display INFINITI QX4 2005 Factory Service Manual

AV-76
NAVIGATION SYSTEM
Revision: October 20052005 QX56
TIRE PRESSURE

Pressure indication in psi on the screen indicates that the
pressure is being measured. After a few trips, the pressures for
all four tires will be displayed.

The order of tire pressure figures displayed on the screen does
not correspond with the actual order of tire position.

Tire pressure rises and falls depending on the heat caused by
the vehicle's traveling condition and the temperature.

In case of low tire pressure, the low tire pressure warning light
will come on and/or a warning is displayed on the screen.

FLAT TIRE – very low tire pressure.
NOTE:

In a case of FLAT TIRE pressure, interrupt screen is not shown on the display.

On the screen of TIRE PRESSURE, "FLAT TIRE Check All tires" is displayed.
WARNING INDICATIONS
Warning signal is received from BCM through CAN communication
line.
CAN Communication System DescriptionEKS00BJE
Refer to LAN-5, "CAN COMMUNICATION" .
WKIA1809E
WKIA1957E
Warning indicatorsWarning lamps in
instrument panelWarning detection and cancel conditions Cases of malfunction
DOOR OPEN DoorDetection conditionVehicle is running [approx. 5 km/h
(3 MPH) or faster] and door ajar of
any of the doors is detected.
Door is open
Cancel conditionVehicle is stopped and all the
doors lock.
LIFTGATE OPEN DoorDetection conditionVehicle is running [approx. 5 km/h
(3 MPH) or faster] and liftgate ajar
and/or glass hatch ajar is detected.Liftgate and/or glass
hatch is open
Cancel conditionVehicle is stopped and both liftgate
and glass hatch lock.

AV-90
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Terminals and Reference Value for NAVI Control unitEKS00BJK
Te r m i n a l N o .
(Wire color)
ItemSignal
input/
outputCondition
Vo l ta g e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
1 (B) Ground Ground – ON – 0 V –
2 (Y)
GroundBattery
powerInput OFF – Battery voltageSystem does not
work properly.
3 (Y)
4 (B) Ground Ground – ON – 0 V –
6 (O) Ground ACC signal Input ACC – Battery voltageSystem does not
work properly.
7 (B) 8 (W)Voice guide
signalOutput ONPress the “GUIDE/
VOICE” button.Only route guide
and operation
guide are not
heard.
9–Shield
ground–– – –Audio noise
interference.
14 –Shield
ground–– – –Video display
interference.
15 (B) 17RGB signal
(B: blue)Output ONSelect “Display
Diagnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks yellowish.
16 (BR) 14RGB syn-
chronizing
signalOutput ONPress the “MAP”
button.NAVI screen is
rolling.
17 –Shield
ground–– – –Video display
interference.
18 (R) 17RGB signal
(R: red)Output ONSelect “Display
Diagnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks bluish.
21 (R/W) 17RGB signal
(G: green)Output ONSelect “Display
Diagnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks reddish.
SKIA0171J
SKIA4979E
SKIA0164E
SKIA4977E
SKIA4978E

NAVIGATION SYSTEM
AV-91
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
25 (R/L) 30 (B)Illumination
signalInput ONLighting switch in
1st positionBattery voltageDisplay unit illu-
mination does
not change
when lighting
switch is turned
to 1st position.- Lighting switch is
OFF3V or less
26 (G/R) Ground Ignition signal Input ON – Battery voltageNavigation cur-
rent location
mark does not
indicate the cor-
rect position.
27 (G/W) GroundReverse
signalInput ONSelector lever in R
positionBattery voltageThe navigation
current location
mark moves
strangely when
the vehicle is
moving back-
wards. Selector lever not in
R position0V
28 (W/R) GroundVehicle
speed signal
(8-pulse)Input ONWhen vehicle speed
is approx. 40 km/h
(25 MPH)Navigation cur-
rent location
mark does not
indicate the cor-
rect position.
43 –Shield
ground–– – – –
44 (L) GroundCommunica-
tion signal (+)Input/
outputON –System does not
work properly.
45 (P) GroundCommunica-
tion signal (–)Input/
outputON –System does not
work properly.
66 67 GPS signal Input ONConnector is not
connected.5 VNavigation sys-
tem GPS correc-
tion is not
possible. Te r m i n a l N o .
(Wire color)
ItemSignal
input/
outputCondition
Vo l ta g e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
PKIA1935E
SKIA0175E
SKIA0176E

AV-92
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Terminals and Reference Value for Display Control unitEKS00BJL
Terminal No.
(Wire color)
ItemSignal
input/
outputCondition
Voltage
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
1 (Y) GroundBattery
PowerInput OFF – Battery voltageSystem does not
work properly.
2 (L/W) GroundPower Sup-
ply (Inverter) Output ON – 9 VScreen is not
shown.
3 (B) Ground Ground – ON – 0 V –
4 (L/R) GroundPower Sup-
ply (Signal) Output ON – 9 VScreen is not
shown.
5 (P) Ground(Inverter)
Ground –ON – 0 V –
6 (GR) GroundReverse
signalInput ONSelector lever in R
positionBattery voltage
Impossible to
gain direction of
vehicle. Selector lever not in
R position0 V
7 (P/L) Ground(Signal)
Ground –ON – 0 V –
10 (O) Ground ACC signal Input ACC – Battery voltageSystem does not
work properly.
12 (G/R) Ground Ignition signal Input ON – Battery voltageVehicle informa-
tion setting is not
possible.
13 (B) Ground Ground – ON – 0 V –
14 (R/L) GroundIllumination
signalInput OFFLighting switch posi-
tion 1st or 2ndBattery voltageDisplay unit
does not change
when lighting
switch is turned
to 1st position. Lighting switch posi-
tion OFF0 V
16 (W/R) GroundVehicle
speed signal
(8–pulse)Input ONWhen vehicle speed
is approx. 40 km/h
(25 MPH)Value of vehicle
speed informa-
tion is not accu-
rately displayed.
25 (L) – CAN-H – – – – –
26 (P) – CAN-L – – – – –
28 (V) GroundCommunica-
tion signal (+)Input/
OutputON –System does not
work properly.
29 –Shield
ground–– – – –
SKIA0168E
SKIA0175E

NAVIGATION SYSTEM
AV-93
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
30 (LG) GroundCommunica-
tion signal (–)Input/
outputON –System does not
work properly.
32 (L) GroundCommunica-
tion signal (+)Input/
outputON –System does not
work properly.
33 –Shield
ground–– – – –
34 (P) GroundCommunica-
tion signal (–)Input/
outputON –System does not
work properly.
36 (B/W) 37Display Com-
munication
signal
(DCU-DSP)Output ONPress the “TRIP”
button.Though a screen
is displayed, it is
impossible to
adjust bright-
ness.
37 –Shield
ground–– – – –
38 (L) 37Display Com-
munication
signal
(DSP-DCU)Input ONPress the “TRIP”
button.Though a screen
is displayed, it is
impossible to
adjust bright-
ness.
39 –Shield
ground–– – – –
40 (O/L) GroundAudio TX
Communica-
tion signalOutput ONOperate audio
volume.Audio does not
operate properly. Terminal No.
(Wire color)
ItemSignal
input/
outputCondition
Vo ltag e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
SKIA0176E
SKIA0175E
SKIA0176E
SKIA4364E
SKIA4363E
SKIA4402E

AV-94
NAVIGATION SYSTEM
Revision: October 20052005 QX56
41 –Shield
ground–– – – –
42 (W/L) GroundAudio RX
communica-
tion signalInput ONOperate audio
volume.Audio does not
operate properly.
43 (W) 41RGB syn-
chronizing
signalInput ONPress the “MAP”
button.NAVI screen is
rolling.
44 (R/L) 45RGB signal
(R: red)Input ONSelect “Display
Diagnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks bluish.
45 –Shield
ground–– – – –
46 (R/W) 45RGB signal
(G: green)Input ONSelect “Display
Diagnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks reddish.
47 –Shield
ground–– – – –
48 (B) 45RGB signal
(B: blue)Input ONSelect “Display
Diagnosis (NAVI)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks yellowish.
49 –Shield
ground–– – – –
50 (R/L) 47RGB signal
(R: red)Output ONSelect “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.NAVI screen
looks bluish. Terminal No.
(Wire color)
ItemSignal
input/
outputCondition
Voltage
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
SKIA4403E
SKIA0164E
SKIA4977E
SKIA4978E
SKIA4979E
SKIA4980E

NAVIGATION SYSTEM
AV-95
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
51 (B) 49RGB area
(YS) signalOutput ONPress the“TRIP”
button.RGB screen is
not shown.
52 (R/W) 47RGB signal
(G: green)Output ONSelect “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.Screen looks
reddish.
53 (W) 49Vertical syn-
chronizing
(VP) signalInput ON –Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
54 (B) 47RGB signal
(B: blue)Output ONSelect “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.Screen looks
yellowish.
55 (R) 49Horizontal
synchroniz-
ing (HP) sig-
nalInput ON –Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
56 (G) 49RGB syn-
chronizing
signalOutput ONPress the “TRIP”
button.NAVI screen is
rolling. Terminal No.
(Wire color)
ItemSignal
input/
outputCondition
Vo ltag e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
SKIA0162E
SKIA4981E
SKIA4983E
SKIA4982E
SKIA4983E
SKIA0164E

AV-96
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Terminals and Reference Value for Display unitEKS00BJM
Terminal No. (Wire
color)
ItemSignal
input/
outputCondition
Vo ltag e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
1 (B) Ground Ground – ON – 0 V –
2 (L/W) GroundPower sup-
ply (Inverter) Input ON – 9 VScreen is not
shown.
3 (L/R) GroundPower sup-
ply (Signal) Input ON – 9 VScreen is not
shown.
6 (R/W) 7RGB signal
(G: green)Input ONSelect “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.Screen looks
reddish.
7–Shield
ground–– – – –
8 (R) 21Horizontal
synchroniz-
ing (HP) sig-
nalOutput ON –Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
9 (B) 21RGB area
(YS) signalInput ONPress the “TRIP”
button.RGB screen is
not shown.
11 (B/W) 23Display com-
munication
signal
(DCU-DSP)Input ON –Though a screen
is displayed, it is
impossible to
adjust bright-
ness.
13 (P) Ground(Inverter)
Ground –ON – 0 V –
14 (P/L) Ground(Signal)
Ground –ON – 0 V –
17 (R/L) 7RGB signal
(R: red)Input ONSelect “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.Screen looks
bluish.
SKIA4981E
SKIA4983E
SKIA0162E
SKIA4364E
SKIA4980E

NAVIGATION SYSTEM
AV-97
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
18 (B) 7RGB signal
(B: blue)Input ONSelect “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.Screen looks
yellowish.
19 (G) 21RGB syn-
chronizing
signalInput ONPress the “TRIP”
button.NAVI screen is
rolling.
20 (W) 21Vertical syn-
chronizing
(VP) signalOutput ON –Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
21 –Shield
ground–– – – –
22 (L) 23Display com-
munication
signal
(DSP-DCU)Output ON –Though a screen
is displayed, it is
impossible to
adjust bright-
ness.
23 –Shield
ground–– – – – Terminal No. (Wire
color)
ItemSignal
input/
outputCondition
Vo l ta g e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
SKIA4982E
SKIA0164E
SKIA4983E
SKIA4363E

NAVIGATION SYSTEM
AV-101
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
On Board Self-Diagnosis FunctionEKS00BJP
DESCRIPTION

Diagnosis function consists of the self-diagnosis mode performed automatically and the CONFIRMATION/
ADJUSTMENT mode operated manually.

Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.

CONFIRMATION/ADJUSTMENT mode is used to perform trouble diagnosis that require operation and
judgment by an operator (trouble that cannot be automatically judged by the system), to check/change the
set value, and to display the History of Errors of the navigation system.
DIAGNOSIS ITEM
NOTE:
Make the status that is set by D/N function be shown.
Self-Diagnosis Mode (DCU)EKS00BJQ
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
Mode Description
Self-diagnosis (DCU) Display control unit diagnosis.
Self-diagnosis (NAVI)

NAVI Control unit diagnosis (DVD-ROM drive) will not be diagnosed
when no map DVD-ROM is in it.

Analyzes connection between the NAVI control unit and the GPS
antenna and operation of each unit.
CONFIRMATION/
ADJUSTMENTDisplay diagnosisIn display control unit mode, color tone and shading of the screen can be
checked by the display of a color bar and a gray scale.
Vehicle signalsIn display control unit mode, analyzes the following vehicle signals: Vehi-
cle speed signal, light signal
NOTE , ignition switch signal, and reverse sig-
nal.
Auto Climate Control A/C self-diagnosis of A/C system.
NavigationDisplay diagnosisIn NAVI C/U mode, color tone and shading of the screen can be checked
by the display of a color bar and a gray scale.
Vehicle signalsIn NAVI C/U mode, analyzes the following vehicle signals: Vehicle speed
signal, light signal, ignition switch signal, and reverse signal.
History of ErrorsDiagnosis results previously stored in the memory (before turning ignition
switch ON) are displayed in this mode. Time and location when/where the
errors occurred are also displayed.
Naviga-
tionDisplay Lon-
gitude & Lat-
itudeDisplay the map. Use the joystick to adjust position. Longitude and latitude
will be displayed.
Speed Cali-
brationUnder ordinary conditions, the navigation system distance measuring
function will automatically compensate for minute decreases in wheel and
tire diameter caused by tire wear or low-pressure. Speed calibration imme-
diately restores system accuracy in cases such as when distance calibra-
tion is needed because of the use of tire chains in inclement weather.
Angle
adjustmentCorrects difference between actual turning angle of a vehicle and turning
angle of the car mark on the display.
Initialize
LocationThis mode is for initializing the current location. Use when the vehicle is
transported a long distance on a trailer, etc.
CAN DIAG SUPPORT MONITOR Display status of CAN communication.