ignition INFINITI QX50 2019 Quick Reference Guide

4
Instrument Panel
Upper display/Navigation System (if so equipped)
Automatic heater and air conditioner controls
Lower display
Audio control panel
Shift lever
Push-button ignition switch
Hood latch release
Lower switch bank


•
Instrumen
t brightness control


•
F
ront and rear sonar switch (if so equipped)
•


S
teering assist switch (if so equipped)


•
P
ower liftgate switch


•
H
eadlight control switch


•
F
og light switch (if so equipped)


•
H
ead Up Display (HUD) switch (if so equipped)


•
Dynamic driv
er assistance switch (if so equipped)

7
To turn the rain sensor function on and off:
1.

Pr
ess the MENU button below the lower display.
2.


T
ouch the “Settings” key and then the “Vehicle” key
on the display.
3

.



T

ouch the “Rain Sensor” key
to toggle the
feature ON and OFF.
When the rain-sensing function is disabled, the AUTO
position on the wiper stalk will work in conventional
intermittent mode.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position
in order to replace the wiper blades.
To move the wiper blades to the service position:
•


When the ignition swit

ch is in the ON position or
within 60 seconds of placing the ignition switch
in the OFF position, lift the windshield wiper and
washer lever upwards twice in less than 0.5 seconds.
The windshield wipers will move to the service
position automatically, and the wiper blades can now be replaced.
To move the wiper blades back to the original position:


•

Plac

e the wiper arm in the down position and lift the wiper and washer lever up
for more than 1 second, or lower the lever down to operate at any wiper speed.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and
feature information.
Wiper and Washer Switch
Move the lever up or down to one of the following
positions to operate the windshield wipers:
MIST
One sw

eep operation
OFF

Wipers ar

e OFF
AUTO

Speed-sensing and r
ain-sensing automatic wipe
(if so equipped)
LO



C

ontinuous wipe, slow
HI

C

ontinuous wipe, fast
To adjust the wiper sensitivity for the AUTO setting,
twist the control ring
. Pull the lever toward you to
operate the windshield washer.
REAR WIPER AND WASHER
Turn the rear wiper switch
to one of the following
positions to operate the rear wiper:
OFF

Wiper

is OFF
Intermittent wipe
Continuous wipe
Push the lever
forward to operate the rear
windshield washer.

9
Electronic Shift Lever
To put the vehicle in N (Neutral):
Press the button
, then push the
electronic shift lever forward until you feel
resistance and release the shift lever, or
pull the electronic shift lever back until you
feel resistance and release the shift lever.
To put the vehicle in R (Reverse):
Press the button
, then push the
electronic shift lever forward past the
point of resistance and release the shift
lever.
To put the vehicle in D (Drive):
Press the button
and pull the electronic
shift lever back past the point of
resistance and release the shift lever.
To put the vehicle in P (Park):
Make sure the vehicle is completely stopped and press the P (Park)
button
.
If you switch the ignition off with the transmission in D (Drive) or
R (Reverse), the transmission automatically shifts into the P (Park) position.
If you open the driver’s door while the vehicle is stationary or moving at a
very low speed, the vehicle automatically switches into the P (Park) position.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
Your vehicle is equipped with two USB ports, located under the
control panel, to which you can connect compatible devices
(cellular phones, iPods, other compatible audio devices, USB
memory sticks, etc.).
After connecting your device through one of the USB ports,
press the MEDIA button on the control panel to select audio
playback from the device connected through the USB ports.
A second device can be connected for charging. In order to
switch to the second device for audio playback, both devices will
need to be removed and the second device reconnected first.
There are also USB charging ports located in the first row on the
inside of the console box and in the second row on the back of
the center console. These ports will charge compatible devices.
Please see your INFINITI InTouch™ Owner’s Manual for important safety information,
system limitations, and additional operating and feature information.
USB Connection Ports

12
The Head Up Display can show Vehicle
Speed, Driving Aids and Navigation
on the center of the windshield. Press
the Head Up Display switch
on the
instrument panel to turn the system
ON and OFF.
To adjust the Head Up Display
settings, when the system is on:
1.


Pr

ess the MENU button below the
lower display.
2.


T

ouch the “Settings” key and then
the “Head Up Display” key
.
3

.



A

djust the positioning of the Head
Up Display on the windshield
by touching the arrows
, and
the brightness by touching the
brightness keys
.
To change what items are shown in the Head Up Display, touch the
“Display items” key
.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
Two positions for the driver’s seat,
steering column and outside mirrors
can be stored in the automatic
drive positioner memory. To set a
memory position:
1.


Plac
e the ignition switch in
the ON position. (The vehicle
should be stopped while setting the memory.)
2.


A
djust the driver’s seat, steering column and outside
mirrors to the desired positions using the adjusting switches for
each feature.
3

.
Push the
SET switch
, and within 5 seconds, push the
memory switch (1 or 2)
. The indicator light for the memory
switch you select will illuminate for approximately 5 seconds
and a chime will sound when the memory is stored.
The driver’s seat and steering column will automatically move when
the driver’s side door is opened, to allow the driver to get in and out
of the driver’s seat more easily. “Lift Steering Wheel on Exit” and
“Slide Driver Seat Back on Exit” can be adjusted in the lower
touch-screen display under “Vehicle Settings”.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
Automatic Drive Positioner
(if so equipped)Head Up Display (if so equipped)

18
Electronic Parking Brake
To apply the parking brake, pull the electric parking
brake switch
up, located below the instrument
panel, regardless of the ignition switch position.
To release the parking brake, push the electric
parking brake switch
down while the ignition is
on. The parking brake will be automatically released
when you depress the accelerator pedal as long
as certain conditions are met, such as having your
seatbelt fastened.
Please see your Owner’s Manual for important safety information,
system limitations, and additional operating and feature information.