ECO mode INFINITI QX50 2019 Owner's Manual

ADJUSTING THE SCREEN
The RearView Monitor settings can be
changed with the following procedure on the
upper display.1. Press the MENU button while the Rear- View Monitor screen is shown on the
upper display.
2. Touch the “Settings” key and then the “Camera/Sonar” key.
3. Touch the “Display” key. Select a pre- ferred item, “Brightness”, “Tint”, “Color”,
“Contrast” and “Black Level” of the Rear-
View Monitor and adjust the value by
touching the “+” or “-” key. Touch “Reset Settings” to return all settings
to default.
You can also press the
button and ei-
ther turn or move the INFINITI controller to
adjust the day/night settings. Pressing
the
button again will switch the screen
to AUTO mode. While the adjustment screen
is shown on the upper display you can also
touch either “+” or “-” key.
The upper and lower display screens can be
turned on or off by pressing and holding
the
button.
NOTE:
Do not adjust the Brightness, Tint, Color,
Contrast and Black Level of the RearView
Monitor while the vehicle is moving. Make
sure the parking brake is firmly applied.
HOW TO TURN ON AND OFF
PREDICTED COURSE LINES
To toggle on and off the predicted course
lines while in the P (Park) position: 1. Press the MENU button.
2. Touch the “Settings” key.
3. Touch the “Camera/Sonar” key.
4. Touch the “Camera” key. 5. Touch the “Predicted Course Lines” key
to turn the feature on or off.
When the predicted course lines are
turned on, the indicator light is on.
REARVIEW MONITOR SYSTEM
LIMITATIONS
WARNING
Listed below are the system limitations for
RearView Monitor. Failure to operate the
vehicle in accordance with these system
limitations could result in serious injury or
death.
∙ The system cannot completely eliminateblind spots and may not show every
object.
∙ Underneath the bumper and the corner areas of the bumper cannot be viewed on
the RearView Monitor because of its
monitoring range limitation. The system
will not show small objects below the
bumper, and may not show objects close
to the bumper or on the ground.
∙ Objects viewed in the RearView Monitor differ from actual distance because a
wide-angle lens is used.
LHA4243
Monitor, climate, audio, phone and voice recognition systems4-9

4. Maneuver the steering wheel to makethe vehicle width guide lines
Dparallel
to the parking space
Cwhile referring
to the predicted course lines.
5. When the vehicle is parked in the space completely, press the Park button lo-
cated near the shift lever to place the
vehicle in the P (Park) position and apply
the parking brake.
HOW TO SWITCH THE DISPLAY
With the ignition switch in the ON position,
press the
CAMERA button or with the
engine running, move the shift lever to the R
(Reverse) position to operate the Around
View® Monitor.
The Around View® Monitor displays differ-
ent split screen views depending on the posi-
tion of the shift lever. When activating the
Around View® Monitor, the guide lines, the
icons and the messages may not be displayed
immediately. Press the
CAMERA but-
ton or touch the “Change View” key to switch
between the available views.
If the shift lever is in the R (Reverse) position,
the available views are:
∙ Rear view/bird’s-eye view split screen ∙ Rear view/front-side view split screen
∙ Rear-wide view
If the shift lever is in the P (Park) position, the
available views are: ∙ Front view/bird’s-eye view split screen
∙ Front view/front-side view split screen
∙ Front-wide view
If the shift lever is in the D (Drive) position, the
only available views are: ∙ Front view/bird’s-eye view split screen
∙ Front view/front-side view split screen
∙ Front-wide view
The display will switch from the Around
View® Monitor screen when: ∙ The shift lever is in the D (Drive) position and the vehicle speed increases above
approximately 6 mph (10 km/h).
∙ A different screen is selected.
AROUND VIEW® MONITOR
SETTINGS
To set up the Around View® Monitor to your
preferred settings, press the MENU button,
select the “Settings” key, then select the
“Camera/Sonar” key on the lower display
then select the “Camera” key.
For additional information about the sonar,
refer to “Camera aiding sonar (parking sen-
sor)” in this section. For information about the
Display screen adjustment, refer to “Adjust-
ing the screen” in this section.
Designs and items displayed on the screen
may vary depending on model.
LHA4265
4-20Monitor, climate, audio, phone and voice recognition systems

Touch “Reset Settings” to return all settings
to default.
You can also press and hold
the
CAMERA button and either turn or
move the INFINITI controller to the left or the
right to adjust the day/night settings. Press-
ing and holding the
CAMERA button
again will switch the screen to AUTO mode.
While the adjustment screen is shown on the
upper display you can also touch either “+” or
“-” key.
NOTE:
Do not adjust the Brightness, Tint, Color,
Contrast and Black Level of the Around
View® Monitor while the vehicle is moving.
Make sure the parking brake is firmly ap-
plied.
AROUND VIEW® MONITOR
SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for
Around View® Monitor. Failure to operate
the vehicle in accordance with these system
limitations could result in serious injury or
death.
∙ Do not use the Around View® Monitor with the outside mirrors in the stored po-
sition, and make sure that the liftgate is
securely closed when operating the ve-
hicle using the Around View® Monitor.
∙ The apparent distance between objects viewed on the Around View® Monitor
differs from the actual distance.
∙ The cameras are installed on the front grille, the outside mirrors and above the
rear license plate. Do not put anything on
the vehicle that covers the cameras.
∙ When washing the vehicle with high pressure water, be sure not to spray it
around the cameras. Otherwise, water
may enter the camera unit causing water
condensation on the lens, a malfunction,
fire or an electric shock.
LHA4348
4-22Monitor, climate, audio, phone and voice recognition systems

Sonar function settings
To set up the sonar function to your preferred
settings, press the MENU button, select the
“Settings” key, select the “Camera/Sonar” key
and then select the “Sonar” key on the lower
display.
Designs and items displayed on the screen
may vary depending on the models.
Sonar:When this item is turned to ON, the
front and rear sonar is activated and a sonar
indicator
Cwill appear at the corner of the
vehicle to inform the driver when an obstacle
is near. Another sonar indicator
Dmay also
appear on either a side view, front or rear- wide view Around View® Monitor screen to
aid the driver when an object is near. When
this item is turned off (indicator turns off), the
front and rear sonar is deactivated. The am-
ber markers are displayed at the corners of
the vehicle icon and the sonar icon will disap-
pear from the “
” keyAon the Around
View® Monitor display. The next time the
ignition switch is placed in the on position, a
gray sonar icon will briefly flash on the upper
display, indicating that the sonar system is
off.
FR sensor only: When this item is turned to
“ON”, only the front sonar sensors are active.
Interrupt Display: When this item is turned to “ON” the upper display screen will interrupt
the current view in the display to see the
surrounding area of the vehicle.
Sonar Sensitivity:
Adjust the sensitivity level
of the sonar by touching either the “+” or “-” on
the menu screen.
Sonar Volume: Adjust the volume of the
buzzer by touching either the “+” or the “-” on
the menu screen.
SONAR SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for
the sonar function. Failure to operate the
vehicle in accordance with these system
limitations could result in serious injury or
death.
∙ Inclement weather or ultrasonic sources such as an automatic car wash, a truck’s
compressed-air brakes or a pneumatic
drill may affect the function of the sys-
tem, including reduced performance or a
false activation.
∙ The system is not designed to prevent contact with small or moving objects.LHA4609LHA4610
Monitor, climate, audio, phone and voice recognition systems4-27

When the MOD system detects moving ob-
jects near the vehicle, a yellow frame will be
displayed on the view where the objects are
detected. While the MOD system continues
to detect moving objects, the yellow frame
continues to be displayed.
NOTE:
While the sonar/BCI chime (if so equipped) is
beeping, the MOD system does not chime.
In the bird’s-eye view, the yellow frame
1is
displayed on each camera image (front, rear,
right, left) depending on where moving ob-
jects are detected. The yellow frame
2is displayed on each
view in the front view and rear view modes.
A blue MOD icon
3is displayed in the view
where the MOD system is operative. A gray
MOD icon is displayed in the view where the
MOD system is not operative.
If the MOD system is turned off, the MOD
icon
3is not displayed.
Rear-wide view
LHA4562
4-32Monitor, climate, audio, phone and voice recognition systems

1. Lower touch-screen display (lowerdisplay)
2.
Temperature control increase
button (passenger’s side)
3.
Temperature control decrease
button (passenger’s side) 4.
Air recirculation button
5.
Front defroster button
6.
Rear window and outside mir-
ror (if so equipped) defroster switch
7. ON-OFF button
8.
CLIMATE button 9.
MENU button
10.
Manual air flow control button
11.
Fan speed decrease button
12.
Fan speed increase button
13. AUTO button
14.
Temperature control decrease
button (driver’s side)
15.
Temperature control increase
button (driver’s side)
WARNING
∙ The air conditioner cooling function op- erates only when the engine is running.
∙ Do not leave children or adults who would normally require the assistance of
others alone in your vehicle. Pets should
also not be left alone. They could acciden-
tally injure themselves or others through
inadvertent operation of the vehicle.
Also, on hot, sunny days, temperatures in
a closed vehicle could quickly become
high enough to cause severe or possibly
fatal injuries to people or animals.
∙ Do not use the recirculation mode for long periods as it may cause the interior
air to become stale and the windows to
fog up.
LHA4574
HEATER AND AIR CONDITIONER
(automatic)
4-36Monitor, climate, audio, phone and voice recognition systems

Start the engine and operate the controls to
activate the air conditioner.
NOTE:∙ Odors from inside and outside the vehicle can build up in the air conditioner unit.
Odor can enter the passenger compart-
ment through the vents.
∙ When parking, set the heater and air con- ditioner controls to turn off air recircula-
tion to allow fresh air into the passenger
compartment. This should help reduce
odors inside the vehicle.
AUTOMATIC OPERATION
Press the AUTO button to set the automatic
control mode that keeps the air distribution,
temperature and the fan speed automati-
cally.
Cooling and/or dehumidified
heating (AUTO)
This mode may be used all year round as the
system automatically works to keep a con-
stant temperature. Air flow distribution, air
intake control, and fan speed are also con-
trolled automatically. 1. Press the
CLIMATE button on the
lower display menu. The CLIMATE
screen will display on the lower display.
2. Press the AUTO button on. (The indica- tor on the button will illuminate and
AUTO will be displayed on the CLIMATE
screen.)
3. Press the
temperature con-
trol buttons on the driver’s side to set the
desired temperature.
∙ The temperature of the passenger com- partment will be maintained automati-
cally. Air flow distribution, air intake con-
trol and fan speed are also controlled
automatically.
∙ A visible mist may be seen coming from the vents in hot, humid conditions as the
air is cooled rapidly. This does not indi-
cate a malfunction.
Dehumidified defrosting or
defogging
1. Press thefront defroster button
on. (The indicator light on the button will
come on.) 2. Operate the
temperature
control buttons to set the desired tem-
perature.
∙ To quickly remove ice from the outside of the windows, use the
fan speed
control button or the
key to set the
fan speed to maximum.
∙ As soon as possible after the windshield is clean, press the AUTO button to return
to the automatic mode.
∙ When the
front defroster button is
pressed, the air conditioner will auto-
matically be turned on at outside tem-
peratures approximately 32°F (0°C) to
defog the windshield. The air recirculate
mode automatically turns off, allowing
outside air to be drawn into the passen-
ger compartment to further improve the
defogging performance.
Remote Engine Start with
Intelligent Climate Control (if so
equipped)
Vehicles equipped with automatic climate
controls and Remote Engine Start function
may go into automatic heating or cooling
mode when Remote Engine Start is activated
depending on outside and cabin tempera-
Monitor, climate, audio, phone and voice recognition systems4-37

tures. During this period, the climate control
display and buttons will be inoperable until
the ignition switch is turned on. In Remote
Engine Start defrosting mode, the rear win-
dow defroster, heated seat (if so equipped)
and heated steering wheel (if so equipped)
may be activated automatically. In Remote
Engine Start cooling mode, the climate con-
trolled seat (if so equipped) may be activated
automatically.
Voice Recognition logic (if so
equipped)
When the climate control system is on, the
fan speed may be automatically lowered so
that commands are more easily recognized.
Fan speed can be adjusted using the
fan
speed decrease and
increase buttons, if
desired.
MANUAL OPERATION
Fan speed control
Press thefan speed increase andfan speed decrease buttons to manually con-
trol the fan speed. Fan speed can also be
controlled by touching the
orkeys
on the lower display.
Press the AUTO button to return to auto-
matic control of the fan speed.
Temperature control
Press thetemperature control
buttons up or down to set the desired tem-
perature.
The temperature can be set within the fol-
lowing range:
∙ For U.S.: 60 to 90ºF (16 to 32ºC)
∙ For Canada: 64 to 90ºF (18 to 32ºC)
Air recirculation
Press theair recirculation button to re-
circulate interior air inside the vehicle.
The
indicator light on the button will
come on.
The air recirculation cannot be activated
when the air conditioner is in the
front
defrosting mode.
When the outside temperature exceeds 70°F
(21°C), the air conditioning system may de-
fault to air recirculation mode automatically
to reduce overall power consumption. To exit
air recirculation mode, deselect the
air
recirculation button (indicator will turn off) to
enter fresh air mode.
Automatic intake air control
In the AUTO mode, the intake air will be
controlled automatically. To manually control
the intake air, press the
air recirculation
button. To return to the automatic control
mode, press and hold the
air recircula-
tion button for about 2 seconds. The indica-
tor light will flash twice, and then the intake
air will be controlled automatically.
Air flow control
Press thebutton to manually control
air flow. Pressing the button repeatedly will
cycle through the available modes and dis-
play the corresponding icon on the lower dis-
play. Air flow can also be controlled by touch-
ing the
key on the lower display:
— Air flows from center and side
vents.
— Air flows from center and sidevents and foot outlets.
— Air flows mainly from footoutlets.
— Air flows from defroster andfoot outlets.
To turn system off
Press the ON-OFF button.
4-38Monitor, climate, audio, phone and voice recognition systems

CLIMATE button
Press theCLIMATE button to show the
CLIMATE screen on the lower display.
Rear window and outside mirror (if
so equipped) defroster switch
For additional information, refer to “Rear
window defroster, outside mirror defroster,
and wiper deicer (if so equipped) switch” in
the “Instruments and controls” section of this
manual.
OPERATING TIPS
The sensors,AandBon the instrument
panel, help the system maintain a constant
temperature. Do not put anything on or
around these sensors. ∙ When the engine coolant temperature
and outside air temperature are low, the
air may flow from defroster or foot out-
lets to initialize automatic heating mode.
This is not a malfunction. After the cool-
ant temperature warms up, air will flow
normally from the foot outlets.
∙ A visible mist may be seen coming from the ventilators in hot, humid conditions as
the air is cooled rapidly. This does not
indicate a malfunction.
LHA4686
Monitor, climate, audio, phone and voice recognition systems4-39

CLIMATE SETTING SCREEN
Climate control settings can be changed on
the screen.
Available setting items may vary depending
on models and specifications.
Press the
CLIMATE button on the
lower display menu. The CLIMATE screen
will display on the lower display.
Heating (A/C off)
The air conditioner does not activate in this
mode. When you need to heat only, use this
mode. 1. Press the
CLIMATE button.
2. If the Climate system is off, press the ON-OFF button to turn the system on.
3. If the
A/C indicator is on, touch
the
A/C key to turn the A/C off.
4. Press the
temperature con-
trol buttons on the driver’s side to set the
desired temperature.
∙ When in AUTO mode, the temperature of the passenger compartment will be
maintained automatically. Air flow distri-
bution and fan speed are also controlled
automatically.
∙ Do not set the temperature lower than the outside air temperature or the system
may not work properly.
∙ This procedure is not recommended if windows fog up.
When the outside temperature decreases to
approximately 32°F (0°C), the A/C function
does not activate even if the
A/C indi-
cator light illuminates.
Air conditioning (A/C)
Touch theA/C key to turn the A/C
mode on or off. Turn on the A/C mode for effective cooling and dehumidifying. When
the A/C indicator light is on, the A/C mode is
on.
Sync mode setting
The driver’s, passenger’s and rear (if so
equipped) temperature setpoints can be syn-
chronized using the
SYNC key on the
lower display. When the key is touched, tem-
perature settings become synchronized and
the SYNC indicator turns on.
∙ If the driver’s side temperature buttons are pressed, the driver’s side, passenger’s
side, and rear (if so equipped) tempera-
ture settings will update simultaneously.
∙ If the passenger’s side or rear (if so equipped) temperature buttons are
pressed, Sync mode will exit, the indicator
light will go off, and the temperature will
update based on the button pressed.
Driver’s side temperature will remain the
same until manually changed.
Steering wheel heater (if so
equipped)
Touch theSteering Heater key on the
CLIMATE screen on the lower display to turn
the steering wheel heater on or off. When the
steering wheel heater is on, the indicator light
is on.
LHA4579
4-40Monitor, climate, audio, phone and voice recognition systems