light INFINITI QX50 2014 Navigation Manual

6. The selected destination is displayed atthe center of the map. Highlight [Start]
after confirming the location of the
displayed destination, and push
.
The system sets the destination to the
selected location and starts calculating
a route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
SETTING POINT ON MAP
It is possible to set a location scrolled to
on the map as the destination and have the
system calculate a route.
1. Scroll the map, place the cross pointerover the preferred location, and push
.
INFO:
.The map scale should be adjusted to
search for a location more effectively.
.The point on the blinking road where thecenter of the cross pointer is located can
be set as a destination.
2. Highlight [New Dest.] and push .
INFO:
For the items other than [New Dest.], refer to
“Map menu screen”.
“Scrolled location map screen”
(page 2-19)
3. The system sets the destination to the
selected location and starts calculating
a route.
4. Setting destination
4-23

4. Setting destination
4-24
INFO:
If a point on a freeway is set as the destination,
a confirmation message is displayed.
DELETE DESTINATION
It is possible to delete a destination and all
waypoints that have already been set.
1. Push.
2. Highlight [Next Page] and push . Select [Delete Destination]
and push .
3. A confirmation message is displayed.
Select [Yes] and push .
The destination and the waypoints are deleted.
INFO:
The deleted destination and waypoints are not
able to be reactivated.
Voice command
1. Push >on the steering wheel.
2. After the tone sounds, speak a com- mand.
To delete a destination and all way-
points:
“Delete Destination” (Alternate Com-
mand Mode)

5. Route guidance
5-2
PROCEDURES AFTER SETTING DESTINA-
TION
After performing a route search, the route
guidance can be immediately started. Also,
it is possible to confirm or change a route.
Available items after setting destination. [Start]:
Starts route guidance to the selected
destination.
“Starting route guidance”
(page 5-2)
. [More Routes]:
Displays 3 alternative routes.
“Selecting route” (page 5-3)
. [Add/Route Info]:
Displays the route information. A desti-
nation or a waypoint can also be
added.
“Confirming route” (page 5-3)
. [Move Location]:
Displays a map screen. The location of
the destination can be adjusted.
“Moving location of destination”
(page 5-5)
. [Store Location]:
Stores the location in the Address
Book.
“Storing location” (page 5-5)
. [Place Info]:
Displays information about the facility
that has been set as the destination, if
it is included in the map data.
“Viewing information about
searched location” (page 5-6)
INFO:
.
If no operations have been performed on the
system for several seconds, [Start] is auto-
matically selected, and the system starts
route guidance.
.When using waypoints, [More Routes] is
disabled. After the route is started, push
then select [Edit/Add to Route] to
change the route between each waypoint.
.The same screen as when [Move Location] is
selected can be displayed with the following
operations:
—Touching the map screen
—Pushing the directional buttons except
for the up/down button (INFINITI con-
troller with directional buttons)
—Pushing the slide switch except in the
upward/downward direction (INFINITI
controller without directional buttons)
STARTING ROUTE GUIDANCE
1. Highlight [Start] and push .
Route guidance starts.

SELECTING ROUTE
1. Highlight [More Routes] and push.
2. Highlight the preferred route conditionand push .
3. The display automatically returns to the map screen.
Available route conditions . [Short. Time] (purple):
Prioritizes by the shortest time. .
[Min. Freeway] (orange):
Minimizes the use of freeways.
. [Short. Dist.] (green):
Prioritizes by the shortest distance.
INFO:
.
When the route is selected, a preview is
displayed on the right side of the screen.
.The 3 routes may not always be different.
CONFIRMING ROUTE
1. Highlight [Add/Route Info] and push .
2. Highlight the preferred information item and push .
3. Push to return to the previous
screen.
Available information
. [Turn List]:
Displays the details of the suggested
route.
“Using turn list” (page 5-20)
. [Preview]:
The system will trace the planned route
going forward or in reverse.
“Using route preview” (page 5-21)
. [Add Way Pt.]:
Edits the route by adding a waypoint or
a destination.
“Adding destination or waypoint”
(page 5-4)
. [Store Route]:
Stores a calculated route. A maximum
of 5 routes can be stored. Stored routes
can be easily retrieved and set as the
suggested route.
5. Route guidance
5-3

5. Route guidance
5-4
“Storing route”(page 6-5)
. [Map Scroll]:
Displays a map screen where the
location of the destination can be
confirmed.
The same screen as when [Map Scroll]
is touched can be displayed with the
following operations:
—
Touching the map screen.
—Pushing the directional buttons except
for the up/down button (INFINITI con-
troller with directional buttons).
—Pushing the slide switch except in theupward/downward direction (INFINITI
controller without directional buttons).
Adding destination or waypoint
Before starting route guidance, destina-
tions and/or waypoints can be added. A
total of 6 destinations or waypoints can be
set.
1. Highlight [Add Way Pt.] and push .
2. Set additional destinations or way-
points and push .
The method of searching for a location
is the same as the one for a destina-
tion.
“4. Setting destination”
3. Highlight [Add Destination] or [Add Waypoint] and push .
4. The system starts calculating a route
that includes the added destination or
waypoint. When the calculation is
finished, the route is displayed.
INFO:
.
If a waypoint was added, [More Routes]
cannot be selected.

.If a destination was added, the prior
destination becomes a waypoint.
MOVING LOCATION OF DESTINATION
The location of the destination can be
adjusted by moving the cross pointer
across the map.
1. Highlight [Move Location] and push.
INFO:
The screen for adjusting the location also
changes by touching the map screen dis-
played on the right side of the screen.
2. Adjust the location by moving the crosspointer across the map and push
. The location of the destination
is modified.
INFO:
.
The map scale can be changed by turning
the center dial or touching the scale icon.
The map scale can also be changed by
pressing / (if so
equipped).
.The same screen as when [Move Location] is
touched can be displayed with the following
operations:
—Touching the map screen.
—Pushing the directional buttons except
up/down buttons (INFINITI controller
with directional buttons).
—Pushing the slide switch except upward/
downward (INFINITI controller without
directional buttons).
STORING LOCATION
A searched location can be stored in the
Address Book. Then it can be easily
retrieved and set as a destination (or
waypoint).
1. Highlight [Store Location] and push .
5. Route guidance
5-5

5. Route guidance
5-10
Split screen settings
The display setting on the left-hand side
screen shown during route guidance can
be changed.
1. Pushwhile the current location
map screen is displayed.
2. Highlight [Map View] and push .
3. Highlight [View Settings] and push
. 4. Highlight the preferred screen and
push . The indicator of the
selected screen illuminates.
Intersection:
The map screen and the enlarged intersec-
tion view can be displayed at the same
time.
Push

display the fuel economy information,
push

5. Route guidance
5-12
freeway or toll road, all exits along the
route which have exit information will be
shown in the turn list. The exit information
is shown as icons.
Displaying turn list automatically on free-
way:
When [Auto. Show Turn List on Freeway] is
set to ON, the turn list will be automatically
displayed while the vehicle travels on a
freeway or toll road.
Selecting a waypoint from the exit infor-
mation list:
When exit information is displayed on the
turn list, a waypoint to a facility located
near the freeway exit can be set as a
waypoint.
1. Highlight the exit where the exit in-formation icon is displayed, and push
. The category list screen is
displayed.
2. Highlight the landmark category andpush . The list screen for
showing facilities located near the
freeway exit is displayed.
3. Highlight the preferred facility for the waypoint and push .
4. The waypoint is set, and the route
search is performed.
“Procedures after setting destina-
tion” (page 5-2)

ROUTE SCREEN
WARNING!
Always stop the vehicle in a safe location
before modifying the route conditions.
Modifying the route conditions while driving
may cause an accident.
During route guidance, the route condi-
tions can be modified and the route
information can be confirmed. Set route
conditions according to personal prefer-
ence.
BASIC OPERATION
1. Push.
2. Highlight the preferred setting item and push .
3. Push