wheel INFINITI QX30 2018 Quick Reference Guide

2
Cockpit Overview
Cruise control switch
Vehicle information display and menu control switches
Combined turn signal/Low-High beam/wiper and washer switch
Shift paddles
Audio and Bluetooth® control switches
Instrument brightness control (behind steering wheel)

8
MANUAL SEAT ADJUSTMENTS (IF SO EQUIPPED)
Forward and backward adjustment:
Pull the lever
, located under the seat, up and hold it while sliding
the seat forward or backward and release it to lock the seat in the
preferred position. When returning the seatback to the upright position,
always be certain it is completely secured in the latched position.
Seat angle adjustment:
Turn the hand-wheel
forward or backward to adjust the angles so
that your thighs are lightly supported.
Seat lifter:
Repeatedly pull up or push down the adjusting lever
to adjust the
seat height to the desired position.
Seatback angle:
Relieve the pressure on the seatback and turn the hand-wheel

forward or backward to adjust the seatback angle.
Seat Adjustments
LUMBAR SUPPORT
Push each side of the adjusting switch
to adjust the seat lumbar area
until the desired position is achieved.
POWER SEAT ADJUSTMENTS (IF SO EQUIPPED)
Forward and backward adjustment:
Move the adjusting switch
, located on the door, forward or backward
to the desired position.
Reclining:
Move the adjusting switch
forward or backward to the desired position.
Seat lifter (if so equipped):
1.


Pull up or

push down the adjusting switch
to adjust the seat
height until the desired position is achieved.
2.


T

ilt up or down the adjusting switch
to adjust the front angle of
the seat until the desired position is achieved.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.

9
Head Restraint Adjustment
(if so equipped)
To raise the head restraint:
Pull the head restraint up.
To lower the head restraint:
Push and hold the lock knob
and push the head
restraint down.
To move the head restraint forward:
Pull the head restraint toward the front of the vehicle until
it engages in one of the detents.
To move the head restraint backward:
Press and hold the button
and push the head restraint
backward until it is in the desired position, then release
the button.
Make sure the head restraint is fully engaged in position
after any adjustment.
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
Lane Departure Warning (LDW)
(if so equipped)
LDW warns you if the vehicle is beginning to leave the traveling lane. If a front
wheel passes over a lane marking, LDW will warn you through a visual alert and
an intermittent vibration in the steering wheel for up to 1.5 seconds.
To enable or disable LDW:
Press the
or button on the steering wheel to select the DriveAssist
menu
in the vehicle information display.
Press the
or button on the steering wheel to select Lane Departure
Warning and press the OK button
on the steering wheel.
Press the OK button
on the steering wheel to change the selection to Off,
Adaptive or Standard
.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.

14
SYSTEM OPERATING TIPS
•

The in
terior of the vehicle should be as quiet as possible.


•
Speak
naturally. Speaking too fast, too slow, too soft, or too
loud makes voice recognition more difficult.


•
C
onfirm that the correct voice commands are being used.
Glance at the screen to see the currently available commands.
USING THE VOICE RECOGNITION SYSTEM


•
Pr
ess the
button on the steering wheel, and a list of
commands will appear on the screen.


•

A

fter the tone sounds, speak the command.


•

T

o skip the voice prompt and give the command immediately,
press the
button on the steering wheel to interrupt the
system. Speak the next command after the tone sounds.
•


T

o cancel the command, press and hold the
button on
the steering wheel.
Voice Recognition
Please see your Infiniti InTouch™ Owner’s Manual for important safety information,
system limitations, and additional operating and feature information.
Intelligent Park Assist (IPA)
(if so equipped)
The Intelligent Park Assist (IPA) is an electronic parking aid. On straight and
even roads, IPA can be used to park in parallel spaces and to reverse into
perpendicular spaces.
To park using IPA:
•


When the IP
A detects a parking space,
the parking symbol
will appear in the
vehicle information display. To park in that
space, stop the vehicle and shift into the
(R) Reverse position.
•


A

"Start Park Assist" message will appear in
the vehicle information display. Press the
OK button on the steering wheel to enable
the IPA, or press the
button to cancel
the operation.
•


R

elease the steering wheel and continue to control the accelerator,
brake and gear shift to maneuver into the parking space.
•


S

top as soon as the sonar function sounds the continuous warning tone,
if not before. A message will appear in the vehicle information display if
you need to change gears.
•


When the pr

ocedure is complete, a "ParkAssist switched off" message
will appear in the vehicle information display. Shift into the (P) Park
position, and apply the electric parking brake to secure the vehicle.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.