ABS INFINITI QX30 2018 User Guide

Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer.
The computer has a built-in diagnostic fea-
ture that tests the system each time you start
the engine and move the vehicle at a low
speed in forward or reverse. When the self-
test occurs, you may hear a “clunk” noise
and/or feel a pulsation in the brake pedal.
This is normal and does not indicate a mal-
function. If the computer senses a malfunc-
tion, it switches the ABS off and illuminates
the ABS warning light on the instrument
panel. The brake system then operates nor-
mally, but without anti-lock assistance. If the
ABS warning light illuminates during the self-
test or while driving, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
Normal operation
The ABS operates at speeds above 3 to 6
MPH (5 to 10 km/h). The speed varies ac-
cording to road conditions.
When the ABS senses that one or more
wheels are close to locking up, the actuator
rapidly applies and releases hydraulic pres-
sure. This action is similar to pumping the
brakes very quickly. You may feel a pulsation
in the brake pedal and hear a noise from
under the hood or feel a vibration from the
actuator when it is operating. This is normal
and indicates that the ABS is operating prop-
erly. However, the pulsation may indicate
that road conditions are hazardous and extra
care is required while driving.The Vehicle Dynamic Control (VDC) system
uses various sensors to monitor driver inputs
and vehicle motion. Under certain driving
conditions, the VDC system helps to perform
the following functions.
•Controls brake pressure to reduce wheel
slip on one slipping drive wheel so power is
transferred to a non slipping drive wheel
on the same axle.
•Controls brake pressure and engine output
to reduce drive wheel slip based on vehicle
speed (traction control function).
•Controls brake pressure at individual
wheels and engine output to help the
driver maintain control of the vehicle in the
following conditions: – understeer (vehicle tends to not follow the steered path despite increased
steering input)
– oversteer (vehicle tends to spin due to certain road or driving conditions).
The VDC system can help the driver to main-
tain control of the vehicle, but it cannot pre-
vent loss of vehicle control in all driving situ-
ations.
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
Starting and driving5-93

Allow the belts to dry completely in the shade
before using them. For additional informa-
tion, see "Seat belts" in the "1. Safety — seats,
seat belts and supplemental restraint system"
section.
WARNING
•Do not allow wet seat belts to roll up in
the retractor.
•NEVER use bleach, dye or chemical sol-
vents to clean the seat belts, since these
materials may severely weaken the seat
belt webbing.
CLEANING THE SEAT TRACKS
CAUTION
Periodically clean the seat tracks to pre-
vent reduction of ability to move the seats.
Clean periodically with a high-powered
vacuum cleaner. Dirt and debris may re-
duce the ability to adjust the seat. A wet
cleansing agent may be used if necessary.
GENUINE LEATHER SEAT
COVERS
Automotive leather is typically finished with
coatings which protect the surface from the
sun's damaging rays as well as making it re-
sistant to soiling. The finishes used in auto-
motive upholstery are unique; very different
to furniture, garment or shoe leathers.
Leather is extremely resilient and easy to
clean and maintain.
•Before cleaning leather upholstery,
vacuum it to remove dust.
•To clean leather, simply use a soft and
lint-free cloth dampened with lukewarm
water and mild soap. Do not soak the
leather.
•Use a gentle, circular motion. Do not run
the leather or apply extreme pressure
when cleaning.
•Wipe the leather again with another clean,
slightly damp cloth to remove soap resi-
due. Dry with a soft cloth.
Leather should be cleaned whenever it be-
comes soiled. Dust and dirt may harm leather
if allowed to work into the finish. Never use alcohol, cleaning solvents, oils,
varnishes or polishes on your leather, and
avoid using unknown products as they dam-
age the finish. Only use leather care agents
approved by INFINITI.
Steaming or ironing is not recommended as it
may damage the leather.
Leather is a natural product and has natural
surface properties such as unevenness in
structure, marks caused by injury, and subtle
color differences. These are characteristics of
leather and not material faults.
Leather cleaning kit (if equipped)
Spray onto the leather cleaning cloth, then
gently wipe the surface of leather. Use a dry
towel to absorb any excess moisture.
Please refer to the instruction manual pro-
vided with the leather cleaner kit.
Clean light-colored leather more frequently
because soiling on such surfaces is much
more visible.
You can obtain the leather cleaner kit from an
INFINITI retailer.
7-6Appearance and care

4. Repeatedly tap the key against your palmuntil battery
1falls out. 5. Insert the new battery with the positive
terminal facing upwards. Use a lint-free
cloth to do so.
6. Make sure that the surface of the battery is free of lint, grease and other contami-
nation.
7. Insert the front tabs of battery cover
1and then press to close it.
8. Insert emergency key element into the key (see "Mechanical key" in the "3. Pre-
driving checks and adjustments" section).
9. Check the function of all key buttons on the vehicle.
If you need assistance with replacement, it is
recommended that you visit an INFINITI re-
tailer for this service. FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.
NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause unde-
sired operation of the device.
NPA1473SPA0784Z
Do-it-yourself8-21

Use the following steps to mount the front
license plate:
Before mounting the license plate, confirm
that the following parts are enclosed in the
plastic bag:Only use the recommended mounting posi-
tion, otherwise the obstruction of the Intelli-
gent Cruise Control (ICC) sensor (if so
equipped) may result.
•License plate bracket
•License plate screws x 2
•Screw grommets x 2
1) Park the vehicle on flat, level ground.
2) Locate the center position
Aas illus-
trated. Line up the license plate bracket
under the top of the front bumper with
the tabs
B. Hold the license plate bracket
in place.
3) Mark the center of the holes
Cwith a
felt-tip pen.
4) Carefully drill two pilot holes using a 10 mm (0.39 in) drill bit at the marked loca-
tions. (Be sure that the drill only goes
through the bumper fascia.)
5) Insert the grommets into the holes in the bumper fascia.
6) Install the license plate bracket with the provided screws.
7) Install the license plate on to the bracket with bolts that are no longer than 14 mm
(0.55 in).
NTI327
INSTALLING FRONT LICENSE PLATE
Technical information10-13

11 Index
A
ABS (Anti-lock Braking System).......2-8
Warninglight ................2-8
Active sound enhancement .........5-70
Operation .................5-70
Adaptive Front lighting System .......2-67
Aids.......................5-63 Forward emergency braking system . .5-63
Hill Start Assist (HSA) ..........5-96
Intelligent Parking Assist (IPA) ......5-71
Air bags ....................1-46
Front passenger air bag switch .....1-46
Overview ...................0-2
Repair and replacement .........1-56
Supplemental Restraint System .....1-38
Warninglight............1-56,2-12
Air cleaner filter ................8-13
Air conditioner ................4-43
Heater and air conditioner ........4-43
Refrigerantandlubricant ........10-6
Servicing ..................4-52
Specification label ............10-12
Air fresheners ..................7-4
Anti-theft alarm system ...........2-59
AppGarage.................4-100 Screen...................4-100
Settingsscreen..............4-101 Around View Monitor
............4-25
Moving object detection (MOD) ....4-38
Settings...................4-34
Audible reminders ..............2-14
Audio ......................4-53
Operation precautions ..........4-53
Settings...................4-82
Source bar .................4-66
System...................4-53
Automatic transmission ............8-7
Fluid (ATF) ..................8-7
Operation .................5-20
B
Battery......................8-9
Caution label ................8-9
Cold weather ................5-97
Jump-starting ...............6-10
Replacement - Intelligent Key ......8-20
Saver system ................2-87
Vehicle battery ..............8-10
Blind Spot Warning (BSW) system .....5-36
Bluetooth®..................4-85 Hands-Free Phone System. . .4-85, 4-132
Information ................4-98
Streaming audio .............4-131
Boosterseats.................1-35 Precautions.................1-35
Brakes .....................8-17 ABS(Anti-LockBrakingSystem).... 5-92
Adjustment .................8-17
Fluid......................8-7
F
orward emergency braking system . . .5-63
Parking brake ...............5-27
Precautions.................5-91
System ...................5-91
Warninglight ................2-9
Break-in schedule ..............5-85
Brightness...................2-70 Instrument panel ............. 2-70
C
Capacities and recommendations .....10-2
Coolant ...................10-2
Fuel..................... 10-2
Oil......................10-2
Refrigerant.................10-2
Cardholder..................2-80
Center multi-function control panel .....4-2
Changing ....................8-4
Engine coolant ...............8-4
Engine oil ...................8-5
Engine oil filter ...............8-6
Tires and wheels .............8-34