light INFINITI QX50 2015 Quick Reference Guide

15
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a
constant cruising speed once the vehicle has
reached 25 MPH (40 km/h).

The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.

To activate the cruise control, push the ON/OFF
switch
1. The CRUISE indicator light in the
instrument panel will illuminate.

To set a cruising speed, accelerate the vehicle to the desired speed, pu\
sh the COAST/SET
switch

2 and release. The SET indicator light
in the instrument panel will illuminate. Take
your foot off the accelerator pedal. Your vehicle will maintain the set \
speed.

To reset at a faster cruising speed, push and hold the ACCEL/RES switch 3. When the
vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch 2. Release the
switch when the vehicle slows to the desired speed.

To cancel the preset speed, tap the brake pedal or push the CANCEL switch 4.

To turn off cruise control, push the ON/OFF switch
1. Both the CRUISE indicator light and
the SET indicator light
in the instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
4
2
USB/iPod® Interface

The USB jack
1 is located in the center console
under the armrest.

When a compatible USB memory device or iPod® is
plugged into the USB jack, compatible audio and
video files stored on the device can be
played through the vehicle’s audio system
and front display.
For more information, refer to the “Monitor, climate, audio,
phone and voice recognition systems (section 4)” of your
Owner’s Manual.
3
1
1
1923534_15c_Infiniti_QX50_QRG_122314.indd 1512/23/14 1:05 PM

16
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button
1 for less
than 1.5 seconds. The CRUISE indicator light 2

will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch 3 and release
it. Cruise control will be set to the desired speed.

Press the distance button
4 repeatedly to change
the set distance between long, middle and short.

When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed indicator
lights will illuminate
5 in set mode.
When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance and set
vehicle speed indicator lights will illuminate
6 in set mode.

To reset at a faster cruising speed, push up and hold the ACCEL/RES
switch

7. When the vehicle attains the desired speed, release
the switch.

To reset at a slower cruising speed, push down and hold the COAST/SET switch 3. Release
the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
8 or tap the brake pedal. The set
vehicle speed indicator 5 will extinguish.
To turn off cruise control, press the CRUISE ON/OFF button 1. The CRUISE indicator
light
2 in the instrument panel will extinguish.
To set conventional (fixed speed) cruise control mode:

While cruise control is off, press the CRUISE ON/OFF
button 1
and hold it down for more
than 1.5 seconds. The CRUISE indicator light will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control should be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off\
, and then turn it on
again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
8
7
first drive features
1
2
3
4
5
6
1923534_15c_Infiniti_QX50_QRG_122314.indd 1612/23/14 1:05 PM

23
Navigation System (if so equipped)
Your Navigation System can calculate a route from your current location \
to a preferred
destination. The real-time map display and turn-by-turn voice guidance w\
ill lead you along
the route.

The Navigation System will continually update your vehicle’s position\
. If you have deviated
from the original route, it will recalculate the route from your current\
location.
1 Touch-screen display
2 DEST button – Press to enter a destination.
3 STATUS button – Press multiple times to display audio information with eith\
er the air

conditioner status, fuel economy or navigation directions.
4 ZOOM OUT button – Press to zoom the map out.
5 ROUTE button – Press to access the guidance control functions (guidance c\
ancellation, route

priority, waypoint setting on the route, etc.).
6 INFINITI Controller
• ENTER button – Press to select the highlighted item on the screen. If this\
button is pressed
while a map is displayed, the map menu screen is displayed.
• Main directional buttons – Use to move across the map, highlight an i\
tem on the screen or
adjust a setting (volume, brightness, etc.).
• Additional directional buttons – Use to move across the map or highli\
ght an item on the
character input screen.
• Center dial – Use to highlight an item on the screen or adjust a sett\
ing. The center dial can
also be used to adjust the map scale.
23
456
1
78
91011
1213
1923534_15c_Infiniti_QX50_QRG_122314.indd 2312/23/14 1:05 PM

25
HomeLink® Universal Transceiver (if so equipped)
The HomeLink® Universal Transceiver can learn
and consolidate the functions of up to 3 different
hand-held transmitters, operating items such as
garage doors, property gates, outdoor and indoor
lights or alarm systems.

To program the Homelink® Universal Transceiver:
• Position the handheld transceiver 1-3 in (26-76
mm) away from the HomeLink surface, keeping the HomeLink indicator ligh\
t in view.
• Press and hold the desired HomeLink button and the handheld transmitter \
button
simultaneously until the HomeLink indicator light flashes slowly and the\
n rapidly.
• Both buttons may be released when the indicator light flashes rapidly.

To verify the programing is complete, press and hold the HomeLink button\
and observe the
indicator light:
• A solid, continuous light indicates the programing is complete and the H\
omeLink button
will activate your device.
• A blinking light that turns to a solid, continuous light after 2 seconds\
indicates additional
steps are required to complete the programing.

An additional person may make the remaining steps easier. To complete th\
e
programing process:
• At the receiver of the device that you are programing to the HomeLink, p\
ress and
release the “learn” or “smart” button (the name may vary by\
manufacturer but it is
usually located near where the hanging antenna wire is attached to the u\
nit). You have
approximately 30 seconds to initiate the following step.
• Press and hold the programed HomeLink button for 2 seconds and release.

You may have to repeat the previous 2 steps up to 3 times to complete th\
e programing
process. HomeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website at
www.homelink.com or call 1-800-355-3515.
HOMELINK
1923534_15c_Infiniti_QX50_QRG_122314.indd 2512/23/14 1:05 PM