ignition INFINITI QX4 2005 Factory Owner's Guide

AT-80
TROUBLE DIAGNOSIS
Revision: October 20052005 QX56
60
OthersVehicle runs with
transmission in “N”
position.
Refer to AT-182, "In
“N” Position, Vehicle
Moves" .ON vehicle1. PNP switchAT- 1 0 4
2. Fluid level and stateAT-5 0
3. Control cable adjustmentAT- 2 2 8
4. Control valve with TCMAT- 2 3 1
OFF vehicle5. Input clutchAT- 2 8 4
6. Gear systemAT- 2 5 0
7. Direct clutchAT- 2 9 6
8. Reverse brakeAT- 2 6 2
9. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 6
, AT-1 7 .)AT- 2 6 2
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 6
, AT- 1 7
.)AT- 2 6 2
61Engine does not start
in “N” or “P” position.
Refer to AT-180, "Engine Cannot Be
Started In “P” or “N”
Position" .ON vehicle1. Ignition switch and starterPG-4
, SC-
10
2. Control cable adjustmentAT- 2 2 8
3. PNP switchAT- 1 0 4
62Engine starts in posi-
tions other than “N” or
“P”.ON vehicle1. Ignition switch and starterPG-4
, SC-
10
2. Control cable adjustmentAT- 2 2 8
3. PNP switchAT- 1 0 4
63 Engine stall.ON vehicle1. Fluid level and stateAT-5 0
2. Engine speed signalAT - 11 3
3. Turbine revolution sensorAT- 1 3 1
4. Torque converter clutch solenoid valveAT - 11 5
5. CAN communication lineAT-9 5
6. Control valve with TCMAT- 2 3 1
OFF vehicle 7. Torque converterAT- 2 6 2
64Engine stalls when
select lever shifted “N”
→ “D”, “R”.ON vehicle1. Fluid level and stateAT-5 0
2. Engine speed signalAT - 11 3
3. Turbine revolution sensorAT- 1 3 1
4. Torque converter clutch solenoid valveAT - 11 5
5. CAN communication lineAT-9 5
6. Control valve with TCMAT- 2 3 1
OFF vehicle 7. Torque converterAT- 2 6 2
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-85
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
CONSULT-II SETTING PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.

For details, refer to the separate “CONSULT-II Operations Man-
ual”.
1. Turn ignition switch “OFF”.
2. Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector, which is located in instrument lower panel on
driver side.
3. Turn ignition switch “ON”. (Do not start engine.)
4. Touch “START (NISSAN BASED VHCL)”.
5. Touch “A/T”.
If “A/T” is not indicated, go to GI-39, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
6. Perform each diagnostic test mode according to each service
procedure.
SELF-DIAGNOSTIC RESULT MODE
Operation Procedure
After performing AT-85, "SELF-DIAGNOSTIC RESULT MODE" , place check marks for results on the AT-45,
"DIAGNOSTIC WORKSHEET" . Reference pages are provided following the items.
1. Perform “CONSULT-II SETTING PROCEDURE” Refer to AT - 8 5 , "
CONSULT-II SETTING PROCEDURE" .
2. Touch “SELF-DIAG RESULTS”.
Display shows malfunction experienced since the last erasing
operation.
BBIA0369E
BCIA0029E
BCIA0030E
BCIA0031E

AT-86
TROUBLE DIAGNOSIS
Revision: October 20052005 QX56
Display Items List
X: Applicable, —: Not applicable
Items (CONSULT-II
screen terms)Malfunction is detected when...TCM self-
diagnosisOBD-II (DTC)
“A/T” with
CONSULT-IIMIL indicator
lamp*1,
“ENGINE” with
CONSULT-II or
GST
CAN COMM CIRCUIT

When a malfunction is detected in CAN communications U1000 U1000
STARTER RELAY/
CIRC

If this signal is ON other than in P or N position, this is judged to be a
malfunction.
(And if it is OFF in P or N position, this too is judged to be a malfunc-
tion.)P0615 —
TCM

TCM is malfunctioning. P0700 P0700
PNP SW/CIRC

PNP switch 1-4 signals input with impossible pattern

“P” position is detected from N position without any other position
being detected in between.P0705 P0705
VEH SPD SEN/CIR AT
(Revolution sensor)

Signal from vehicle speed sensor A/T (Revolution sensor) not input
due to cut line or the like

Unexpected signal input during running

After ignition switch is turned ON, unexpected signal input from vehicle
speed sensor MTR before the vehicle starts movingP0720 P0720
ENGINE SPEED SIG

TCM does not receive the CAN communication signal from the ECM. P0725 —
TCC SOLENOID/CIRC

Normal voltage not applied to solenoid due to cut line, short, or the like P0740 P0740
A/T TCC S/V FNCTN

A/T cannot perform lock-up even if electrical circuit is good.

TCM detects as irregular by comparing difference value with slip rota-
tion.P0744 P0744*2
L/PRESS SOL/CIRC

Normal voltage not applied to solenoid due to cut line, short, or the like

TCM detects as irregular by comparing target value with monitor value.P0745 P0745
TCM·RAM

TCM memory (RAM) is malfunctioning. P1702 —
TCM·ROM

TCM memory (ROM) is malfunctioning. P1703 —
TP SEN/CIRC A/T

TCM does not receive the proper accelerator pedal position signals
(input by CAN communication) from ECM.P1705 P1705
ATF TEMP SEN/CIRC

During running, the ATF temperature sensor signal voltage is exces-
sively high or lowP1710 P0710
TURBINE REV S/CIRC

TCM does not receive the proper voltage signal from the sensor.

TCM detects an irregularity only at position of 4th gear for turbine revo-
lution sensor 2.P1716 P1716
VEH SPD SE/CIR·MTR

Signal (CAN communication) from vehicle speed sensor MTR not input
due to cut line or the like

Unexpected signal input during runningP1721 —
A/T INTERLOCK

Except during shift change, the gear position and ATF pressure switch
states are monitored and comparative judgement made.P1730 P1730
A/T 1ST E/BRAKING

Each ATF pressure switch and solenoid current is monitored and if a
pattern is detected having engine braking 1st gear other than in the "1"
position, a malfunction is detected.P1731 —
I/C SOLENOID/CIRC

Normal voltage not applied to solenoid due to functional malfunction,
cut line, short, or the like

TCM detects as irregular by comparing target value with monitor value.P1752 P1752

DTC U1000 CAN COMMUNICATION LINE
AT-95
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
DTC U1000 CAN COMMUNICATION LINEPFP:23710
DescriptionECS00CEQ
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
On Board Diagnosis LogicECS00CER

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “U1000 CAN COMM CIRCUIT” with CONSULT-II is detected when TCM cannot
communicate to other control units.
Possible CauseECS00CES
Harness or connectors
(CAN communication line is open or shorted.)
DTC Confirmation ProcedureECS00CET
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “ENGINE” with CONSULT-II.
3. Start engine and wait for at least 6 seconds.
4. If DTC is detected, go to AT - 9 8 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-II”.
BCIA0030E

AT-98
DTC U1000 CAN COMMUNICATION LINE
Revision: October 20052005 QX56
Diagnostic ProcedureECS00CEV
1. CHECK CAN COMMUNICATION CIRCUIT
With CONSULT-II
1. Turn ignition switch “ON” and start engine.
2. Select “SELF-DIAG RESULTS” mode for “A/T” with CONSULT-
II.
Is any malfunction of the
“CAN COMM CIRCUIT” indicated?
YES >> Print out CONSULT-II screen, GO TO LAN section.
Refer to LAN-3, "
Precautions When Using CONSULT-II"
.
NO >>INSPECTION END
PCIA0061E

DTC P0615 START SIGNAL CIRCUIT
AT-99
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
DTC P0615 START SIGNAL CIRCUITPFP:25230
DescriptionECS00CEW

TCM prohibits cranking other than at “P” or “N” position.
CONSULT-II Reference ValueECS00CEX
On Board Diagnosis LogicECS00CEY

This is not an OBD-II self-diagnostic item.

Diagnostic trouble code “P0615 STARTER RELAY/CIRC” with CONSULT-II is detected when park/neutral
(PNP) relay (starter relay) is switched “ON” other than at “P” or “N” position. (Or when switched “OFF” at
“P” or “N” position).
Possible CauseECS00CEZ

Harness or connectors
[The park/neutral position (PNP) relay (starter relay) and TCM circuit is open or shorted.]

Park/neutral position (PNP) relay (starter relay)
DTC Confirmation ProcedureECS00CF0
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Start engine.
4. Drive vehicle for at least 2 consecutive seconds.
5. If DTC is detected, go to AT - 1 0 1 , "
Diagnostic Procedure" .
Item name Condition Display value
STARTER RELAYSelector lever in “N”,“P” position. ON
Selector lever in other position. OFF
BCIA0030E

DTC P0615 START SIGNAL CIRCUIT
AT-101
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
TCM terminals and data are reference value. Measured between each terminal and ground.
Diagnostic ProcedureECS00CF2
1. CHECK STARTER RELAY
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “SELECTION FROM MENU” in “DATA MONITOR” mode
for “A/T” with CONSULT-II and check monitor “STARTER
RELAY” ON/OFF.
Without CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Check voltage between the IPDM E/R connector and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 2.
2. CHECK HARNESS BETWEEN A/T ASSEMBLY HARNESS CONNECTOR AND IPDM E/R CONEC-
TOR.
1. Turn ignition switch OFF.
2. Disconnect A/T assembly harness connector and IPDM E/R
connector.
3. Check continuity between A/T assembly harness connector and
IPDM E/R connector.
4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
OK or NG
OK >> GO TO 3.
NG >> Repair open circuit or short to ground or short to power in harness or connectors.
Terminal Wire color Item
ConditionData (Approx.)
9 B/R Starter relaySelector lever in "N" and "P" positions. Battery voltage
Selector lever in other positions. 0V
Item name Condition Display value
STARTER RELAYSelector lever in "N'', "P'' positions. ON
Selector lever in other positions. OFF
PCIA0056E
Item ConnectorTe r m i n a l
(Wirer color)Shift position Voltage (Approx.)
Starter
relayE12248
(B/R)Ground"N'' and "P'' Battery voltage
"R'' and "D'' 0V
LCIA0320E
Item ConnectorTerminal
(Wire color)Continuity
A/T assembly harness con-
nectorF9 9 (B/R)
Ye s
IPDM E/R connector E122 48 (B/R)
WCIA0427E

DTC P0700 TCM
AT-103
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
DTC P0700 TCMPFP:31036
DescriptionECS00CLQ
The TCM consists of a microcomputer and connectors for signal input and output and for power supply. The
TCM controls the A/T.
On Board Diagnosis LogicECS00CLR

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P0700 TCM” with CONSULT-II is detected when the TCM is malfunctioning.
Possible CauseECS00CLS
TCM.
DTC Confirmation ProcedureECS00CLT
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Start engine.
4. Run engine for at least 2 consecutive seconds at idle speed.
5. If DTC is detected, go to AT - 1 0 3 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “With CONSULT-II”.
Diagnostic ProcedureECS00CLU
1. CHECK DTC
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “SELF DIAG RESULTS” mode for “A/T” with CONSULT-
II.
3. Touch “ERASE”.
4. Turn ignition switch “OFF” and wait at least 10 seconds.
5. Perform DTC Confirmation Procedure, AT-103, "
DTC Confirma-
tion Procedure" .
Is the
“TCM” displayed again?
YES >> Replace the control valve with TCM. Refer to AT-231,
"Control Valve With TCM and A/T Fluid Temperature
Sensor 2" .
NO >>INSPECTION END
BCIA0030E
BCIA0031E

AT-104
DTC P0705 PARK/NEUTRAL POSITION SWITCH
Revision: October 20052005 QX56
DTC P0705 PARK/NEUTRAL POSITION SWITCHPFP:32006
DescriptionECS00CF3

The park/neutral position (PNP) switch includes a transmission position switch.

The transmission range switch detects the selector lever position and sends a signal to the TCM.
CONSULT-II Reference ValueECS00CF4
On Board Diagnosis LogicECS00CF5

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P0705 PNP SW/CIRC” with CONSULT-II is detected under the following condi-
tions.
–When TCM does not receive the correct voltage signal from the PNP switch 1, 2, 3, 4 based on the gear
position.
–When no other position but “P” position is detected from “N” positions.
Possible CauseECS00CF6

Harness or connectors
[The park/neutral position (PNP) switch 1, 2, 3, 4 and TCM circuit is open or shorted.]

Park/neutral position (PNP) switch 1, 2, 3, 4
DTC Confirmation ProcedureECS00CF7
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “ENGINE” with CONSULT-II.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 2
consecutive seconds.
THRTL POS SEN: More than 1.2V
5. If DTC is detected, go to AT-106, "
Diagnostic Procedure" .
WITH GST
Follow the procedure “With CONSULT-II”.
Item name Condition Display value
SLCTLVR POSI Selector lever in “N”,“P” positions. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
Selector lever in “4” position. 4
Selector lever in “3” position. 3
Selector lever in “2” position. 2
Selector lever in “1” position. 1
BCIA0030E

AT-106
DTC P0705 PARK/NEUTRAL POSITION SWITCH
Revision: October 20052005 QX56
Diagnostic ProcedureECS00CF9
1. CHECK PNP SW CIRCUIT
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “SELECTION FROM MENU” in “DATA MONITOR” mode
for “A/T” with CONSULT-II.
3. Check if correct selector lever position (N/P, R or D) is displayed
as selector lever is moved into each position.
OK or NG
OK >> GO TO 5.
NG >> GO TO 2.
2. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Perform TCM power supply and ground circuit. Refer to AT-168, "
MAIN POWER SUPPLY AND GROUND
CIRCUIT" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. DETECT MALFUNCTIONING ITEM
Check the following items:

A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
Item name Condition Display value
SLCTLVR POSISelector lever in “N”,“P” positions. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
Selector lever in “4” position. 4
Selector lever in “3” position. 3
Selector lever in “2” position. 2
Selector lever in “1” position. 1
PCIA0034E