start and stop INFINITI QX30 2017 Manual PDF

6.Avoid Idling
•Shutting off your engine when safe for
stops exceeding 30 seconds saves fuel
and reduces emissions.
7. Buy an Automated Pass for Toll Roads
•Automated passes permit drivers to use
special lanes to maintain cruising speed
through the toll and avoid stopping and
starting.
8. Winter Warm Up
•Limit idling time to minimize impact to
fuel economy.
•Vehicles typically need no more than 30
seconds of idling at start-up to effectively
circulate the engine oil before driving.
•Your vehicle will reach its ideal operating
temperature more quickly while driving
versus idling.
9. Keeping your Vehicle Cool
•Park your vehicle in a covered parking
area or in the shade whenever possible.
•When entering a hot vehicle, opening the
windows will help to reduce the inside
temperature faster, resulting in reduced
demand on your A/C system.
•Keep your engine tuned up.
•Follow the recommended scheduled mainte-
nance.
•Keep the tires inflated to the correct pres-
sure. Low tire pressure increases tire wear
and lowers fuel economy.
•Keep all the wheels in correct alignment.
Improper alignment increases tire wear and
lowers fuel economy.
•Use the recommended viscosity engine oil.
For additional information, see Recom-
mended fluids/lubricants and capacities in
the 10. Technical information section
WARNING
•Do not drive beyond the performance capa-
bility of the tires, even with 4WD engaged.
Accelerating quickly, sharp steering ma-
neuvers or sudden braking may cause loss
of control.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
•This vehicle is not designed for off-road
(rough road) use. Do not drive on sandy or
muddy roads that tires may get stuck in.
•For 4WD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any drive or reverse po-
sition with the engine running. Doing so
may result in drivetrain damage or unex-
pected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
•Do not attempt to test a 4WD equipped ve-
hicle on a 2-wheel dynamometer (such as
the dynamometers used by some states for
emissions testing) or similar equipment
even if the other two wheels are raised off
the ground. Make sure that you inform the
test facility personnel that your vehicle is
INCREASING FUEL ECONOMY FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED)
Starting and driving5-83

equipped with 4WD before it is placed on a
dynamometer. Using the wrong test equip-
ment may result in drivetrain damage or un-
expected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
•When a wheel is off the ground due to an
uneven surface, do not spin the wheel
excessively.
CAUTION
Never tow the vehicle with one axle raised. This
may damage the differential. Damage of this
sort is not covered by the warranty. All wheels
must be fully raised (seeFour-Wheel Drive
(4WD) models in the6. In case of emergency
section)
4WD, together with VDC, improves the traction
of your vehicle whenever a drive wheel spins
due to insufficient grip.
If you fail to adapt your driving style, 4WD can
neither reduce the risk of an accident nor
override the laws of physics. 4WD cannot take
account of road, weather, and traffic conditions.
4WD is only an aid. You are responsible for the
distance to the vehicle in front, for vehicle speed, for braking in good time, and for staying
in lane.
If a drive wheel spins due to insufficient grip
•When pulling away, only depress the accel-
erator pedal as far as is necessary.
•Accelerate less when driving.
NOTE
In wintry driving conditions, the maximum effec-
tiveness of 4WD can only be achieved if you use
winter tires (M+S tires), with snow chains if nec-
essary.
WARNING
•Do not stop or park the vehicle over flam-
mable materials such as dry grass, waste
paper or rags. They may ignite and cause a
fire.
•Safe parking procedures require that both
the parking brake be applied and the P
(Park) position engaged. Failure to do so
could cause the vehicle to move unexpect-
edly or roll away and result in an accident.
•When parking the vehicle, make sure the P
(Park) position is engaged. The shift lever
cannot be moved out of the P (Park) position
without depressing the brake pedal.
•Never leave the engine running while the
vehicle is unattended.
•To help avoid risk of injury or death through
unintended operation of the vehicle and/or
its systems, do not leave children, people
who require the assistance of others, or
pets unattended in your vehicle. Addition-
ally, the temperature inside a closed vehicle
on a warm day can quickly become high
enough to cause a significant risk of injury
or death to people and pets.
PARKING
5-84Starting and driving

CAUTION
•If wheels or tires other than INFINITI recom-
mended ones are used, the power steering
system may not operate properly and the
[Power Steering Malfunction See Operators
Manual] warning may appear in the vehicle
information display.
•Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings
and wheels are not INFINITI recommended
for your vehicle or are extremely deterio-
rated, the power steering system may not
operate properly and the [Power Steering
Malfunction See Operators Manual] warn-
ing may appear in the vehicle information
display.
•Do not modify the vehicle’s steering. If
steering parts are not INFINITI recom-
mended for your vehicle or are extremely
deteriorated, the power steering system
may not operate properly and the [Power
Steering Malfunction See Operators
Manual] warning may appear in the vehicle
information display.
•Do not place the ignition switch in the on
position while the steering wheel or a tire is
removed.
•Do not turn the steering wheel as much as
possible while the ignition switch is in any
position other than the ON position.
•Installing an accessory on the steering
wheel, or changing the steering wheel, may
reduce the steering performance.
NOTE
When the steering wheel is operated repeatedly
or continuously while parking or driving at a very
low speed, the power assistance for the steering
wheel will be reduced. This is to prevent over-
heating of the electric power steering system
and protect it from becoming damaged. While
the power assistance is reduced, steering wheel
operation will become heavy. When the tem-
perature of the electric power steering system
decreases, the power assistance level will return
to normal. Avoid repeating such steering wheel
operations that could cause the electric power
steering system to overheat. The brake system has two separate hydraulic
circuits. If one circuit malfunctions, you will still
have braking ability at two wheels.BRAKE PRECAUTIONS
WARNING
While driving on a slippery surface, be careful
when braking, accelerating or downshifting.
Abrupt braking or accelerating could cause the
wheels to skid and result in an accident.
Vacuum assisted brakes
The brake booster aids braking by using engine
vacuum. If the engine stops, you can stop the
vehicle by depressing the brake pedal. How-
ever, greater foot pressure on the brake pedal
will be required to stop the vehicle. The stop-
ping distance will be longer.
WARNING
•If the engine is not running or is turned off
while driving, the power assist for the
brakes will not work. Braking will be harder.
•Do not coast with the engine stopped.
When the brake pedal is depressed slowly and
firmly, you may hear a clicking noise and feel a
BRAKE SYSTEM
Starting and driving5-87

slight pulsation. This is normal and indicates
that the Brake Assist System is operating (if
equipped).
Using brakes
Avoid resting your foot on the brake pedal while
driving. This will overheat the brakes, wear out
the brake linings/pads faster, and increase fuel
consumption.
To help reduce brake wear and to prevent the
brakes from overheating, reduce speed and
downshift to a lower gear before going down a
slope or long grade. Overheated brakes may
reduce braking performance and could result in
loss of vehicle control.
While driving on a slippery surface, be careful
when braking, accelerating or downshifting.
Abrupt braking or acceleration could cause the
wheels to skid and result in an accident.
Wet brakes
When the vehicle is washed or driven through
water, the brakes may get wet. As a result, your
braking distance will be longer and the vehicle
may pull to one side during braking.
To dry the brakes, drive the vehicle at a safe
speed while lightly depressing the brake pedal
to heat up the brakes. Do this until the brakesreturn to normal. Avoid driving the vehicle at
high speeds until the brakes function correctly.
Driving uphill
When starting on a steep gradient, it is some-
times difficult to operate the brake. Use the
parking brake to hold the vehicle. When ready
to start, make sure that the shift lever is in an
appropriate forward or reverse driving position,
release the parking brake while depressing the
accelerator pedal. If your vehicle has an electric
parking brake, this will automatically release
when you depress the accelerator pedal (DCT
models).
Driving downhill
The engine braking action is effective for con-
trolling the vehicle while descending hills.
A low gear position in the manual shift mode,
low enough to obtain sufficient engine braking,
should be selected.
Parking brake break-in
Break in the parking brake shoes whenever the
stopping effect of the parking brake is weak-
ened or whenever the parking brake shoes
and/or drums/rotors are replaced, in order to
assure the best braking performance.
This procedure is described in the vehicle ser-
vice manual and can be performed by an
INFINITI retailer.
ANTI-LOCK BRAKING SYSTEM (ABS)
WARNING
The Anti-lock Braking System (ABS) is a so-
phisticated device, but it cannot prevent acci-
dents resulting from careless or dangerous
driving techniques. It can help maintain ve-
hicle control during braking on slippery sur-
faces. Remember that stopping distances on
slippery surfaces will be longer than on normal
surfaces even with ABS. Stopping distances
may also be longer on rough, gravel or snow
covered roads, or if you are using tire chains.
Always maintain a safe distance from the ve-
hicle in front of you. Ultimately, the driver is
responsible for safety.
Tire type and condition may also affect braking
effectiveness.
– When replacing tires, install the specified
size of tires on all four wheels.
– When installing a replacement tire, make sure
that it is the proper size and type as specified
on the tire and loading information label. (See
5-88Starting and driving

Wheels and Tiresin the9. Maintenance and
Schedules section.)
– For detailed information, see Wheels and
tires in the 8. Do-it-yourself section.
The Anti-lock Braking System (ABS) controls the
brakes so the wheels do not lock during hard
braking or when braking on slippery surfaces.
The system detects the rotation speed at each
wheel and varies the brake fluid pressure to
prevent each wheel from locking and sliding. By
preventing each wheel from locking, the system
helps the driver maintain steering control and
helps to minimize swerving and spinning on
slippery surfaces.
Using system
Depress the brake pedal and hold it down.
Depress the brake pedal with firm steady pres-
sure, but do not pump the brakes. The ABS will
operate to prevent the wheels from locking up.
Steer the vehicle to avoid obstacles.
WARNING
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer.
The computer has a built-in diagnostic feature
that tests the system each time you start the
engine and move the vehicle at a low speed in
forward or reverse. When the self-test occurs,
you may hear a “clunk” noise and/or feel a
pulsation in the brake pedal. This is normal and
does not indicate a malfunction. If the computer
senses a malfunction, it switches the ABS off
and illuminates the ABS warning light on the
instrument panel. The brake system then oper-
ates normally, but without anti-lock assistance.
If the ABS warning light illuminates during the
self-test or while driving, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
Normal operation
The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according to
road conditions.
When the ABS senses that one or more wheels
are close to locking up, the actuator rapidly
applies and releases hydraulic pressure. This
action is similar to pumping the brakes very
quickly. You may feel a pulsation in the brake
pedal and hear a noise from under the hood or
feel a vibration from the actuator when it is
operating. This is normal and indicates that the
ABS is operating properly. However, the pulsa-
tion may indicate that road conditions are haz-
ardous and extra care is required while driving.
Starting and driving5-89

WARNING
•Never rely solely on the Hill Start Assist
(HSA) system to prevent the vehicle from
moving backward on a hill. Always drive
carefully and attentively. Depress the brake
pedal when the vehicle is stopped on a
steep hill. Be especially careful when
stopped on a hill on frozen or muddy roads.
Failure to prevent the vehicle from rolling
backwards may result in a loss of control of
the vehicle and possible serious injury or
death.
•The Hill Start Assist system is not designed
to hold the vehicle at a standstill on a hill.
Depress the brake pedal when the vehicle is
stopped on a steep hill. Failure to do so may
cause the vehicle to roll backwards and may
result in a collision or serious personal in-
jury.
•The Hill Start Assist system may not prevent
the vehicle from rolling backwards on a hill
under all load or road conditions. Always be
prepared to depress the brake pedal to pre-
vent the vehicle from rolling backwards.
Failure to do so may result in a collision or
serious personal injury.
•After a short time, hill start assist will no
longer brake your vehicle and it could rollaway There is a risk of an accident and in-
jury. Therefore, quickly move your foot from
the brake pedal to the accelerator pedal.
Never leave the vehicle when it is held by
hill start assist.
Hill start assist helps you when pulling away
forwards or in reverse on an uphill gradient. It
holds the vehicle for a short time after you have
removed your foot from the brake pedal. This
gives you enough time to move your foot from
the brake pedal to the accelerator pedal and
depress it before the vehicle begins to roll.
Hill start assist is not active if
•You are pulling away on a level road or a
downhill gradient.
•On vehicles with automatic transmission, the
transmission is in position N.
•The electric parking brake is applied.
•VDC is malfunctioning.
FREEING A FROZEN DOOR LOCK
To prevent a door lock from freezing, apply
deicer through the key hole. If the lock becomes
frozen, heat the key before inserting it into the
key hole, or use the INFINITI Intelligent Key.
ANTIFREEZE
In the winter when it is anticipated that the
temperature will drop below 32°F (0°C), check
the antifreeze to assure proper winter protec-
tion. For additional information, see Engine
cooling system in the8. Do-it-yourself sec-
tion.
BATTERY
If the battery is not fully charged during ex-
tremely cold weather conditions, the battery
fluid may freeze and damage the battery. To
maintain maximum efficiency, the battery
should be checked regularly. For details, see
Battery in the8. Do-it-yourself section of this
manual.
DRAINING OF ENGINE COOLANT
If the vehicle is to be left outside without
antifreeze, drain the cooling system, including
the engine block. Refill before operating the
vehicle. For details, see Changing engine
HILL START ASSIST (HSA) COLD WEATHER DRIVING
Starting and driving5-93

coolantin the8. Do-it-yourself section of this
manual.
TIRE EQUIPMENT
1. SUMMER tires have a tread designed to provide superior performance on dry pave-
ment. However, the performance of these
tires will be substantially reduced in snowy
and icy conditions. If you operate your ve-
hicle on snowy or icy roads, INFINITI recom-
mends the use of MUD & SNOW or ALL
SEASON TIRES on all four wheels. It is rec-
ommended that you visit an INFINITI retailer
for the tire type, size, speed rating and
availability information.
2. For additional traction on icy roads, studded tires may be used. However, some U.S.
states and Canadian provinces prohibit their
use. Check local, state and provincial laws
before installing studded tires.
Skid and traction capabilities of studded snow
tires, on wet or dry surfaces, may be poorer than
that of non-studded snow tires.
3. Tire chains may be used if desired. Make sure they are the proper size for the tires on
your vehicle and are installed according to
the chain manufacturer’s instructions. Use
chain tensioners when recommended by the
tire chain manufacturer to ensure a tight fit. Loose end links of the tire chains must be
secured or removed to prevent the possibil-
ity of whipping action damage to the fenders
or underbody. In addition, drive at a reduced
speed, otherwise, your vehicle may be dam-
aged and/or vehicle handling and perfor-
mance may be adversely affected.
SPECIAL WINTER EQUIPMENT
It is recommended that the following items be
carried in the vehicle during the winter:
•A scraper and stiff-bristled brush to remove
ice and snow from the windows.
•A sturdy, flat board to be placed under the
jack to give it firm support.
•A shovel to dig the vehicle out of snowdrifts.
•Extra washer fluid to refill the windshield
washer fluid reservoir.
DRIVING ON SNOW OR ICE
WARNING
•Wet ice (32°F, 0°C and freezing rain), very
cold snow or ice can be slick and very hard
to drive on. The vehicle will have much less
traction or “grip” under these conditions.
Try to avoid driving on wet ice until the road
is salted or sanded.
•Whatever the condition, drive with caution.
Accelerate and slow down with care. If ac-
celerating or downshifting too fast, the
drive wheels will lose even more traction.
•Allow more stopping distance under these
conditions. Braking should be started
sooner than on dry pavement.
•Allow greater following distances on slip-
pery roads.
•Watch for slippery spots (glare ice). These
may appear on an otherwise clear road in
shaded areas. If a patch of ice is seen ahead,
brake before reaching it. Try not to brake
while on the ice, and avoid any sudden
steering maneuvers.
•Do not use cruise control on slippery roads.
•Snow can trap dangerous exhaust gas un-
der your vehicle. Keep snow clear of the
exhaust pipe and from around your vehicle.
5-94Starting and driving

6 In case of emergency
Hazard warning flasher switch...............6-2
Flat tire ............................ .6-2
Tire Pressure Monitoring System (TPMS) .......6-2
Stopping vehicle .................... .6-3
Warning triangle (if equipped) .............6-4
Run-flat tires ....................... .6-4Removing and fitting wheels
..............6-5
Jump starting .........................6-10
Push starting .........................6-12
If your vehicle overheats ..................6-13
Towing your vehicle .................... .6-14
Towing recommended by INFINITI ...........6-14

will flash for approximately 1 minute. The
light will remain on after 1 minute. It is rec-
ommended you Contact an INFINITI retailer
as soon as possible for tire replacement
and/or system resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•If you used Emergency Tire Sealant to repair
a minor tire puncture, the TPMS sensor
should be checked when repairing or re-
placing the tire. It is recommended you visit
an INFINITI retailer for this service.
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the low
tire pressure warning light is lit, and a tire
pressure-related warning (if equipped) appears
in the vehicle information display, one or more
of your tires is significantly under-inflated. If
the vehicle is being driven with low tire pres-
sure, the TPMS will activate and warn you of it
by the low tire pressure warning light (in the
meter panel). This system will activate only
when the vehicle is driven at speeds above 16
MPH (25 km/h). For more details about the TPMS, see
Tire
Pressure Monitoring System (TPMS) in the
5. Starting and driving section.
STOPPING VEHICLE
WARNING
•Be sure to apply the parking brake firmly.
•Be sure that P (Park) is engaged.
•Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazard-
ous.
•Never change tires when the oncoming traf-
fic is close to your vehicle. Call for profes-
sional road assistance.
1. Safely move the vehicle off the road away from traffic.
2. Turn on the hazard indicator flasher lights.
3. Park on a level surface.
4. Apply the parking brake.
5. Press the P (Park) button.
6. Turn off the engine. 7. Open the hood and set up the triangle
reflector (if equipped):
•To warn other traffic.
•To signal professional road assistance
personnel that you need assistance.
8. Have all passengers get out of the vehicle and stand in a safe place, away from other
traffic and clear of the vehicle.
In case of emergency6-3

In addition to the vehicle load, the driving
distance possible depends upon:
•Vehicle speed.
•Road condition.
•Outside temperature.
The driving distance possible in run-flat mode
may be reduced by extreme driving conditions/
maneuvers, or it can be increased through a
moderate style of driving.
The driving distance possible in run-flat mode is
counted from the moment the tire pressure loss
warning appears in the vehicle information dis-
play.
You must not exceed a maximum speed of 50
MPH (80 km/h).
When replacing one or all tires, observe the
following specifications for your vehicle’s tires:
•Size
•Type
•Run-flat mark
If a tire has gone flat and cannot be replaced
with a run flat tire, a standard tire may be used
as a temporary measure. Make sure that you
use the proper size and type (summer or winter
tire).
WARNING
Do not exceed the stated maximum speed.
Avoid abrupt steering and driving maneuvers,
and driving over obstacles (curbs, pot holes,
off road). This applies in particular to a laden
vehicle.
Stop driving in emergency mode if:
•You hear banging noises.
•The vehicle starts to shake.
•You see smoke and smell rubber.
•VDC is intervening constantly.
•There are tears in the sidewalls of the tire.
After driving in emergency mode, have the
wheel rims checked with regard to their further
use. It is recommended you visit an INFINITI
retailer for this service. The faulty tire must be
replaced.
REMOVING AND FITTING WHEELS
NOTE
A spare wheel is not provided with your vehicle.
Blocking the wheels
WARNING
Make sure to block the appropriate wheel to
prevent the vehicle from moving, which may
cause personal injury.
Place suitable blocks
1in front of and behind
the wheel diagonally opposite the flat tire
Ato
prevent the vehicle from moving when it is on
the jack.
MCE0001DZ
In case of emergency6-5