ECU INFINITI QX30 2017 Manual PDF

[ICC Currently Unavailable See Operator’s
Manual]:The ICC system is temporarily inopera-
tive. Possible causes:
•The function is impaired due to heavy rain or
snow.
•The radar sensor system is temporarily
inoperative, e. g. due to electromagnetic
radiation emitted by nearby TV or radio sta-
tions or other sources of electromagnetic
radiation.
•The system is outside the operating tem-
perature range.
•The on-board voltage is too low.
A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out.
If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Restart the engine.[ICC Inoperative]:The ICC system is malfunc-
tioning. The adaptive brake assist function may
also have failed. A warning tone also sounds.
Have the system checked. It is recommended
you visit an INFINITI retailer for this service.
[ICC Suspended]:You have depressed the accel-
erator pedal. The ICC system is no longer
controlling the speed of the vehicle.
The display message should disappear when
you remove your foot from the accelerator pedal
[ICC–––MPH]:An activation condition for the
ICC system is not fulfilled.
Check the activation conditions for the ICC
system.
SYSTEM MAINTENANCE
The sensor for the ICC systemAis located
behind the INFINITI logo at the front of the
vehicle.
To keep the ICC system operating properly, be
sure to observe the following:
•Always keep area around the sensor clean.
•Do not strike or damage the areas around
the sensor. Do not touch or remove the screw
located on the sensor. Doing so could cause
failure or malfunction. If the sensor is dam-
aged due to an accident, it is recommended
you contact an INFINITI retailer.
•Do not cover or attach stickers (including
transparent material) or install an accessory
near the sensor. This could cause failure or
malfunction.
NSD645
Starting and driving5-59

SYSTEM TEMPORARILY UNAVAILABLE
If the FEB stops working due to a malfunction or
some other reason, one of the following three
messages will be displayed in the vehicle infor-
mation display.
•[Emergency Brake Currently Unavailable See
Operator’s Manual]
•[Emergency Brake Inoperative]
•[Radar Sensors Dirty See Operator’s Manual]
For each of these messages, possible causes
and solutions are listed below.
[Emergency Brake Currently Unavailable See
Operator’s Manual]:The FEB system is tempo-
rarily inoperative. Possible causes:
•The radar sensor system is temporarily
inoperative, for example, due to electromag-
netic radiation emitted by nearby TV or radio
stations or other sources of electromagnetic
radiation.
•The system is outside the operating tem-
perature range.
•The on-board voltage is too low.
Once the causes listed above no longer apply,
the display message goes out. The FEB system
is operative again.If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
[Emergency Brake Inoperative]:The FEB system
is temporarily inoperative due to a malfunction.
The adaptive brake assist function may also
have failed.
It is recommended you visit an INFINITI retailer.
[Radar Sensors Dirty See Operator’s Manual]:
The FEB system is temporarily restricted or
inoperative. Possible causes:
•The sensor behind the INFINITI logo is dirty.
•The function of the FEB system is impaired
due to heavy rain or snow.
A warning tone also sounds.
Once the causes listed above no longer apply,
the display message goes out. The FEB system
is operative again.If the display message does not disappear:
•Pull over and stop the vehicle safely as soon
as possible, paying attention to road and
traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
•Clean the area around the sensors.
•Restart the engine. The display message
disappears.
Starting and driving5-65

7. Stop as soon as the parking sensor system
sounds the continuous warning tone, if not
before. Maneuvering may be required in
tight parking spaces.
The [Park Assist active Select D Observe
surroundings] message appears in the ve-
hicle information display.
8. Select transmission position D (Drive) while
the vehicle is stationary.
IPA immediately steers in the other direction.
The [Park Assist Observe surroundings] mes-
sage appears in the vehicle information dis-
play.
NOTE
You will achieve the best results by waiting
for the steering procedure to complete before
pulling away.
9. Drive forwards and be ready to brake at all
times.
Maneuvering may be required in tight park-
ing spaces. Drive forward and back up as
prompted by the parking sensor system
warning displays, several times if necessary.10. Stop as soon as the parking sensor system
sounds the continuous warning tone, if not
before.
The [Park Assist active Select R] [Observe
surroundings] message appears in the ve-
hicle information display.
As soon as the parking procedure is com-
plete the [Park Assist switched off] mes-
sage appears and a warning tone sounds.
The vehicle is now parked.
11. Before leaving the vehicle, secure the ve-
hicle against rolling away unintentionally:
•The electric parking brake must be applied.
•The transmission must be in position P
(Park) and the transmission position dis-
play must show P in the vehicle informa-
tion display.
•The key must be removed from the
ignition switch.
•On uphill or downhill gradients, the front
wheels must be turned towards the curb.
IPA no longer supports you with steering inter-
ventions. When IPA is finished, you must steer
again yourself. The parking sensor system is
still available.Parking tips:
•The way your vehicle is positioned in the
parking space after parking is dependent on
various factors. These include the position
and shape of the vehicles parked in front and
behind it and the conditions of the location.
It may be the case that IPA guides you too far
into a parking space, or not far enough into
it. In some cases, it may also lead you across
or onto the curb. If necessary you should
cancel the parking procedure with IPA.
•During the parking maneuver, the system
will indicate when you should shift to R
(Reverse) or D (Drive). However, you can
freely choose to shift gear whenever you feel
you need to. Should the transmission change
take place too early, the parking procedure
will be canceled. A sensible parking position
can no longer be achieved from this position.
Starting and driving5-71

CAUTION
Always secure the vehicle correctly against
rolling away. Otherwise, the vehicle or its drive
train could be damaged.
To ensure that the vehicle is secured against
rolling away unintentionally:
•The electric parking brake must be applied.
•The transmission must be in position P
(Park) and the transmission position display
must show P in the vehicle information dis-
play.
•The key must be removed from the ignition
switch.
•On uphill or downhill gradients, the front
wheels must be turned towards the curb.1. Firmly apply the parking brake.
2. Press the P (Park) button.
3. To help prevent the vehicle from moving into
traffic when parked on an incline, it is a good
practice to turn the wheels as illustrated.
HEADED DOWNHILL WITH CURB
1
Turn the wheels into the curb and move the
vehicle forward until the curb side wheel
gently touches the curb. Then apply the
parking brake.
HEADED UPHILL WITH CURB
2
Turn the wheels away from the curb and
allow the vehicle to move back until the curb
side wheel gently touches the curb. Then
apply the parking brake.HEADED UPHILL OR DOWNHILL, WITHOUT
CURB
3
Turn the wheels toward the side of the road
so the vehicle will move away from the
center of the road if the vehicle moves. Then
apply the parking brake.
4. Put the ignition switch in the OFF position.
SWITCHING OFF THE ENGINE
WARNING
The automatic transmission switches to posi-
tion N (Neutral) when you switch off the en-
gine. The vehicle may roll away. There is a risk
of an accident.
After switching off the engine, always switch
to position P (Park). Prevent the parked vehicle
from rolling away by applying the parking
brake.
Procedure
1. Apply the electric parking brake.
2. Shift the transmission to position P (Park).
3.With the key:turn the key to the position
OFF in the ignition switch and remove it The
immobilizer is activated.
SSD0488Z
Starting and driving5-85

TIRE EQUIPMENT
1. SUMMER tires have a tread designed to
provide superior performance on dry pave-
ment. However, the performance of these
tires will be substantially reduced in snowy
and icy conditions. If you operate your ve-
hicle on snowy or icy roads, INFINITI recom-
mends the use of MUD & SNOW or ALL
SEASON TIRES on all four wheels. It is rec-
ommended that you visit an INFINITI retailer
for the tire type, size, speed rating and
availability information.
2. For additional traction on icy roads, studded
tires may be used. However, some U.S.
states and Canadian provinces prohibit their
use. Check local, state and provincial laws
before installing studded tires.
Skid and traction capabilities of studded snow
tires, on wet or dry surfaces, may be poorer than
that of non-studded snow tires.
3. Tire chains may be used if desired. Make
sure they are the proper size for the tires on
your vehicle and are installed according to
the chain manufacturer’s instructions. Use
chain tensioners when recommended by the
tire chain manufacturer to ensure a tight fit.
Loose end links of the tire chains must be
secured or removed to prevent the possibil-
ity of whipping action damage to the fendersor underbody. In addition, drive at a reduced
speed, otherwise, your vehicle may be dam-
aged and/or vehicle handling and perfor-
mance may be adversely affected.
SPECIAL WINTER EQUIPMENT
It is recommended that the following items be
carried in the vehicle during the winter:
•A scraper and stiff-bristled brush to remove
ice and snow from the windows.
•A sturdy, flat board to be placed under the
jack to give it firm support.
•A shovel to dig the vehicle out of snowdrifts.
•Extra washer fluid to refill the windshield
washer fluid reservoir.
DRIVING ON SNOW OR ICE
WARNING
•Wet ice (32°F, 0°C and freezing rain), very
cold snow or ice can be slick and very hard
to drive on. The vehicle will have much less
traction or “grip” under these conditions.
Try to avoid driving on wet ice until the road
is salted or sanded.
•Whatever the condition, drive with caution.
Accelerate and slow down with care. If ac-
celerating or downshifting too fast, the
drive wheels will lose even more traction.
•Allow more stopping distance under these
conditions. Braking should be started
sooner than on dry pavement.
•Allow greater following distances on slip-
pery roads.
•Watch for slippery spots (glare ice). These
may appear on an otherwise clear road in
shaded areas. If a patch of ice is seen ahead,
brake before reaching it. Try not to brake
while on the ice, and avoid any sudden
steering maneuvers.
•Do not use cruise control on slippery roads.
•Snow can trap dangerous exhaust gas under
your vehicle. Keep snow clear of the exhaust
pipe and from around your vehicle.
5-94Starting and driving

WARNING TRIANGLE (IF EQUIPPED)
Removing and refitting the warning
triangle
To remove:
1. Open the lift gate and lift the luggage
compartment floor upwards.2. To release warning triangle, push back the
retainers on the bracket.
3. Remove warning triangle
1from the
bracket.
To refit:
1. Place warning triangle
1back into the
bracket and push down to secure.
2. Fold down the luggage compartment floor.
3. Close the lift gate.
Setting up the warning triangle
1. Fold legs out to the side.
2. Fold side reflectors upwards to form a
triangle and lock them at the top using press
stud.
RUN-FLAT TIRES
With special run-flat tires, you can continue to
drive your vehicle even if there is a total loss of
pressure in one or more tires. The affected tire
must not show any clearly visible damage.
You can recognise run-flat tires by the marking
which appears on the tire side wall. You will
find this marking next to the tire size designa-
tion, the load-bearing capacity and the speed
index.Run-flat tires may only be used in conjunction
with an activated tire pressure loss warning
system or tire pressure monitor.
Pressure loss warning message
If a pressure loss warning message appears in
the vehicle information display:
•Observe the instructions in the display
messages.
•Check the tire for damage.
•If driving on, observe the following notes.
The driving distance possible in run-flat mode is
approximately 50 miles (80 km) when the ve-
hicle is partially laden and approximately 20
miles (30 km) when the vehicle is fully laden.
In addition to the vehicle load, the driving
distance possible depends upon:
•Vehicle speed.
•Road condition.
•Outside temperature.
The driving distance possible in run-flat mode
may be reduced by extreme driving conditions/
maneuvers, or it can be increased through a
moderate style of driving.NIC2686
6-4In case of emergency

2. Align the center of both the jack head2and the notches at the jack-up point3as
shown.
3. Fit the groove of the jack head between the
two notches as shown.4. Loosen each wheel bolt by one or two turns
counterclockwise with the wheel wrench.
Do not remove the wheel bolts until the tire is
off the ground.
Models with wheel lock bolts (if equipped) :
If the wheel is equipped with a wheel lock
bolt, insert the wheel lock key
1and
loosen it as previously described.
The wheel lock bolt can only be removed
with the wheel lock key. A key number is
necessary if you need to duplicate the wheel
lock key.Record the key number as shown on the key
code card on the “Security information”
page at the end of this manual and keep it in
a safe place, not in the vehicle. If you lose
the wheel lock key, it is recommended you
see your INFINITI retailer for a duplicate with
the original wheel lock key code.
Make sure to keep the lock key in the
vehicle. Otherwise, wheels cannot be re-
moved and the service cannot be performed.
NCE449NCE143Z
In case of emergency6-7

5. To lift the vehicle, securely hold and turn the
ratchet handle
1clockwise as shown.
6. Carefully raise the vehicle until the tire
clears the ground.
7. Remove the wheel bolts, then remove the
wheel with the flat tire.
WARNING
The wheel is heavy. Be sure that your feet are
clear of the wheel and use gloves as necessary
to avoid injury.
Installing the wheel
WARNING
•A temporary use spare wheel and tire is
designed for emergency use.
•Never use wheel bolts other than those
provided with your vehicle. Incorrect wheel
bolts or improperly tightened wheel bolts
may cause the wheel to become loose or
come off. This could cause an accident.
•Never use oil or grease on the wheel bolts.
This may cause the wheel bolts to become
loose.ATighten
BLoosen
1. Clean any mud or dirt from the surface
between the wheel and the hub.
2. Carefully fit the wheel and tighten the wheel
bolts with your fingers. Check that all the
wheel bolts contact the wheel surface hori-
zontally and on the bevelled side.
Models with wheel lock bolt (if equipped):
Insert the wheel lock key into the wheel lock
bolt and tighten into the wheel finger tight.
3. With the wheel wrench, tighten the wheel
bolts alternately and evenly in the sequence
as illustrated (
1-5) until they are tight.
4. Lower the vehicle slowly until the tire
touches the ground.
NCE449NCE435
6-8In case of emergency

5. Tighten the wheel bolts securely using the
wheel wrench in the sequence as illustrated.
6. Lower the vehicle completely.
7. Install the wheel cover (if equipped).
Wheel
bolt tightening torque: 96 ft-lb (130 N•m, 13
kg-m)
As soon as possible, tighten the wheel bolts to
the specified torque with a torque wrench.
The wheel bolts must be kept tightened to
specification at all times. It is recommended
that the wheel bolts be tightened to specifica-
tion at each maintenance interval.
Adjust the tire pressure to the COLD pressure.
COLD pressure is the tire pressure as measured
after the vehicle has been parked for three hours
or more or driven for less than 1 mile (1.6 km).
COLD tire pressures are shown on the tire and
loading information label affixed to the driver’s
side center pillar.
Wheel lock bolts(if equipped)
In order to prevent theft, the specially designed
wheel lock bolt is installed to each wheel. The
wheel lock bolt cannot be removed with the
commonly used tools.
When removing tires, use the lock key provided
with your vehicle.Removing the wheel lock bolt
:
1. Insert the wheel lock key1to the wheel
lock bolt.
2. To remove the wheel lock bolt, turn the
wheel lock key counterclockwise using the
wheel wrench.
CAUTION
•Do not use a power tool to remove the wheel
lock bolts.
•When installing the wheel, tighten the
wheel lock bolts to the same tightening
torque as the normal wheel bolts. For de-
tails, seeInstalling the wheelearlier in
this section.NOTE
•The wheel lock bolt has an individual code.
A wheel lock key with other than the indi-
vidual code cannot remove the wheel lock
bolt. If you lose the wheel lock key, it is
recommended you contact an INFINITI re-
tailer for a duplicate with the original wheel
lock key code.
•Record the key number and keep it in a safe
place, not in the vehicle.
•When you ask for a service at an INFINITI
retailer, make sure to keep the lock key in
the vehicle. Otherwise, wheels cannot be
removed and the service cannot be per-
formed.
NCE143Z
In case of emergency6-9

•Only use devices specifically designed for
vehicle recovery and follow the manufactur-
er’s instructions.
•Always pull the recovery device straight out
from the front of the vehicle. Never pull at an
angle.
•Route recovery devices so they do not touch
any part of the vehicle except the attach-
ment point.
If your vehicle is stuck in sand, snow, or mud,
and the vehicle is unable to free itself without
being pulled, use the recovery hook stored in
the vehicle trunk.
WARNING
•Use the recovery hook only. Do not attach
the pulling device to any other part of the
vehicle body. Otherwise, the vehicle body
may be damaged.
•Use the recovery hook to free a vehicle only.
Never tow a vehicle using only the recovery
hook.
•The recovery hook is under tremendous
stress when used to free a trapped vehicle.
Always pull the pulling device straight out
from the vehicle. Never pull on the recovery
hook at an angle.
Securely install the recovery hook (stored in the
vehicle trunk) to the attaching mount located on
the front or rear bumper.
Make sure that the recovery hook is properly
secured in its storage location after use and the
license plate is properly reinstalled before driv-
ing the vehicle.
Rocking a stuck vehicle
WARNING
•To avoid potential injury, stand clear of a
stuck vehicle.
•Do not spin your tires at high speed. This
could cause them to explode and result in
serious injury. Parts of your vehicle could
also overheat and be damaged.If your vehicle is stuck in sand, snow, mud, etc.,
use the following procedure:
1. Turn off the Vehicle Dynamic Control (VDC)
system.
2. Make sure the area in front and behind the
vehicle is clear of obstructions.
3. Turn the steering wheel right and left to
clear an area around the front tires.
4. Slowly rock the vehicle forward and back-
ward.
•Shift back and forth between R (Reverse)
and D (Drive).
•Apply the accelerator as little as possible to
maintain the rocking motion.
•Release the accelerator pedal before shifting
between R (Reverse) and D (Drive).
•Do not spin the tires above 35 MPH (55
km/h).
5. If the vehicle cannot be freed after a few
tries, contact a professional towing service
to remove the vehicle.
6-16In case of emergency