure that the vehicle is held securely
on a fairly steep hill when only the parking
brake is applied. If the parking brake needs
adjustment, it is recommended you visit an
INFINITI retailer for this service.
Seats
:
Check seat position controls such as seat ad-
justers, seatback recliner, etc. to ensure they
operate smoothly and that all latches lock
securely in every position. Check that the head
restraints move up and down smoothly and that
the locks (if so equipped) hold securely in all
latched positions.
Seat belts
:
Check that all parts of the seat belt system (for
example, buckles, anchors, adjusters and re-
tractors) operate properly and smoothly, and
are installed securely. Check the belt webbing
for cuts, fraying, wear or damage.
Steering wheel
:
Check for changes in the steering condition,
such as excessive free play, hard steering or
strange noises.Warning lights and chimes
:
Make sure that all warning lights and chimes
are operating properly.
Windshield defroster
:
Check that the air comes out of the defroster
outlets properly and in good quantity when
operating the heater or air conditioner.
Windshield wiper and washer*
:
Check that the wipers and washer operate
properly and that the wipers do not streak.
Under the hood and vehicle
The maintenance items listed here should be
checked periodically (for example, each time
you check the engine oil or refuel).
Battery*
:
Except for maintenance free battery, check the
fluid level in each cell. It should be between the
“UPPER” and “LOWER” lines. Vehicles operated
in high temperatures or under severe condi-
tions require frequent checks of the battery
fluid level.
NOTE
Care should be taken to avoid situations that can
lead to potential battery discharge and potential
no-start conditions such as:
1. Installation or extended use of electronic ac-
cessories that consume battery power when
the engine is not running (Phone chargers,
GPS, DVD players, etc.)
2. Vehicle is not driven regularly and/or only driven short distances.
In these cases, the battery may need to be
charged to maintain battery health.
Brake fluid level*
:
Make sure that the brake fluid level is between
the “MAX” and “MIN” lines on the reservoir.
Coolant level*
:
Check the coolant level when the engine is cold.
Engine drive belt(s)*
:
Make sure that no belt is frayed, worn, cracked
or oily.
Engine oil level*
:
Check the level after parking the vehicle on a
level spot and turning off the engine. Wait more
than 15 minutes for the oil to drain back into the
oil pan.
9-4Maintenance and Schedules

Steering gear and linkage, axle and suspension
parts, drive shaft boots:
Check for damage, looseness, and leakage of
oil or grease. Under severe driving conditions,
inspect more frequently
Tire rotation:
Tires should be rotated every 6,000 miles
(10,000 km) for 2WD, every 3000 miles (5000
km) for 4WD/AWD according to the instructions
underTire rotation* earlier in this section“Ge-
neral maintenance” in this section. When rotat-
ing tires, check for damage and uneven wear.
Replace if necessary.
Transmission fluid/oil, differential oil, transfer
case oil:
Visually inspect for signs of leakage at specified
intervals. To ensure smooth, trouble-free, safe and eco-
nomical driving, INFINITI provides two mainte-
nance schedules that may be used, depending
upon the conditions in which you usually drive.
These schedules contain both distance and
time intervals, up to 120,000 miles (192,000
km)/144 months. For most people, the odom-
eter reading will indicate when service is
needed. However, if you drive very little, your
vehicle should be serviced at the regular time
intervals shown in the schedule.
After 120,000 miles (192,000 km)/144 months,
continue maintenance at the same mileage/time
intervals.
ADDITIONAL MAINTENANCE ITEMS
FOR SEVERE OPERATING SYSTEMS
Additional maintenance items for severe oper-
ating conditions; should be performed on ve-
hicles that are driven under especially demand-
ing conditions. Additional maintenance items
should be performed if you primarily operate
your vehicle under the following conditions:
•Repeated short trips of less than 5 miles in
normal temperatures or less than 10 miles in
freezing temperatures.
•Stop-and-go traffic in hot weather or low
speed driving for long distances.
•Driving in dusty conditions or on rough,
muddy or salt-spread roads.
•Towing a trailer, or using a camper or car-top
carrier.
OIL CHANGE MONITOR
This vehicle is equipped with oil change moni-
tor. It calculates engine oil and filter change
interval base on driving conditions. Driving in
severe conditions will shorten the engine oil
and filter change interval. When the Engine Oil
– Service Due Now warning appears in the
vehicle information display, the engine oil and
filter need to be replaced.
NOTE
For vehicles operated in Canada, both standard
and severe maintenance items should be per-
formed at every interval.
MAINTENANCE SERVICE MESSAGES
The maintenance service interval display in-
forms you of the next service due date.
NOTE
The maintenance service interval display does
not show any information on the engine oil level.
MAINTENANCE SCHEDULES
Maintenance and Schedules9-7

The vehicle information display shows a service
message for a few seconds, e g:
•[Service A In .. days]
•[Service A Due]
•[Service A Exceeded by .. days]
Depending on the operating conditions of the
vehicle, the remaining time or distance until the
next service due date is displayed.
The letter indicates which service is due. A
stands for a minor service and B for a major
service. A number or another letter may be
displayed after the letter.
Only for certain countries: the position after the
letter A or B indicates any necessary additional
maintenance work. If you notify an INFINITI
retailer of this display, you will receive a state-
ment on the associated costs.
The maintenance service interval display does
not take into account any periods of time during
which the battery is disconnected.
Maintaining the time-dependent service sched-
ule:
Note down the service due date displayed in the
vehicle information display before disconnect-
ing the battery.
or After reconnecting the battery, subtract the
battery disconnection periods from the service
date shown on the display.
Hiding service messages
Press the orbutton on the steering
wheel.
Displaying service messages
1. Switch the ignition on.
2. Press the
orbutton on the
steering wheel to select the [Serv.] menu.
3. Press the
orbutton to select
[Maintenance] submenu and confirm by
pressing the OK button.
The service due date appears in the vehicle
information display.
Information about service
Resetting the maintenance service interval display:
CAUTION
If the maintenance service interval display has
been inadvertently reset, this setting can be
corrected at an INFINITI retailer.
Have service work carried out as described in
the Maintenance Schedule. This may other-
wise lead to increased wear and damage to the
major assemblies or the vehicle. An INFINITI retailer will reset the maintenance
service interval display after the service work
has been carried out. You can also obtain
further information on maintenance work, for
example.
Special service requirements
:
The prescribed service interval is based on
normal operation of the vehicle. Service work
will need to be performed more often if the
vehicle is operated under arduous conditions or
increased loads, for example:
•Regular city driving with frequent intermedi-
ate stops
•If the vehicle is primarily used to travel short
distance
•For frequent operation in mountainous ter-
rain or on poor road surfaces
•If the engine is often left idling for long
periods
In these or similar operating conditions, have,
for example, the air filter, engine oil and oil
filter changed more frequently. The tires must
be checked more frequently if the vehicle is
operated under increased loads. Further infor-
mation can be obtained at an INFINITI retailer.
9-8Maintenance and Schedules

•The fuel should be unleaded and have an oc-
tane rating no lower than that recommended
for unleaded gasoline.
•If an oxygenate-blend, other than a methanol
blend, is used, it should contain no more than
10% oxygenate. (MTBE may, however, be
added up to 15%.)
•E-15 fuel contains more than 10% oxygenate.
E-15 fuel will adversely affect the emission
control devices and systems of the vehicle
and should not be used. Damage caused by
such fuel is not covered by the INFINITI New
Vehicle Limited Warranty.
•If a methanol blend is used, it should contain
no more than 5% methanol (methyl alcohol,
wood alcohol). It should also contain a suit-
able amount of appropriate cosolvents and
corrosion inhibitors. If not properly formu-
lated with appropriate cosolvents and corro-
sion inhibitors, such methanol blends may
cause fuel system damage and/or vehicle
performance problems.
At this time, sufficient data is not available to
ensure that all methanol blends are suitable
for use in INFINITI vehicles.
If any driveability problems such as engine
stalling and difficult hot-starting are experi-
enced after using oxygenate-blend fuels, imme- diately change to a nonoxygenate fuel or a fuel
with a low blend of MTBE.
Take care not to spill gasoline during refueling.
Gasoline containing oxygenates can cause paint
damage.
E-15 fuel
E-15 fuel is a mixture of approximately 15% fuel
ethanol and 85% unleaded gasoline. E-15 can
only be used in vehicles designed to run on E-15
fuel. Do not use E-15 in your vehicle. U.S.
government regulations require fuel ethanol
dispensing pumps to be identified with small,
square, orange and black label with the com-
mon abbreviation or the appropriate percentage
for that region.
E-85 fuel
E-85 fuel is a mixture of approximately 85% fuel
ethanol and 15% unleaded gasoline. E-85 can
only be used in a Flexible Fuel Vehicle (FFV). Do
not use E-85 fuel in your vehicle. U.S. govern-
ment regulations require fuel ethanol dispens-
ing pumps to be identified by a small, square,
orange and black label with the common abbre-
viation or the appropriate percentage for that
region.
Fuel containing MMT
MMT, or methylcyclopentadienyl manganese tri-
carbonyl, is an octane boosting additive.
INFINITI does not recommend the use of fuel
containing MMT. Such fuel may adversely affect
vehicle performance, including the emissions
control system. Note that while some fuel
pumps label MMT content, not all do, so you
may have to consult your gasoline retailer for
more details.
Aftermarket fuel additives
INFINITI does not recommend the use of any
aftermarket fuel additives (Example: fuel injec-
tor cleaner, octane booster, intake valve de-
posit removers, etc.) which are sold commer-
cially. Many of these additives intended for
gum, varnish or deposit removal may contain
active solvent or similar ingredients that can be
harmful to the fuel system and engine.
Octane rating tips
Using unleaded gasoline with an octane rating
lower than recommended above can cause per-
sistent, heavy spark knock. (Spark knock is a
metallic rapping noise.) If severe, this can lead
to engine damage. If you detect a persistent
heavy spark knock even when using gasoline of
the stated octane rating, or if you hear steady
spark knock while holding a steady speed on
10-4Technical information

level roads, it is recommended you have an
INFINITI retailer correct the condition. Failure to
correct the condition is misuse of the vehicle, for
which INFINITI is not responsible.
Incorrect ignition timing will result in knocking,
after-run and/or overheating. This in turn may
cause excessive fuel consumption or damage to
the engine. If any of the above symptoms are
encountered, have your vehicle checked. It is
recommended you visit an INFINITI retailer.
However, now and then you may notice light
spark knock for a short time while accelerating
or driving up hills. This is no cause for concern,
because you get the greatest fuel benefit when
there is light spark knock for a short time under
heavy engine load.
1API certification mark
2API service symbol
ENGINE OIL AND OIL FILTER
RECOMMENDATIONS
Selecting the correct oil
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure sat-
isfactory engine life and performance. For addi-
tional information, refer toRecommended
fluids/lubricants and capacities earlier in this
section. INFINITI recommends the use of an
energy conserving oil in order to improve fuel
economy.
Select only engine oils that meet the American
Petroleum Institute (API) certification or Interna-
tional Lubricant Standardization and Approval Committee (ILSAC) certification and SAE viscos-
ity standard. These oils have the API certifica-
tion mark on the front of the container. Oils
which do not have the specified quality label
should not be used as they could cause engine
damage.
Oil additives
INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used and
maintenance intervals are followed.
Oil which may contain foreign matter or has
been previously used should not be used.
Oil viscosity
The engine oil viscosity or thickness changes
with temperature. Because of this, it is impor-
tant that the engine oil viscosity be selected
based on the temperatures at which the vehicle
will be operated before the next oil change.
Choosing an oil viscosity other than that recom-
mended could cause serious engine damage.
Selecting the correct oil filter
Your new vehicle is equipped with a high—
quality genuine INFINITI oil filter. When replac-
ing, it is recommended you use the genuine oil
filter or its equivalent for the reason described
in “Change intervals”.
NTI326
Technical information10-5

knee air bag will deflate quickly after the collision
is over OR the knee air bag will remain inflated for
a short time.
The knee air bags operate only when the
ignition switch is placed in the ON position.
After placing the ignition switch in the ON
position, the supplemental air bag warning
light illuminates. The supplemental air bag
warning light will turn off a few seconds
after the engine starts if the system is op-
erational.
WARNING
●Do not place any objects between the
knee bolster and the driver’s seat. Such
objects may become dangerous projec-
tiles and cause injury if a knee air bag
inflates.
● Right after inflation, the knee air bag
system components will be hot. Do not
touch them; you may severely burn
yourself.
● No unauthorized changes should be
made to any components or wiring of
the knee air bag system. This is to pre-
vent damage to or accidental inflation
of the knee air bag system. ●
Do not make unauthorized changes to
your vehicle’s electrical system or sus-
pension system. This could affect
proper operation of the knee air bag
system.
● Tampering with the knee air bag system
may result in serious personal injury.
For example, do not change the driver
knee bolster or install additional trim
material around the knee air bag.
● It is recommended that you visit an
INFINITI retailer for work on and around
the knee air bag. It is also recom-
mended that you visit an INFINITI re-
tailer for installation of electrical equip-
ment. The SRS wiring harnesses*
should not be modified or discon-
nected. Unauthorized electrical test
equipment and probing devices should
not be used on the knee air bag system.
*The SRS wiring harness or connectors
are yellow or orange for easy
identification.
When selling your vehicle, we request that you
inform the buyer about the knee air bag system
and guide the buyer to the appropriate sections
in this manual.
Seat belt with pretensioner(s)
WARNING
● The pretensioner(s) cannot be reused
after activation. They must be replaced
together with the retractor and buckle
as a unit.
● If the vehicle becomes involved in a
collision but pretensioner(s) are not ac-
tivated, be sure to have the preten-
sioner system checked and, if neces-
sary, replaced. It is recommended that
you visit an INFINITI retailer for this
service.
● No unauthorized changes should be
made to any components or wiring of
the pretensioner system. This is to pre-
vent damage to or accidental activation
of the pretensioner(s) . Tampering with
the pretensioner system may result in
serious personal injury.