check engine INFINITI QX4 2001 Factory Service Manual

SEF243Y
SEF175Y
PROCEDURE FOR MALFUNCTION DNBEC0054S04CAUTION:
Always drive vehicle at a safe speed.
With CONSULT-IINBEC0054S04021) Turn ignition switch ªONº.
2) Start engine and warm it up to normal operating temperature.
If engine cannot be started, go to ªDiagnostic Procedureº,
EC-155.
3) Select ªDATA MONITORº mode with CONSULT-II.
4) Check the voltage of MAS AIR/FL SE with ªDATA MONITORº.
5) Increases engine speed to about 4,000 rpm.
6) Monitor the linear voltage rise in response to engine speed
increases.
If NG, go to ªDiagnostic Procedureº, EC-155.
If OK, go to following step.
7) Maintain the following conditions for at least 10 consecutive
seconds.
ENG SPEED More than 2,000 rpm
THRTL POS SEN More than 3V
Selector lever Suitable position
Driving location Driving vehicle uphill (Increased engine load)
will help maintain the driving conditions
required for this test.
8) If 1st trip DTC is detected, go to ªDiagnostic Procedureº,
EC-155.
SEF534P
Overall Function CheckNBEC0055PROCEDURE FOR MALFUNCTION DNBEC0055S01Use this procedure to check the overall function of the mass air flow
sensor circuit. During this check, a 1st trip DTC might not be con-
firmed.
With GSTNBEC0055S01011) Start engine and warm it up to normal operating temperature.
2) Select ªMODE 1º with GST.
3) Check the mass air flow sensor signal with ªMODE 1º.
4) Check for linear mass air flow sensor signal value rise in
response to increases to about 4,000 rpm in engine speed.
5) If NG, go to ªDiagnostic Procedureº, EC-155.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0100 MASS AIR FLOW SENSOR (MAFS)
DTC Confirmation Procedure (Cont'd)
EC-153

Diagnostic ProcedureNBEC0057
1 INSPECTION START
Which malfunction (A, B, C, D or E) is duplicated?
MTBL0373
Type I or Type II
Type I©GO TO 3.
Type II©GO TO 2.
2 CHECK INTAKE SYSTEM
Check the following for connection.
IAir duct
IVacuum hoses
IIntake air passage between air duct to intake manifold collector
OK or NG
OK©GO TO 3.
NG©Reconnect the parts.
3 RETIGHTEN GROUND SCREWS
1. Turn ignition switch ªOFFº.
2. Loosen and retighten engine ground screws.
SEF959Y
©GO TO 4.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0100 MASS AIR FLOW SENSOR (MAFS)
Diagnostic Procedure
EC-155

7 CHECK MAFS INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check harness continuity between MAFS terminal 1 and ECM terminal 61.
Refer to Wiring Diagram.
Continuity should exist.
2. Also check harness for short to ground and short to power.
OK or NG
OK©GO TO 8.
NG©Repair open circuit or short to ground or short to power in harness or connectors.
8 CHECK MASS AIR FLOW SENSOR
1. Reconnect harness connectors disconnected.
2. Start engine and warm it up to normal operating temperature.
3. Check voltage between ECM terminal 61 (Mass air flow sensor signal) and ground.
SEF298X
4. If the voltage is out of specification, disconnect MAFS harness connector and connect it again.
Then repeat above check.
OK or NG
OK©GO TO 9.
NG©Replace mass air flow sensor.
9 CHECK INTERMITTENT INCIDENT
Refer to ªTROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTº, EC-140.
©INSPECTION END
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0100 MASS AIR FLOW SENSOR (MAFS)
Diagnostic Procedure (Cont'd)
EC-157

Diagnostic ProcedureNBEC0731
1 RETIGHTEN GROUND SCREWS
1. Turn ignition switch ªOFFº.
2. Loosen and retighten engine ground screws.
SEF959Y
©GO TO 2.
2 CHECK ABSOLUTE PRESSURE SENSOR CONNECTOR FOR WATER
1. Disconnect absolute pressure sensor harness connector.
SEF961Y
2. Check sensor harness connector for water.
Water should not exist.
OK or NG
OK©GO TO 3.
NG©Repair or replace harness connector.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0105 ABSOLUTE PRESSURE SENSOR
Diagnostic Procedure
EC-161

3 CHECK ABSOLUTE PRESSURE SENSOR POWER SUPPLY CIRCUIT
1. Turn ignition switch ªONº.
2. Check voltage between absolute pressure sensor terminal 1 and ground with CONSULT-II or tester.
SEF299X
OK or NG
OK©GO TO 4.
NG©Repair harness or connectors.
4 CHECK ABSOLUTE PRESSURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch ªOFFº.
2. Check harness continuity between absolute pressure sensor terminal 3 and engine ground.
Refer to Wiring Diagram.
Continuity should exist.
3. Also check harness for short to ground and short to power.
OK or NG
OK©GO TO 6.
NG©GO TO 5.
5 DETECT MALFUNCTIONING PART
Check the following.
IHarness for open or short between ECM and absolute pressure sensor
IHarness for open or short between TCM (Transmission Control Module) and absolute pressure sensor
©Repair open circuit or short to ground or short to power in harness or connectors.
6 CHECK ABSOLUTE PRESSURE SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect ECM harness connector.
2. Check harness continuity between ECM terminal 80 and absolute pressure sensor terminal 2.
Continuity should exist.
3. Also check harness for short to ground and short to power.
OK or NG
OK©GO TO 7.
NG©Repair open circuit or short to ground or short to power in harness or connectors.
DTC P0105 ABSOLUTE PRESSURE SENSOR
Diagnostic Procedure (Cont'd)
EC-162

7 CHECK ABSOLUTE PRESSURE SENSOR
1. Remove absolute pressure sensor with its harness connector connected.
2. Remove hose from absolute pressure sensor.
3. Install a vacuum pump to absolute pressure sensor.
4. Turn ignition switch ªONº and check output voltage between ECM terminal 80 and engine ground under the following
conditions.
SEF300XA
CAUTION:
IAlways calibrate the vacuum pump gauge when using it.
IDo not apply below þ93.3 kPa (±700 mmHg, ±27.56 inHg) or over 101.3 kPa (760 mmHg, 29.92 inHg) of pressure.
OK or NG
OK©GO TO 8.
NG©Replace absolute pressure sensor.
8 CHECK INTERMITTENT INCIDENT
Refer to ªTROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTº, EC-140.
©INSPECTION END
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0105 ABSOLUTE PRESSURE SENSOR
Diagnostic Procedure (Cont'd)
EC-163

SEF058Y
PROCEDURE FOR MALFUNCTION ANBEC0066S01With CONSULT-IINBEC0066S01011) Turn ignition switch ªONº.
2) Select ªDATA MONITORº mode with CONSULT-II.
3) Wait at least 5 seconds.
4) If 1st trip DTC is detected, go to ªDiagnostic Procedureº,
EC-167.
With GSTNBEC0066S0102Follow the procedure ªWith CONSULT-IIº above.
SEF176Y
PROCEDURE FOR MALFUNCTION BNBEC0066S02CAUTION:
Always drive vehicle at a safe speed.
TESTING CONDITION:
This test may be conducted with the drive wheels lifted in the
shop or by driving the vehicle. If a road test is expected to be
easier, it is unnecessary to lift the vehicle.
With CONSULT-IINBEC0066S02011) Wait until engine coolant temperature is less than 90ÉC
(194ÉF).
a) Turn ignition switch ªONº.
b) Select ªDATA MONITORº mode with CONSULT-II.
c) Check the engine coolant temperature.
d) If the engine coolant temperature is not less than 90ÉC
(194ÉF), turn ignition switch ªOFFº and cool down engine.
IPerform the following steps before engine coolant temperature
is above 90ÉC (194ÉF).
2) Turn ignition switch ªONº.
3) Select ªDATA MONITORº mode with CONSULT-II.
4) Start engine.
5) Hold vehicle speed at more than 70 km/h (43 MPH) for 100
consecutive seconds.
6) If 1st trip DTC is detected, go to ªDiagnostic Procedureº,
EC-167.
With GSTNBEC0066S0202Follow the procedure ªWith CONSULT-IIº above.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0110 INTAKE AIR TEMPERATURE SENSOR
DTC Confirmation Procedure (Cont'd)
EC-165

Diagnostic ProcedureNBEC0068
1 CHECK INTAKE AIR TEMPERATURE SENSOR POWER SUPPLY CIRCUIT
1. Turn ignition switch ªOFFº.
2. Disconnect intake air temperature sensor harness connector.
SEF962Y
3. Turn ignition switch ªONº.
4. Check voltage between terminal 1 and ground.
SEF301X
OK or NG
OK©GO TO 3.
NG©GO TO 2.
2 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors E1, M1
IHarness connectors M33, F22
IHarness for open or short between ECM and intake air temperature sensor
©Repair harness or connectors.
3 CHECK INTAKE AIR TEMPERATURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch ªOFFº.
2. Check harness continuity between sensor terminal 2 and engine ground.
Refer to Wiring Diagram.
Continuity should exist.
3. Also check harness for short to power.
OK or NG
OK©GO TO 5.
NG©GO TO 4.
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0110 INTAKE AIR TEMPERATURE SENSOR
Diagnostic Procedure
EC-167

Diagnostic ProcedureNBEC0073
1 CHECK ECTS POWER SUPPLY CIRCUIT
1. Turn ignition switch ªOFFº.
2. Disconnect engine coolant temperature sensor (ECTS) harness connector F112, F28.
SEF370Z
3. Turn ignition switch ªONº.
4. Check voltage between ECTS harness connector F28 terminal 3 and ground with CONSULT-II or tester.
SEF371Z
OK or NG
OK©GO TO 3.
NG©GO TO 2.
2 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors F112, F28
IHarness for open or short between ECM and engine coolant temperature sensor
©Repair harness or connectors.
3 CHECK ECTS GROUND CIRCUIT FOR OPEN AND CIRCUIT
1. Turn ignition switch ªOFFº.
2. Check harness continuity between ECTS terminal 2 and engine ground.
Refer to Wiring Diagram.
Continuity should exist.
3. Also check harness for short to power.
OK or NG
OK©GO TO 5.
NG©GO TO 4.
DTC P0115 ENGINE COOLANT TEMPERATURE SENSOR (ECTS) (CIRCUIT)
Diagnostic Procedure
EC-172

4 DETECT MALFUNCTIONING PART
Check the following.
IHarness connectors F112, F28
IHarness for open between ECM and engine coolant temperature sensor
IHarness for open between TCM (Transmission Control Module) and engine coolant temperature sensor
©Repair open circuit or short to power in harness or connectors.
5 CHECK ENGINE COOLANT TEMPERATURE SENSOR
Check resistance between engine coolant temperature sensor terminals 1 and 2 as shown in the figure.
SEF304X
OK or NG
OK©GO TO 6.
NG©Replace engine coolant temperature sensor.
6 CHECK INTERMITTENT INCIDENT
Refer to ªTROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTº, EC-140.
©INSPECTION END
GI
MA
EM
LC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0115 ENGINE COOLANT TEMPERATURE SENSOR (ECTS) (CIRCUIT)
Diagnostic Procedure (Cont'd)
EC-173