alarm INFINITI QX50 2016 Quick Reference Guide

7
first drive features
INFINITI Intelligent Key System
The INFINITI Intelligent Key System allows you to lock
or unlock your vehicle, open your liftgate and start the
engine. It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).
LOCKING AND UNLOCKING YOUR VEHICLE

The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.

To lock the vehicle, push either door handle request
switch
1 or the liftgate request switch 2 or press
the
button 3 on the key fob.

To unlock the vehicle, perform one of the
following procedures:
• Push either door handle request switch
1 or the liftgate request
switch
2; the corresponding door will unlock. Push the door handle
request switch
1 or the liftgate request switch 2 again within 1
minute; all other doors will unlock, or
• Press the
button 4 on the key fob to unlock the driver’s side
door. Press the
button 4 again; all other doors will unlock.

The Intelligent Key can also be used to activate the panic alarm by
pressing and holding the
button 5 for more than 1 second. Once
activated, the panic alarm and headlights will stay on for a period
of time.
INFINITI INTELLIGENT KEY BATTERY DISCHARGE

If the battery in the Intelligent Key is almost
discharged, the guide light
6 of the Intelligent Key
port blinks and the Intelligent Key insertion indicator
7 is displayed in the vehicle information display.

To start the engine under these circumstances,
insert the Intelligent Key into the key port with the
key ring side facing backward until it latches into
place. Then push the ignition switch to start
the engine.

To remove the Intelligent Key from the port, push the
ignition switch to turn the engine off and then pull
the Intelligent Key out of the port.

The Intelligent Key port does not charge the
Intelligent Key battery. If you see the Intelligent
Key warning light
8, replace the battery in the
Intelligent Key.

Do not insert the mechanical key or other objects into
the key port because they will damage the key port.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the “Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
F E
1
2
3
4
5
6
7
8
2128163_16b_QX50_US_pQRG_091515.indd 79/15/15 2:55 PM

26
HomeLink® Universal Transceiver (if so equipped)
The HomeLink® Universal Transceiver can learn and consolidate the functions of up to \
three different hand-held transmitters, operating items such as garage d\
oors, property
gates, outdoor and indoor lights or alarm systems.

To program the Homelink® Universal Transceiver:
• Position the handheld transceiver 1-3 in (26-76 mm) away from the Home\
Link surface,
keeping the HomeLink indicator light in view.
• Press and hold the desired HomeLink button and the handheld transmitter \
button
simultaneously until the HomeLink indicator light flashes slowly and the\
n rapidly.
• Both buttons may be released when the indicator light flashes rapidly.

To verify the programing is complete, press and hold the HomeLink button\
and observe the
indicator light:
• A solid, continuous light indicates the programing is complete and the H\
omeLink button
will activate your device.
• A blinking light that turns to a solid, continuous light after 2 seconds\
indicates additional
steps are required to complete the programing.

An additional person may make the remaining steps easier. To complete th\
e
programing process:
• At the receiver of the device that you are programing to the HomeLink bu\
tton, press
and release the “learn” or “smart” button (the name may var\
y by manufacturer, but it is
usually located near where the hanging antenna wire is attached to the u\
nit). You have
approximately 30 seconds to initiate the following step.
• Press and hold the programed HomeLink button for 2 seconds and release.

You may have to repeat the previous two steps up to three times to compl\
ete the
programing process. HomeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website at
www.homelink.com or call 1-800-355-3515.
HOMELINK
system guide
2128163_16b_QX50_US_pQRG_091515.indd 269/15/15 2:57 PM