light INFINITI QX30 2017 Owners Manual

Symptom Possible causeRemedy
The engine
cannot be
started using
the keyThe on-board
voltage is too
low
•Switch off non-essential consumers, e. g. seat heating or interior lighting, and try to start the engine again
If this does not work:
•Check the starter battery and charge it if necessary (seeBatteryin the8. Do-it-yourselfsection)
or
•Jump-start the vehicle (seeJump startingin the6. In case of emergencysection)
or
•Have the system checked. It is recommended you consult an INFINITI retailer.
You have lost
a key—
•Have the key deactivated. It is recommended you visit an INFINITI retailer for this service.•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well
You have lost
the emer-
gency key
element
•Report the loss immediately to the vehicle insurers•If necessary, have the locks changed as well.
Pre-driving checks and adjustments3-13

1. Make sure that the windshield wipers are
switched off.
2. Pull the hood lock release lever
1, located
below the instrument panel on the driver’s
side; the hood will spring up slightly.3. Push the lever
2at the front of the hood,
to the left with your fingertips and raise the
hood.4. Insert the support rod3into the slot4on the underside of the hood.
5. When closing the hood, replace the support
rod in its original position
5, slowly lower
the hood to about8–12in.(20–30cm)
above the hood lock, then let it drop. Make
sure the hood is securely latched.
WARNING
•Make sure the hood is completely closed
and latched before driving. Failure to do so
could cause the hood to fly open and result
in an accident.
•If you see steam or smoke coming from the
engine compartment, to avoid injury do not
open the hood.
NDI1603NDI1627NDI1605
HOOD
3-14Pre-driving checks and adjustments

VANITY MIRROR
To use the front vanity mirror3, pull down the
sun visor
1and pull up the cover4.
AUTOMATIC ANTI-GLARE REAR VIEW
MIRROR
The inside mirror is designed so that it auto-
matically dims according to the intensity of the
headlights of the vehicle following you. The
automatic anti-glare feature operates only when
the ignition switch is in the ON position. It will
not operate if reverse gear is engaged or if the
interior lighting is switched on.
OUTSIDE MIRRORS
The driver’s-side outside mirror is designed so
that it automatically dims according to the inten-
sity of the headlights of the vehicle following you.
The automatic anti-glare feature operates only
when the ignition switch is in the ON position. It
will not operate if reverse gear is engaged or if
the interior lighting is switched on.
Adjusting
The outside rear view mirror remote control will
operate only when the ignition switch is in the
ACC or ON position.
1. Move the switch to select the left
1or right
mirror
2.
2. Adjust each mirror to the desired position
using the large switch
3.
Defogging
The exterior rear view mirrors will be heated
when the rear window defogger switch is oper-
ated.
NIC2676NDI1630NIC2636
MIRRORS
Pre-driving checks and adjustments3-17

Clock settings
Clock settings can be changed.
1. Push

Backing up near a projecting object
The predicted course linesAdo not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
moving course.
Backing up behind a projecting
object
The positionCis shown further than the
position
Bin the display. However, the posi-
tion
Cis actually at the same distance as theposition
A. The vehicle may hit the object
when backing up to the position
Aif the object
projects over the actual moving course.
HOW TO PARK WITH PREDICTED
COURSE LINES
WARNING
•If the tires are replaced with different sized
tires, the predicted course line may not be
displayed correctly.
•On a snow-covered or slippery road, there
may be a difference between the predicted
course line and the actual course line.
•The displayed lines will appear slightly off
to the right because the rear view camera is
not installed in the rear center of the ve-
hicle.
•If the battery is disconnected or becomes
discharged, the predicted course lines may
be displayed incorrectly. If this occurs,
please perform the following procedures:
–Turn the steering wheel from lock to lock
while the engine is running.
–Drive the vehicle on a straight road for
more than 5 minutes.
SAA1923SAA1980
4-20Display screen, heater and air conditioner, and audio system

•Objects in the RearView Monitor will appear
visually opposite than when viewed in the
rear view and outside mirrors.
•Use the displayed lines as a reference. The
lines are highly affected by the number of
occupants, fuel level, vehicle position, road
conditions and road grade.
•Make sure that the lift gate is securely
closed when backing up.
•Do not put anything on the rear view cam-
era. The rear view camera is installed above
the license plate.
•When washing the vehicle with high-
pressure water, be sure not to spray it
around the camera. Otherwise, water may
enter the camera unit causing water con-
densation on the lens, a malfunction, fire or
an electric shock.
•Do not strike the camera. It is a precision
instrument. Otherwise, it may malfunction
or cause damage resulting in a fire or an
electric shock.The following are operating limitations and do
not represent a system malfunction:
•When the temperature is extremely high or
low, the screen may not clearly display ob-
jects.
•When strong light shines directly on to the
camera, objects may not be displayed
clearly.
•Vertical lines may be seen in objects on the
screen. This is due to strong reflected light
from the bumper.
•The screen may flicker under fluorescent
light.
•The colors of objects on the RearView Moni-
tor may differ somewhat from the actual
color of objects.
•Objects on the monitor may not be clear in a
dark environment.
•Do not use wax on the camera window. Wipe
off any wax with a clean cloth dampened
with mild detergent diluted with water.
SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the camera. This will cause discolou-
ration. To clean the camera, wipe with a
cloth dampened with diluted mild cleaning
agent and then wipe with a dry cloth.
•Do not damage the camera as the monitor
screen may be adversely affected.
If dirt, rain or snow accumulates on the camera
1, the RearView Monitor may not display
objects clearly. Clean the camera by wiping it
with a cloth dampened with a diluted mild
cleaning agent and then wiping it with a dry
cloth.
NAA1688
4-24Display screen, heater and air conditioner, and audio system

•The distance between objects viewed in the
rear view differs from actual distance be-
cause a wide-angle lens is used.
•The displayed lines on the rear view will
appear slightly off to the right because the
rear view camera is not installed in the rear
center of the vehicle.
Front view Rear view
Front and rear views:
Guiding lines, which indicate the vehicle width and
distances to objects with reference to the vehicle
body line
A, are displayed on the monitor.
Distance guide lines:
Indicate distances from the vehicle body:
•Red line1: approx.1.5 ft (0.5 m)
•Yellow line2: approx. 3 ft (1 m)
•Green line3: approx. 7 ft (2 m)
•Green line4: approx. 10 ft (3 m)
Vehicle width guide lines
5:
Indicate the approximate vehicle width when
backing up.Predicted course lines
6:
Indicate the predicted course when operating the
vehicle. The predicted course lines will be dis-
played on the monitor when the steering wheel is
turned. The predicted course lines will move
depending on how much the steering wheel is
turned and will not be displayed while the steer-
ing wheel is in the straight ahead position.
The front view will not be displayed when the
vehicle speed is above 10 km/h (6 MPH).
NOTE
When the monitor displays the front view and
the steering wheel turns about 90 degrees or
less from the neutral position, both the right and
left predicted course lines
6are displayed.
When the steering wheel turns about 90 degrees
or more, a line is displayed only on the opposite
side of the turn.
SAA1840ZSAA1896Z
Display screen, heater and air conditioner, and audio system4-27

Bird’s-eye view:
WARNING
•Objects in the bird’s-eye view will appear
farther than the actual distance.
•Tall objects, such as a curb or a vehicle, may
be misaligned or not displayed at the seam
of the views.
•Objects that are above the camera cannot
be displayed.
•The view for the bird’s-eye view may be
misaligned when the camera position al-
ters.
•A line on the ground may be misaligned and
is not seen as being straight at the seam of
the views. The misalignment will increase
as the line proceeds away from the vehicle.
•Tire angle display does not indicate the
actual tire angle.
The bird’s-eye view shows the overhead view of the
vehicle, which helps confirm the vehicle position.
The vehicle icon1shows the position of the
vehicle.
NOTE
The size of the vehicle icon on the bird’s-eye view
may differ somewhat from the actual vehicle.
The areas that the cameras cannot cover2are
indicated in black.
The non-viewable area
2is highlighted in
yellow for several seconds after the bird’s-eye
view is displayed. It will be shown only the first
time after the ignition switch is placed in the ON
position.
When the corner of the vehicle moves closer to
an object, the corner sensor indicator
3ap-
pears.Front-side view
:
Guiding lines that indicate the approximate
width and the front end of the vehicle are
displayed on the monitor.
The front-of-vehicle line
1shows the front part
of the vehicle.
The side-of-vehicle line
2shows the approxi-
mate vehicle width including the outside mir-
rors.
The extensions
3of both the front1and side
2lines are shown with a green dotted line.
The corner sensor indicator
4will appear
when a corner of the vehicle moves closer to an
object.
NAA1681SAA1842ZLeft-Hand Drive (LHD) models*
4-28Display screen, heater and air conditioner, and audio system

Backing up near a projecting object
The predicted course linesAdo not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
moving course.
Backing up behind a projecting
object
The positionCis shown farther than the
position
Bin the display. However, the posi-
tion
Cis actually at the same distance as theposition
A. The vehicle may hit the object
when backing up to the position
Aif the object
projects over the actual moving course.
HOW TO PARK WITH PREDICTED
COURSE LINES
WARNING
•If the tires are replaced with different sized
tires, the predicted course lines may not be
displayed correctly.
•On a snow-covered or slippery road, there
may be a difference between the predicted
course lines and the actual course.
•The displayed lines will appear slightly off
to the right because the rear view camera is
not installed in the rear center of the ve-
hicle.
•If the battery is disconnected or becomes
discharged, the predicted course lines may
be displayed incorrectly. If this occurs,
please perform the following procedures:
–Turn the steering wheel from lock to lock
while the engine is running.
–Drive the vehicle on a straight road for
more than 5 minutes.
SAA1923SAA1980
4-30Display screen, heater and air conditioner, and audio system

AROUND VIEW®MONITOR SYSTEM
LIMITATIONS
WARNING
Listed below are the system limitations for
Around View Monitor. Failure to operate the
vehicle in accordance with these system limi-
tations could result in serious injury or death.
•Do not use the Around View Monitor with
the outside mirror in the stored position,
and make sure that the lift gate is securely
closed when operating the vehicle using the
Around View Monitor.
•The apparent distance between objects
viewed on the Around View Monitor differs
from the actual distance.
•The cameras are installed on the front
grille, the outside mirrors and above the
rear license plate. Do not put anything on
the cameras.
•When washing the vehicle with high-
pressure water, be sure not to spray it
around the cameras. Otherwise, water may
enter the camera unit causing water con-
densation on the lens, a malfunction, fire or
an electric shock.
•Do not strike the cameras. They are preci-sion instruments. Doing so could cause a
malfunction or cause damage resulting in a
fire or an electric shock.
The following are operating limitations and do
not represent a system malfunction:
•There may be a delay when switching be-
tween views.
•When the temperature is extremely high or
low, the screen may not display objects
clearly.
•When strong light is directly shines on the
camera, objects may not be displayed
clearly.
•The screen may flicker under fluorescent
light.
•The colors of objects on the Around View
Monitor may differ somewhat from the actual
color of objects.
•Objects on the monitor may not be clear and
the color of the object may differ in a dark
environment.
•There may be differences in sharpness
between each camera view of the bird’s-eye
view.
•Do not use wax on the camera lens. Wipe off
any wax with a clean cloth that has been
dampened with a diluted mild cleaning
agent, then wipe with a dry cloth.
4-34Display screen, heater and air conditioner, and audio system