ECU INFINITI QX30 2017 Owners Manual

1. Rear armrest* (P. 1-7)
2. Rear personal lights (P. 2-85)
3. Overhead control panel (P. 2-74)
4. Sunshade switch* (P. 2-74)
5. Sun visor (P. 2-16)
6. Security system buttons (P. 3-57)7. Interior rear-view mirror (P. 3-17)
8. Door handle (P. 3-6)
9. Door armrest
— Power windows controls (P. 2-71)
— Exterior rear view mirror remote control
switch (P. 2-17)10. Front cup holders (P. 2-78)
11. Air conditioner controls (P. 4-43)
12. Glove box/storage (P. 2-77)
*: if equipped
NIC2701
PASSENGER COMPARTMENT
Illustrated table of contents0-5

WARNING
•The seatback should not be reclined any
more than needed for comfort. Seat belts
are most effective when the passenger sits
well back and straight up in the seat. If the
seat back is reclined, the risk of sliding un-
der the lap belt and being injured is in-
creased.
•For the most effective protection when the
vehicle is in motion, the seat should be up-
right. Always sit well back and upright in the
seat with both feet on the floor and adjust
the seat properly. (SeeSeat beltslater in
this section.)
•After adjustment, gently rock in the seat to
make sure it is securely locked.
•To help avoid risk of injury or death through
unintended operation of the vehicle and/or
its systems, do not leave children, people
who require the assistance of others, or
pets unattended in your vehicle. Addition-
ally, the temperature inside a closed vehicle
on a warm day can quickly become high
enough to cause a significant risk of injury
or death to people and pets.
•Do not leave children unattended inside the
vehicle. They could unknowingly activate
switches or controls. Unattended children
could become involved in serious accidents.
•Do not adjust the driver’s seat while driving
so full attention may be given to vehicle
operation. The seat may move suddenly and
could cause loss of control of the vehicle.
CAUTION
When adjusting the seat positions, be sure not
to contact any moving parts to avoid possible
injuries and/or damage.
SSS0133AZ
SEATS
1-2Safety — seats, seat belts and supplemental restraint system

Lumbar support:
The lumbar support feature provides lower back
support to the driver.
Push each side of the adjusting switch to adjust
the seat lumbar area until the desired position
is achieved.
1To raise the seatback contour
2To soften the seatback contour
3To lower the seatback contour
4To harden the seatback contour
SEAT HEATER (IF EQUIPPED)
The seats can be warmed by built-in heaters. The
switches are located on the center console (for
front seats) and can be operated independently
of each other. For more information on the seat
heater, seeSeat heating (if equipped)in the2.
Instruments and controlssection.
REAR SEATS
WARNING
•Never allow anyone to ride in the cargo area
or on the rear seat when it is in the fold-
down position. Use of these areas by pas-
sengers without proper restraints could re-
sult in serious injury or deathin an accident
or sudden stop.
•Properly secure all cargo with ropes or
straps to help prevent it from sliding or
shifting. Do not place cargo higher than the
seatbacks. In a sudden stop or collision,
unsecured cargo could cause personal in-
jury.
•Do not allow people to ride in any area of
your vehicle that is not equipped with seats
and seat belts. Be sure everyone in your
vehicle is in a seat and using a seat belt
properly.
•Do not allow more than one person to use
the same seat belt.
•Do not fold down the rear seats when occu-
pants are in the rear seat area or any lug-
gage is on the rear seats.
–Make sure that the seat path is clear
before moving the seat.–Be careful not to allow hands or feet to
get caught or pinched in the seat.
•Head restraints/headrests should be ad-
justed properly as they may provide signifi-
cant protection against injury in an acci-
dent. Always replace and adjust them
properly if they have been removed for any
reason.
•If the head restraints/headrests are re-
moved for any reason, they should be se-
curely stored to prevent them from causing
injury to passengers or damage to the ve-
hicle in case of sudden braking or an acci-
dent.
•When returning the seatbacks to the up-
right position, be certain they are com-
pletely secured in the latched position. If
they are not completely secured, passen-
gers may be injured in an accident or sud-
den stop.
NIC2607
Safety — seats, seat belts and supplemental restraint system1-5

ARMREST (IF EQUIPPED)
Rear
Pull the tab and draw the armrest1forward
until it is horizontal.
Indicates that the seating position is
equipped with a head restraint.
Indicates that the seating position is
equipped with a non-removable head rest.
WARNING
Head restraints/headrests supplement the
other vehicle safety systems. They may pro-
vide additional protection against injury in cer-
tain rear end collisions. Adjustable head
restraints/headrests must be adjusted prop-
erly, as specified in this section. Check the
adjustment after someone else uses the seat.
Do not attach anything to the head restraint/
headrest stalks or remove the head restraint/
headrest. Do not use the seat if the head
restraint/headrest has been removed. If the
head restraint/headrest was removed, rein-stall and properly adjust the head restraint/
headrest before an occupant uses the seating
position. Failure to follow these instructions
can reduce the effectiveness of the head
restraints/headrests. This may increase the
risk of serious injury or death in a collision.
•Your vehicle is equipped with head
restraints/headrests that may be integrated,
adjustable or non-adjustable.
•Adjustable head restraints/headrests have
multiple notches along the stalk to lock them
in a desired adjustment position.
•The non-adjustable head restraints/
headrests have a single locking notch to
secure them to the seat frame.
•Proper Adjustment:
– For the adjustable type, align the head
restraint/headrest so the center of your
ear is approximately level with the center
of the head restraint/headrest.
– If your ear position is still higher than the
recommended alignment, place the head
restraint/headrest at the highest posi-
tion.
NIC2611NPA1500
HEAD RESTRAINTS/HEADRESTS
Safety — seats, seat belts and supplemental restraint system1-7

•If the head restraint/headrest has been
removed, ensure that it is reinstalled and
locked in place before riding in that desig-
nated seating position.
NOTE
For vehicles with sports seats you cannot adjust
the front head restraints/headrests or the outer
rear head restraints/headrests.
ADJUSTABLE HEAD RESTRAINT
COMPONENTS
1. Removable head restraint/headrest
2. Multiple notches
3. Lock knob
4. Stalks
REMOVE
Use the following procedure to remove the head
restraint/headrest.
1. Pull the head restraint/headrest up to the
highest position.
2. Push and hold the lock knob.
3. Remove the head restraint/headrest from
the seat.
4. Store the head restraint/headrest properly
in a secure place so it is not loose in the
vehicle.
5. Reinstall and properly adjust the head
restraint/headrest before an occupant uses
the seating position.
SSS0992ZSSS1037Z
1-8Safety — seats, seat belts and supplemental restraint system

Lower
To lower, push and hold the lock knob1and
push the head restraint/headrest down.
Make sure the head restraint/headrest is posi-
tioned so the lock knob is engaged in the notch
before riding in that designated seating posi-
tion.
Fore-aft
This function allows you to adjust the distance
between the head restraint/headrest and the
back of the head.
•To move forwards: pull the head restraint/
headrest forwards in the direction of the
arrow until it engages. There are a number of
detents.
•To move backwards: press and hold button
1and push the head restraint/headrest
backwards.
•When the head restraint/headrest is in the
desired position, release the button and
make sure that the head restraint/headrest
is engaged in position.
REAR SEAT HEAD RESTRAINTS/
HEADRESTS
Adjusting the rear seat head
restraint/headrest height
Use the head restraint/headrest in the notched
stem positions after pulling it up from the
stowed position to a position in which it locks
securely in place.
•To raise: pull the head restraint/headrest up
to the desired height.
•To lower: press release catch1and push
the head restraint/headrest down until it is
in the desired position.
SSS1036ZNIC2610NIC2609
1-10Safety — seats, seat belts and supplemental restraint system

•The seat belt should be properly adjusted
to a snug fit. Failure to do so may reduce the
effectiveness of the entire restraint system
and increase the chance or severity of injury
in an accident. Serious injury or death can
occur if the seat belt is not worn properly.
•Always route the shoulder belt over your
shoulder and across your chest. Never put
the belt behind your back, under your arm or
across your neck. The belt should be away
from your face and neck, but not falling off
your shoulder.
•Position the lap belt as low and snug as
possible AROUND THE HIPS, NOT THE
WAIST. A lap belt worn too high could in-
crease the risk of internal injuries in an ac-
cident.
•Be sure the seat belt tongue is securely
fastened to the proper buckle.
•Do not wear the seat belt inside out or
twisted. Doing so may reduce its effective-
ness.
•Do not allow more than one person to use
the same seat belt.
•Never carry more people in the vehicle than
there are seat belts.
•If the seat belt warning light glows continu-
ously while the ignition is turned ON with all
doors closed and all seat belts fastened, it
may indicate a malfunction in the system.
Have the system checked. It is recom-
mended that you visit an INFINITI retailer for
this service.
•No changes should be made to the seat belt
system. For example, do not modify the seat
belt, add material or install devices that
may change the seat belt routing or tension.
Doing so may affect the operation of the
seat belt system. Modifying or tampering
with the seat belt system may result in seri-
ous personal injury.
•Once a seat belt pretensioner has acti-
vated, they cannot be reused and must be
replaced together with the retractor. It is
recommended that you visit an INFINITI re-
tailer for this service.
•All seat belt assemblies, including retrac-
tors and attaching hardware, should be in-
spected after any collision. It is recom-
mended that you visit an INFINITI retailer for
this service. INFINITI recommends that all
seat belt assemblies in use during a colli-
sion be replaced unless the collision was
minor and the belts show no damage andcontinue to operate properly. Seat belt as-
semblies not in use during a collision
should also be inspected and replaced if
either damage or improper operation is
noted.
•All child restraints and attaching hardware
should be inspected after any collision. Al-
ways follow the restraint manufacturer’s in-
spection instructions and replacement rec-
ommendations. The child restraints should
be replaced if they are damaged.
PREGNANT WOMEN
INFINITI recommends that pregnant women use
seat belts. The seat belt should be worn snug,
and always position the lap belt as low as
possible around the hips, not the waist. Place
the shoulder belt over your shoulder and across
your chest. Never put the lap/shoulder belt over
your abdominal area. Contact your doctor for
specific recommendations.
INJURED PERSONS
INFINITI recommends that injured persons use
seat belts. Check with your doctor for specific
recommendations.
Safety — seats, seat belts and supplemental restraint system1-13

•The retractor is designed to lock during a
sudden stop or on impact. A slow pulling
motion permits the belt to move and al-
lows you some freedom of movement in
the seat.
•If the seat belt cannot be pulled from its
fully retracted position, firmly pull the belt
and release it. Then smoothly pull the belt
out of the retractor.
3. Position the lap belt portionlow and snug on
the hipsas shown4. Pull the shoulder belt portion toward the
retractor to take up extra slack. Be sure the
shoulder belt is routed over your shoulder
and across your chest.
The front passenger seat and the rear seating
positions three-point seat belts have two
modes of operation:
•Emergency Locking Retractor (ELR)
•Automatic Locking Retractor (ALR)
The ELR mode allows the seat belt to extend and
retract to allow the driver and passengers some
freedom of movement in the seat. The ELR locks
the seat belt when the vehicle slows down
rapidly or during certain impacts.The ALR mode (child restraint mode) locks the
seat belt for child restraint installation. When
the ALR mode is activated, the seat belt cannot
be extended again until the seat belt tongue is
detached from the buckle and fully retracted.
The seat belt returns to the ELR mode after the
seat belt fully retracts. For additional informa-
tion, refer toChild restraintslater in this
section. The ALR mode should be used only for
child restraint installation. During normal seat
belt use by an occupant, the ALR mode should
not be activated. If it is activated, it may cause
uncomfortable seat belt tension. It can also
change the operation of the front passenger air
bag. For additional information, refer toFront
passenger air bag and status lightin the1.
Safety — seats, seat belts and supplemental
restraint systemSafety — seats, seat belts and
supplemental restraint systemsection.WARNING
When fastening the seat belts, be certain that
the seatbacks are completely secured in the
latched position. If they are not completely
secured, passengers may be injured in an acci-
dent or sudden stop.
SSS0292ZSSS0290Z
Safety — seats, seat belts and supplemental restraint system1-15

WARNING
•After adjustment, release the adjustment
button and then try to move the shoulder
belt down to make sure that it is securely
fixed in position.
•The shoulder belt anchor height should be
adjusted to the position that is best for you.
Failure to do so may reduce the effective-
ness of the entire restraint system and in-
crease the chance or severity of injury in an
accident.
SEAT BELT EXTENDERS
If, because of body size or driving position, it is
not possible to properly fit the lap/shoulder
belt and fasten it, an extender that is compat-
ible with the installed seat belts is available
that can be purchased. The extender adds
approximately 8 in (200 mm) of length and may
be used for either the driver or front passenger
seating position. It is recommended you visit an
INFINITI retailer for assistance with purchasing
an extender if an extender is required.
WARNING
•Only INFINITI seat belt extenders, made by
the same company which made the original
equipment seat belts, should be used with
the INFINITI seat belts.
•Adults and children who can use the stan-
dard seat belt should not use an extender.
Such unnecessary use could result in seri-
ous personal injury in the event of an acci-
dent.
•Never use seat belt extenders to install
child restraints. If the child restraint is not
secured properly, the child could be seri-
ously injured in a collision or a sudden stop.
SEAT BELT MAINTENANCE
•To clean the seat belt webbing,apply a mild
soap solution or any solution recommended
for cleaning upholstery or carpets. Then wipe
with a cloth and allow the seat belts to dry in
the shade. Do not allow the seat belts to
retract until they are completely dry.
•If dirt builds up in the shoulder belt guideof
the seat belt anchors, the seat belts may
retract slowly. Wipe the shoulder belt guide
with a clean, dry cloth.
•Periodically check to see that the seat belt
and the metal components, such as buckles,
tongues, retractors, flexible wires and an-
chors, work properly. If loose parts, deterio-
ration, cuts or other damage on the webbing
is found, the entire seat belt assembly
should be replaced.
Safety — seats, seat belts and supplemental restraint system1-17

WARNING
Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR) mode
seat belts. If the seat belt becomes wrapped
around a child’s neck with the ALR mode acti-
vated, the child can be seriously injured or
killed if the seat belt retracts and becomes
tight. This can occur even if the vehicle is
parked. Unbuckle the seat belt to release the
child. If the seat belt can not be unbuckled or is
already unbuckled, release the child by cutting
the seat belt with a suitable tool (such as a
knife or scissors) to release the seat belt.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in this
manual, child safety information is available
from many other sources, including doctors,
teachers, government traffic safety offices, and
community organizations. Every child is differ-
ent, so be sure to learn the best way to trans-
port your child.
There are three basic types of child restraint
systems:
•Rear-facing child restraint
•Forward-facing child restraint
•Booster seat
The proper restraint depends on the child’s
size. Generally, infants up to about 1 year and
less than 20 lb (9 kg) should be placed in
rear-facing child restraints. Forward-facing child
restraints are available for children who out-
grow rear-facing child restraints and are at least
1 year old. Booster seats are used to help
position a vehicle lap/ shoulder belt on a child
who can no longer use a forward-facing child
restraint.
WARNING
Infants and children need special protection.
The vehicle’s seat belts may not fit them prop-
erly. The shoulder belt may come too close to
the face or neck. The lap belt may not fit over
their small hip bones. In an accident, an im-
properly fitting seat belt could cause serious or
fatal injury. Always use appropriate child
restraints.
All U.S. states and Canadian provinces or terri-
tories require the use of approved child re-
straints for infants and small children. See
Child restraintsin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion for more information.A child restraint may be secured in the vehicle
by using either the LATCH (Lower Anchor and
Tethers for CHildren) system or with the vehicle
seat belt. For additional information, refer to
Child restraintsin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion.
INFINITI recommends that all pre-teens and chil-
dren be restrained in the rear seat. Studies show
that children are safer when properly restrained
in the rear seat than in the front seat.
This is especially important because your ve-
hicle has a supplemental restraint system (air
bag system) for the front passenger. (See
Supplemental Restraint System (SRS)later in
this section.)
INFANTS
Infants up to at least 1 year old should be
placed in a rear-facing child restraint. INFINITI
recommends that infants be placed in child
restraints that comply with Federal Motor Ve-
hicle Safety Standards or Canadian Motor Ve-
hicle Safety Standards. You should choose a
child restraint which fits your vehicle and al-
ways follow the manufacturer’s instructions for
installation and use.
CHILD SAFETY
1-18Safety — seats, seat belts and supplemental restraint system