display INFINITI QX4 2005 Factory Service Manual

REAR VIEW MONITOR
DI-79
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: October 20052005 QX56
4. Select “WORK SUPPORT”, “DATA MONITOR” or “ECU PART
NUMBER”.
WORK SUPPORT
Operation Procedure
1. Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
2. Touch either “SELCT GUIDELINE PATTERN” or “ADJ GUIDELINE POSITION” on the “SELECT WORK
ITEM” screen.
Refer to DI-80, "
SIDE DISTANCE GUIDELINE CORRECTION PROCEDURE" for detail.
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on the “SELECT MONITOR ITEM” screen.
3. When “SELECTION FROM MENU” is selected, touch individual items to be monitored. When “ALL SIG-
NALS” is selected, all items will be monitored.
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
Display Item List
BCIA0031E
SELCT GUIDELINE PATTERN Side distance guideline is optional from two patterns.
ADJ GUIDELINE POSITION Side distance guideline is adjustable toward up and down, right and left.
ALL SIGNALS Monitors all signals.
SELECTION FROM MENU Selects and monitors individual signal.
Display item [Unit]ALL SIG-
NALSSELECTION
FROM MENUContents
R POSI SIG [ON/OFF] X X Indicates [ON/OFF] condition of R position signal input.

REAR VIEW MONITOR
DI-83
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: October 20052005 QX56
Rear View Is Not Displayed With The A/T Selector Lever In R PositionEKS00BDN
1. BACK-UP LAMP INSPECTION
1. Turn ignition switch ON.
2. Shift A/T selector lever to R position.
Does back-up lamp illuminate?
YES >> GO TO 2.
NO >> Check back-up lamp system. Refer to LT-106, "
BACK-UP LAMP" .
2. CHECK REVERSE POSITION INPUT SIGNAL
With CONSULT-II
Select “DATA MONITOR” of “REARVIEW CAMERA”. Operate igni-
tion switch with “R POSI SIG” of “DATA MONITOR” and check oper-
ate status.
Without CONSULT-II
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector.
3. Turn ignition switch ON.
4. Shift A/T selector lever to R position.
5. Check voltage between rear view camera control unit harness
connector B73 terminal 4 (G/W) and ground.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open or short between rear view
camera control unit and back-up lamp relay.
3. CHECK DISPLAY CONTROL UNIT OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector.
3. Turn ignition switch ON.
4. Check voltage between rear view camera control unit harness
connector B73 terminal 5 (BR) and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
SKIA7147E
Battery voltage should exist.
SKIA5086E
Voltage : Approx. 5V
SKIA7148E

DI-84
REAR VIEW MONITOR
Revision: October 20052005 QX56
4. CHECK DISPLAY CONTROL UNIT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display control unit connector.
3. Check continuity between rear view camera control unit harness
connector B73 terminal 5 (BR) and display control unit harness
connector M94 terminal 8 (BR).
4. Check continuity between rear view camera control unit harness
connector B73 terminal 5 (BR) and ground.
OK or NG
OK >> Replace display control unit. Refer to AV- 1 5 8 , "Removal and Installation of Display Control Unit" .
NG >> Repair harness or connector.
5. CHECK AV CONTROL SIGNAL
1. Turn ignition switch OFF.
2. Connect rear view camera control unit connector.
3. Shift A/T selector lever to R position.
4. Check voltage between rear view camera control unit harness
connector B73 terminal 5 (BR) and ground.
OK or NG
OK >> GO TO 6.
NG >> Replace rear view camera control unit. Refer to DI-87,
"Removal and Installation of Rear View Camera Control
Unit" .
6. CHECK REAR VIEW CAMERA OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera connector.
3. Check continuity between rear view camera control unit harness
connector B73 terminal 8 (Y) and rear view camera harness
connector D504 terminal 1 (Y).
4. Check continuity between rear view camera control unit harness
connector B73 terminal 9 and rear view camera harness con-
nector D504 terminal 4.
5. Check continuity between rear view camera control unit harness connector B73 terminal 10 (G) and rear
view camera harness connector D504 terminal 3 (G).
OK or NG
OK >> GO TO 7.
NG >> Repair harness or connector.Continuity should exist.
Continuity should not exist.
SKIA7149E
Voltage : Approx. 0V
SKIA7150E
Continuity should exist.
Continuity should exist.
Continuity should exist.
SKIA5095E

DI-86
REAR VIEW MONITOR
Revision: October 20052005 QX56
10. CHECK REAR VIEW CAMERA SIGNAL
1. Connect rear view camera connector.
2. Turn ignition switch ON.
3. Shift A/T selector lever to R position.
4. Check voltage signal between rear view camera control unit har-
ness connector B73 terminal 10 (G) and ground.
OK or NG
OK >> GO TO 11.
NG >> Replace the rear view camera. Refer to DI-87, "
Removal and Installation of Rear View Camera" .
11 . CHECK COMPOSITE SIGNAL OPEN OR SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector and display
unit connector.
3. Check continuity between rear view camera control unit harness
connector B73 terminal 12 (W) and display unit harness connec-
tor M93 terminal 15 (W).
4. Check continuity between rear view camera control unit harness
connector B73 terminal 12 (W) and ground.
OK or NG
OK >> GO TO 12.
NG >> Repair harness or connector.
12. CHECK COMPOSITE SIGNAL GROUND CIRCUIT
1. Check continuity between rear view camera control unit harness
connector B73 terminal 11 and display unit harness connector
M93 terminal 4.
2. Check continuity between rear view camera control unit harness
connector B73 terminal 11 and ground.
OK or NG
OK >> GO TO 13.
NG >> Repair harness or connector.10 (G) - Ground:
SKIA5100E
SKIA4894E
Continuity should exist.
Continuity should not exist.
WKIA1825E
Continuity should exist.
Continuity should not exist.
WKIA1826E

REAR VIEW MONITOR
DI-87
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: October 20052005 QX56
13. CHECK REAR VIEW CAMERA CONTROL UNIT COMPOSITE SIGNAL
1. Connect rear view camera control unit connector and display
unit connector.
2. Turn ignition switch ON.
3. Check voltage signal between rear view camera control unit har-
ness connector B73 terminal 12 (W) and ground.
OK or NG
OK >> Replace the display unit. Refer to AV-158, "Removal and Installation of Display Unit" .
NG >> Replace the rear view camera control unit. Refer to DI-87, "
Removal and Installation of Rear View
Camera Control Unit" .
Removal and Installation of Rear View Camera Control UnitEKS00BDO
REMOVAL
1. Remove luggage side finishers LH. Refer to EI-40, "LUGGAGE
FLOOR TRIM" .
2. Remove screws (2) and remove rear view camera control unit.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation of Rear View CameraEKS00BDP
REMOVAL
1. Remove back door lower finisher. Refer to EI-42, "BACK DOOR TRIM" .
2. Remove connector.
3. Remove screws (2) and remove rear view camera.
INSTALLATION
Installation is in the reverse order of removal.12 (W) - Ground:
WKIA1827E
SKIA4896E
LKIA0478E
LKIA0479E

EC-8Revision: October 2005
INDEX FOR DTC
2005 QX56
INDEX FOR DTCPFP:00024
DTC No. IndexUBS00KYY
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-163, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3
U1000
1000*4CAN COMM CIRCUITEC-163
U1001
1001*4CAN COMM CIRCUITEC-163
P0000 0000NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.—
P0037 0037 HO2S2 HTR (B1)EC-166
P0038 0038 HO2S2 HTR (B1)EC-166
P0057 0057 HO2S2 HTR (B2)EC-166
P0058 0058 HO2S2 HTR (B2)EC-166
P0101 0101 MAF SEN/CIRCUITEC-174
P0102 0102 MAF SEN/CIRCUITEC-183
P0103 0103 MAF SEN/CIRCUITEC-183
P0112 0112 IAT SEN/CIRCUITEC-191
P0113 0113 IAT SEN/CIRCUITEC-191
P0117 0117 ECT SEN/CIRCUITEC-195
P0118 0118 ECT SEN/CIRCUITEC-195
P0122 0122 TP SEN 2/CIRCEC-201
P0123 0123 TP SEN 2/CIRCEC-201
P0125 0125 ECT SENSOREC-208
P0127 0127 IAT SENSOREC-211
P0128 0128 THERMSTAT FNCTNEC-214
P0138 0138 HO2S2 (B1)EC-216
P0139 0139 HO2S2 (B1)EC-225
P0158 0158 HO2S2 (B2)EC-216
P0159 0159 HO2S2 (B2)EC-225
P0171 0171 FUEL SYS-LEAN-B1EC-236
P0172 0172 FUEL SYS-RICH-B1EC-245
P0174 0174 FUEL SYS-LEAN-B2EC-236
P0175 0175 FUEL SYS-RICH-B2EC-245
P0181 0181 FTT SENSOREC-253
P0182 0182 FTT SEN/CIRCUITEC-259
P0183 0183 FTT SEN/CIRCUITEC-259
P0222 0222 TP SEN 1/CIRCEC-264
P0223 0223 TP SEN 1/CIRCEC-264
P0300 0300 MULTI CYL MISFIREEC-271
P0301 0301 CYL 1 MISFIREEC-271
P0302 0302 CYL 2 MISFIREEC-271
P0303 0303 CYL 3 MISFIREEC-271

EC-12Revision: October 2005
INDEX FOR DTC
2005 QX56
Alphabetical IndexUBS00KYZ
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-163, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
Items
(CONSULT-II screen terms)DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SENSOR1 (B1) P1271 1271EC-459
A/F SENSOR1 (B1) P1272 1272EC-468
A/F SENSOR1 (B1) P1273 1273EC-477
A/F SENSOR1 (B1) P1274 1274EC-487
A/F SENSOR1 (B1) P1276 1276EC-497
A/F SENSOR1 (B1) P1278 1278EC-507
A/F SENSOR1 (B1) P1279 1279EC-519
A/F SENSOR1 (B2) P1281 1281EC-459
A/F SENSOR1 (B2) P1282 1282EC-468
A/F SENSOR1 (B2) P1283 1283EC-477
A/F SENSOR1 (B2) P1284 1284EC-487
A/F SENSOR1 (B2) P1286 1286EC-497
A/F SENSOR1 (B2) P1288 1288EC-507
A/F SENSOR1 (B2) P1289 1289EC-519
A/F SEN1 HTR (B1) P1031 1031EC-386
A/F SEN1 HTR (B1) P1032 1032EC-386
A/F SEN1 HTR (B2) P1051 1051EC-386
A/F SEN1 HTR (B2) P1052 1052EC-386
A/T INTERLOCK P1730 1730AT- 1 3 5
A/T TCC S/V FNCTN P0744 0744AT-11 7
ACC COMMAND VALUE*7P1568 1568EC-559
APP SEN 1/CIRC P2122 2122EC-591
APP SEN 1/CIRC P2123 2123EC-591
APP SEN 2/CIRC P2127 2127EC-597
APP SEN 2/CIRC P2128 2128EC-597
APP SENSOR P2138 2138EC-611
ASCD BRAKE SW P1572 1572EC-560 (Models with ICC)
EC-569
(Models with ASCD)
ASCD SW P1564 1564EC-545
(Models with ICC)
EC-552
(Models with ASCD)
ASCD VHL SPD SEN*
6P1574 1574EC-577 (Models with ICC)
EC-579
(Models with ASCD)
ATF TEMP SEN/CIRC P0710 0710AT- 1 2 6
BRAKE SW/CIRCUIT P1805 1805EC-586
CAN COMM CIRCUIT U1000
1000*4EC-163
CAN COMM CIRCUIT U1001
1001*4EC-163
CKP SEN/CIRCUIT P0335 0335EC-284
C L O S E D L O O P - B 1 P 11 4 8 11 4 8EC-437
C L O S E D L O O P - B 2 P 11 6 8 11 6 8EC-437

EC-18Revision: October 2005
PRECAUTIONS
2005 QX56

After performing each TROUBLE DIAGNOSIS, perform DTC
Confirmation Procedure or Overall Function Check.
The DTC should not be displayed in the DTC Confirmation
Procedure if the repair is completed. The Overall Function
Check should be a good result if the repair is completed.

When measuring ECM signals with a circuit tester, never
allow the two tester probes to contact.
Accidental contact of probes will cause a short circuit and
damage the ECM power transistor.

Do not use ECM ground terminals when measuring input/
output voltage. Doing so may result in damage to the ECM's
transistor. Use a ground other than ECM terminals, such as
the ground.

B1 indicates the bank 1, B2 indicates the bank 2 as shown
in the figure.
SEF 2 17 U
SEF 3 48 N
PBIB11 44 E

EVAPORATIVE EMISSION SYSTEM
EC-37
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: October 20052005 QX56
How to Detect Fuel Vapor LeakageUBS00KZI
CAUTION:

Never use compressed air or a high pressure pump.

Do not exceed 4.12 kPa (0.042 kg/cm2 , 0.6 psi) of pressure in EVAP system.
NOTE:

Do not start engine.

Improper installation of EVAP service port adapter to the EVAP service port may cause a leak.
WITH CONSULT-II
1. Attach the EVAP service port adapter securely to the EVAP service port.
2. Also attach the pressure pump and hose to the EVAP service port adapter.
3. Turn ignition switch ON.
4. Select the “EVAP SYSTEM CLOSE” of “WORK SUPPORT
MODE” with CONSULT-II.
5. Touch “START”. A bar graph (Pressure indicating display) will
appear on the screen.
6. Apply positive pressure to the EVAP system until the pressure
indicator reaches the middle of the bar graph.
7. Remove EVAP service port adapter and hose with pressure
pump.
8. Locate the leak using a leak detector. Refer to EC-33, "
EVAPO-
RATIVE EMISSION LINE DRAWING" .
PEF 8 38 U
PEF 9 17 U
SEF 2 00 U

IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
EC-47
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: October 20052005 QX56
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)PFP:28591
DescriptionUBS00L1L

If the security indicator lights up with the ignition switch in
the ON position or “NATS MALFUNCTION” is displayed on
“SELF-DIAG RESULTS” screen, perform self-diagnostic
results mode with CONSULT-II using NATS program card.
Refer to BL-137, "
IVIS (INFINITI VEHICLE IMMOBILIZER
SYSTEM-NATS)" .

Confirm no self-diagnostic results of IVIS (NATS) is dis-
played before touching “ERASE” in “SELF-DIAG RESULTS”
mode with CONSULT-II.

When replacing ECM, initialization of IVIS (NATS) system
and registration of all IVIS (NATS) ignition key IDs must be
carried out with CONSULT-II using NATS program card.
Therefore, be sure to receive all keys from vehicle owner. Regarding the procedures of IVIS (NATS)
initialization and IVIS (NATS) ignition key ID registration, refer to CONSULT-II operation manual,
IVIS/NVIS.
SEF 5 43 X