change time INFINITI QX30 2017 User Guide

AUDIO OPERATION PRECAUTIONS
WARNING
•The driver must not attempt to operate the
audio system while the vehicle is in motion,
so that full attention may be given to vehicle
operation.
•Park the vehicle in a safe location and apply
the parking brake before operating the au-
dio system and playing movies (if
equipped).
CAUTION
•Operate the audio system only when the
vehicle engine is running. Operating the au-
dio system for extended periods of time
with the engine turned off can discharge the
vehicle battery.
•Do not allow the system to get wet. Exces-
sive moisture such as spilled liquids may
cause the system to malfunction.
Radio
Turn the ignition switch to the ACC or ON
position before turning on the radio. If you
listen to the radio when the engine is not
running, the ignition switch should be pushed
to the ACC position.
Radio reception is affected by station signal
strength, distance from radio transmitter, build-
ings, bridges, mountains and other external
influences. Intermittent changes in reception
quality are normally caused by these external
influences.
Using a cellular phone in or near the vehicle may
influence radio reception quality.
Radio reception
Your radio system is equipped with state-of-the-
art electronic circuits to enhance radio recep-
tion. These circuits are designed to extend
reception range, and to enhance the quality of
that reception.
However there are some general characteristics
of both FM and AM radio signals that can affect
radio reception quality in a moving vehicle,
even when the best quality equipment is used.
These characteristics are completely normal in
a given reception area, and do not indicate any
malfunction in your radio system.Reception conditions will constantly change
because of vehicle movement. Buildings, ter-
rain, signal distance and interference from
other vehicles can adversely affect ideal recep-
tion. Described below are some of the factors
that can affect radio reception.
Some cellular phones or other devices may
cause interference or a buzzing noise to come
from the audio system speakers. Storing the
device in a different location may reduce or
eliminate the noise.
AUDIO SYSTEM (IF EQUIPPED)
4-52Display screen, heater and air conditioner, and audio system

2[Source]: Touch to switch to the source
select screen. SeeSelecting audio
source later in this section
3[Control]: Touch to display the control
screen. See Radio Controls later in this
section
4HD Radio reception status indicator (for
AM and FM):
The icon is displayed when HD Radio digital
signal is received. The icon flashes when
the radio is acquiring the digital signal but
the sound output is not yet in the HD mode.
5Radio band indicator: The currently se-
lected radio band (AM, FM or SXM) is dis-
played.
6Reception information display: Reception
information available at the time such as
frequency, station/channel name, etc.. are
displayed.
On the SXM screen, touch this area to
display the category list.
736 stations/channels can be registered in
the preset list.
See Presetting later in this section. NOTE
HD Radio reception needs to be activated to re-
ceive HD Radio broadcasts. This enables you to
receive radio broadcasts digitally (where avail-
able), providing a better quality sound with clear
reception. When this feature is not activated or
HD Radio broadcasts are not available, you will
receive analog radio (AM/FM broadcasts).
Radio source control
There are 2 elements used in the preset list area
that are associated with radio source:
1Highlight for INFINITI controller operation.
2(With triangle) Indicator of current se-
lected preset station.
Radio operation
Radio activation and band selection:
Push
or select the preferred radio band
(AM, FM or SXM) from the audio source list to
turn on the radio. Each time is pushed,
the radio band will change.
For details, see Selecting audio source later in
this section.
NAA1717
Display screen, heater and air conditioner, and audio system4-67

NOTE
When the stereo broadcast signal is weak, the
radio will automatically change from stereo to
monaural reception.
Seeking stations/channels
:
AM and FM Radio
Push to tune from low to
high or high to low frequencies and to stop at
the next broadcasting station.
SiriusXM Satellite Radio
Push to tune to the first
channel of the next or previous category.
Scan tuning
:
To tune the stations/channels, touch [Control]
on the display and touch [Scan]. The stations/
channels will be tuned form low to high fre-
quencies and stop at each broadcasting
station/channel for 5 seconds. Touching [Scan]
again during this 5 second period will stop scan
tuning and the radio will remain tuned to that
station/channel.
Presetting
:
Up to 36 stations/channels can be registered
for AM, FM and SXM in the preset list.
1. Select a radio band (AM, FM or SXM). 2. Tune to the station/channel you wish to
store in the preset list.
3. (Radio screen operation) Touch and hold one of the preset numbers in the preset list.
(Radio memory buttons operation) Push and
hold the desired station/channel preset but-
ton <1> to <6>.
4. The information such as frequency (AM/FM), channel number (SXM), etc. will be dis-
played on the preset list.
To change the preset stations/channels, touch
and hold one of the preset numbers. You can
select whether to change the station/channel or
to delete the preset setting.
Alert notification (SXM only)
:
Favorite artists and songs can be registered to
receive an alert notice wen a song of the
registered conditions is on the radio. To tune to
the respective channel, touch [Listen to be
consistent]. The alert can be ignored by touch-
ing [Cancel].
Satellite Radio:
•The satellite mode requires and active
SiriusXM Satellite Radio subscription. The
satellite service is available only to those at
least 18 and older in the 48 contiguous
United States.
•It may take some time to receive the activa-
tion signal after the initiation of the SiriusXM
Satellite Radio subscription. After receiving
the activation signal, an available channel
list will automatially be updated in the radio.
Switch the ignition switch from LOCK to ACC
to update the SiriusXM channel list.
Radio Controls
Touch [Control] on the AM, FM or SXM screen to
display the control screen.
The following items are available:
FM/AM
:
•[Station List]
Touch to display the available station list.
While listening to FM radio, Auto Update is
not performed.
•[Scan]
Touch to scan tune the stations
See Radio operation earlier in this section
•[HD mode]
When this item is turned on, the analog and
digital reception switches automatically.
When this item is turned off, te reception is
fixed in the analog mode.
4-68Display screen, heater and air conditioner, and audio system

COMPACT DISC (CD) PLAYER
How to view CD operation screen1[Source]:
Touch to switch to the source list screen.
For details, seeSelecting audio source
later in this section
2[Scan]:
Touch to play the first 10 seconds of the
tracks. Touch again to stop scanning.
3Track information:
Track information such as the song title,
artist name, and album name is dis-
played.
4Audio source indicator:
Indicates that CD is currently selected.
5Play time:
The play time of the track is displayed.
6Track number:
This indicates the current track number
and the total number of tracks.
7CD menu:
CD menu items are displayed. Touch an
icon to display the list or to change the
setting.
- [Track]
- [Folder] (for MP3, WMA, AAC)
- [Play Mode]
8Play Mode Indicator:
This indicates the current play mode.
Touch to change the play mode.
9Folder number (for MP3, WMA, AAC):
This indicates the folder number when a
CD with compressed audio files is loaded.NAA1718
4-70Display screen, heater and air conditioner, and audio system

4Track information:
Track information such as the song title,
artist name and album name is displayed.
5Audio source indicator:
This indicates that iPod is currently se-
lected among other sources.
6Album artwork (if equipped):
An image of the album artwork is displayed
when available.
7Track number:
This indicates the track number and the
total number of tracks.
8Shuffle mode indicator:
Touch to change the shuffle mode.
Mode Screen display
Shuffle albums
Albums
All Songs
Songs
Shuffle Off
OFF
9[]/[]:
Touch to play/pause the track.
10iPod menu:
- [Previous List]
- [Playlists]
- [Artists]
- [Songs]
- [Albums]
- [Genres]
- [Composers] - [Podcasts]
- [Audiobooks]
- [Shuffle]
- [Repeat]
11Repeat mode indicator:
Touch to change the repeat mode.
Mode Screen display
All Track Repeat
All
1 Track Repeat
1 Track
Repeat Off
OFF
iPod player operation
Activation and playing:
Inserting the iPod cable into the connector will
activate the iPod mode.
iPod can also be selected from the audio
sources list and the source bar by touch panel
operation or by pushing .
Selecting audio source page 4-65
Main audio buttons page 4-63
To play and pause the iPod, touch [Play]/
[Pause] in the iPod menu. Selecting search method
:
A list of search methods is displayed in the iPod
menu. Touch and select an item to play the iPod
in your preferred settings.
Fast-forwarding/rewinding
:
Push and hold
to fast-
forward or rewind the song. Release CAT•TRACK> to play the song at normal speed.
Changing play mode
:
Touch [Shuffle] or [Repeat] from the iPod menu
to select the play mode.
Skipping songs
:
Push to skip to the next or
previous song.
Even when iPods or iPhones are inserted into
both of the two USB connectors, the system
recognizes only one of the connected iPods or
iPhones at a time.
BLUETOOTH® STREAMING AUDIO
Your vehicle is equipped with Bluetooth®
Streaming Audio.
If you have a compatible Bluetooth® device
with streaming audio (A2DP profile), you can set
up a wireless connection between your
Bluetooth® device and the in-vehicle audio
4-76Display screen, heater and air conditioner, and audio system

system. This connection allows you to listen to
the audio from the Bluetooth® device using
your vehicle speakers. It may also allow basic
control of the device for playing and skipping
audio files using the AVRCP Bluetooth® profile.
Not all Bluetooth® devices have the same level
of controls for AVRCP. Please consult the
manual for your Bluetooth® device for more
details.
Wireless LAN (Wi-Fi) and the Bluetooth® func-
tions share the same frequency band (2.4 GHz).
Using the Bluetooth® and the wireless LAN
functions at the same time may slow down or
disconnect the communication and cause unde-
sired noise. It is recommended that you turn off
the wireless LAN (Wi-Fi) when using the
Bluetooth® functions.
Regulatory Information
FCC Regulatory information:
FCC ID : HYQDNNS075
NOTE: This device complies with part 15 of the
FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including in-
terference that may cause undesired operation.FCC WARNING: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
CAUTION : Radio Frequency Radiation Exposure
This equipment complies with FCC radiation
exposure limits set forth for uncontrolled envi-
ronment and meets the FCC radio frequency (RF)
Exposure Guidelines. This equipment has very
low levels of RF energy that it deemed to comply
without maximum permissive exposure evalua-
tion (MPE). But it is desirable that it should be
installed and operated with at least 20cm and
more between the radiator and person’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
IC Regulatory information
:
The antenna cannot be removed (and changed)
by user.
NOTE: This device complies Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.CAUTION : Radio Frequency Radiation Exposure
This equipment complies with IC radiation ex-
posure limits set forth for uncontrolled environ-
ment and meets RSS-102 of the IC radio fre-
quency (RF) exposure rules. This equipment has
very low levels of RF energy that it deemed to
comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it
should be installed and operated with at least
20cm and more between the radiator and per-
son’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
This Class B digital apparatus meets all require-
ments of the Canadian Interference Causing
Equipment Regulations.
Connecting Bluetooth® streaming
audio device
Bluetooth® streaming audio device must be
connected to the vehicle before operation.
Connecting Bluetooth® device page 4-88
Display screen, heater and air conditioner, and audio system4-77

How to view Bluetooth® streaming
audio operation screen
1[Source]:
Touch to switch to the source list screen.
Selecting audio source page 4-65
2Track information:
Track information such as the song title,
artist name and folder name is displayed.
3Audio source indicator:This indicates that Bluetooth® streaming audio
is currently selected among other sources.
4Play time:
The play time of the track is displayed.
5[Control]:
Touch to display the control screen.
Bluetooth® streaming audio operation
page 4-79
6Track number
This indicates the track number.
7Repeat mode indicator:
Touch to change the repeat mode.
Mode Screen display
All repeat
All
1 Folder Repeat
1 Folder
1 Track Repeat
1 Track
Repeat Off
OFF
8Bluetooth® streaming audio menu:
- [Play]
- [Pause]
- [Folder/Track]
- [Repeat]
- [Random]
NAA1634
4-78Display screen, heater and air conditioner, and audio system

9Random mode indicator:
Touch to change the random mode.
ModeScreen display
All Random
All
1 Folder Random
1 Folder
Random Off
OFF
Depending on the audio device that is con-
nected to the vehicle, track information may not
be displayed.
Bluetooth® streaming audio
operation
The ability to pause, change tracks, fast-
forward, rewind, randomize and repeat music
may be different between devices. Some or all
of these functions may not be supported on
each device.
•Depending on the Bluetooth® streaming au-
dio device that is connected, it may not be
possible to perform audio operations.
•Depending on the Bluetooth® streaming au-
dio device that is connected, a time lag may
occur before music is played back.
•Depending on the application except for the
native audio application that is played on the
Bluetooth® streaming audio device, incor-
rect behavior (information lacking, timer
skipping, etc.) may occur.
Activation and playing
:
Bluetooth® streaming audio device can be se-
lected from audio sources list by touching
[Source] or by pushing .
Selecting audio source page 4-65
Main audio buttons page 4-63
To play the Bluetooth® streaming audio device,
touch [Play], and to pause the Bluetooth®
streaming audio device touch [Pause] in the
Bluetooth® streaming audio menu.
Selecting folder/track
:
Touch [Folder/Track] to select a folder/track.
Changing play mode
:
Touch [Repeat] or [Random] in the Bluetooth®
streaming audio menu to change the play
mode.
Fast-forwarding/rewinding
:
Push and hold to fast-
forward or rewind the song. Release CAT•TRACK> to play the song at normal speed. Skipping songs/folders
:
Push to skip to the next or
previous song.
To skip to the next or previous folder, Push
.
Bluetooth® streaming audio controls
Touch [Control] on the Bluetooth® Audio opera-
tion screen to display the control screen.
[Select
Audio
Device]
Touch to select a different
Bluetooth® streaming audio device
from a list of registered Bluetooth®
devices.
See
Bluetooth® settings later in
this section
[Connect
Device] Touch to connect a new Bluetooth®
device.
Display screen, heater and air conditioner, and audio system4-79

•Some Bluetooth® enabled cellular phones
may not be recognized by the in-vehicle
phone module. Please visit
www.infinitiusa.com/bluetooth and search
for a recommended phone list.
•You will not be able to use a hands-free
phone under the following conditions:– Your vehicle is outside the service area for your cellular phone network.
– Your vehicle is in an area where it is difficult to receive radio waves, such as in
a tunnel, in an underground parking ga-
rage, behind a tall building or in a moun-
tainous area.
– Your cellular phone is locked in order to prevent dialing.
•When the radio wave condition is not ideal or
ambient sound is too loud, it may be difficult
to hear the other person’s voice during a call.
•This Bluetooth® system supports Wideband
speech, which enhances the sound quality of
phone calls placed over Bluetooth®. To take
advantage of this feature, the cellular device
should be used on a carrier supporting Adap-
tive Multi-Rate Wideband (AMR-WB) or HD
voice technology. The performance of
AMR-WB may vary by carrier and calling area.
Consult your cellular carrier if you experience
issues with call quality or connection.
•Immediately after the ignition switch is
turned ON, it may be impossible to receive a
call for a short period of time.
•Do not place the cellular phone in an area
surrounded by metal or far away from the
in-vehicle phone module to prevent tone
quality degradation and wireless connection
disruption.
•While a cellular phone is connected through
the Bluetooth® wireless connection, the bat-
tery of the cellular phone may discharge
quicker than usual.
•If the Bluetooth® Hands-Free Phone System
seems to be malfunctioning, please visit
www.infinitiusa.com/bluetooth for trouble-
shooting help.
•Some cellular phones or other devices may
cause interference or a buzzing noise to be
emitted from the audio system speakers.
Storing the device in a different location may
reduce or eliminate the noise.
•Refer to the owner’s manual for the cellular
phone for information regarding the tele-
phone pairing procedure specific to your
phone, battery charging, and cellular phone
antenna, etc.
•The antenna display on the monitor may not
match the antenna display of some cellular
phones.
•The battery display on the monitor may not
match the battery display of some cellular
phones.
•Keep the interior of the vehicle as quiet as
possible to hear the caller’s voice clearly as
well as to minimize echoes.
•If reception between callers is unclear, ad-
justing the incoming or outgoing call volume
may improve the clarity.
REGULATORY INFORMATION
FCC Regulatory Information
FCC ID : HYQDNNS075
NOTE: This device complies with part 15 of the
FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including in-
terference that may cause undesired operation.
FCC WARNING: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
4-84Display screen, heater and air conditioner, and audio system

•[Select Audio Device]
Registered Bluetooth® audio players are
shown on the list. Select a device from the
list to disconnect or connect a Bluetooth®
device.
•[Vehicle Bluetooth Device Info.]
The registered device name and the PIN code
can be changed.
HANDS-FREE TEXT MESSAGING
ASSISTANT
WARNING
•Use the text messaging feature after park-
ing your vehicle in a safe location. If you
have to use the feature while driving, exer-
cise extreme caution at all times so full at-
tention may be given to vehicle operation.
CAUTION
•This feature is disabled if the connected de-
vice does not support the Message Access
Profile (MAP). Refer to the owner’s manual
for your phone for further details and
instructions.Laws in some jurisdictions may restrict the use
of
Text-to-Speech. Check local regulations be-
fore using this feature.
The text messaging assistant system allows the
sending and receiving of the text messages
through the vehicle interface.
Receiving a message
When the cellular phone connected to the ve-
hicle receives a text message, a notification is
displayed on the display accompanied by a
tone.
To check the message, touch [Check Now].
Touch [Later] to save the message to be
checked later.
Using the text message function with
iPhone
R. If you would like to use the text
message function with your iPhone, please
make the below steps.
1) Connect iPhone
Rto the Bluetooth®
Hands-Free Phone System.
2) Disconnect iPhone
Rfrom vehicle setting
menu.
5GF0038XZ
Display screen, heater and air conditioner, and audio system4-89