ECO mode INFINITI QX50 2021 Quick Reference Guide

11
To turn the rain sensor function on and off:
1. Press the MENU button below the lower display.
2. Touch the “Settings” key and then the “Comfort &
Convenience” key
on the display.
3. Touch the “Rain Sensor” key
to toggle the
feature ON and OFF.
When the rain-sensing function is disabled, the AUTO
position on the wiper stalk will work in conventional
intermittent mode.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position in
order to replace the wiper blades.
To move the wiper blades to the service position:
• When the ignition switch is in the ON position or
within 60 seconds of placing the ignition switch
in the OFF position, lift the windshield wiper
and washer lever upwards twice in less than 0.5
seconds. The windshield wipers will move to the
service position automatically, and the wiper blades can now be replaced.
To move the wiper blades back to the original position:
• Place the wiper arm in the down position and lift the wiper and washer lever up
for more than 1 second, or lower the lever down to operate at any wiper speed.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and
feature information.
Wiper and Washer Switch
Move the lever up or down to one of the following
positions to operate the windshield wipers:
MIST
One sweep operation
OFF Wipers are OFF
AUTO Speed-sensing and rain-sensing automatic wipe
(if so equipped)
LO Continuous wipe, slow
HI Continuous wipe, fast
To adjust the wiper sensitivity for the AUTO setting,
twist the control ring
. Pull the lever toward you to
operate the windshield washer.
REAR WIPER AND WASHER
Turn the rear wiper switch
to one of the following
positions to operate the rear wiper:
OFF Wiper is OFF
Intermittent wipe
Continuous wipe
Push the lever
forward to operate the rear
windshield washer.

21
ProPILOT Assist (if so equipped)
PROPILOT INTELLIGENT CRUISE CONTROL
To accelerate or decelerate your vehicle to the desired
speed, push the RES+ switch
or SET- switch and
release it.
When a vehicle is detected in the lane ahead, the
Intelligent Cruise Control system controls the vehicle
speed based on the distance set by the driver.
To cancel a set speed, push the CANCEL switch
on the
steering wheel or tap the brake pedal.
To turn the system off, push the ProPILOT Assist switch
.
To choose the conventional (fixed speed) cruise control
mode, push and hold the ProPILOT Assist switch
for
longer than approximately 1.5 seconds.”
STOP-HOLD FEATURE:
When the vehicle ahead decelerates to stop, your vehicle
decelerates to a standstill if the ProPILOT Assist is
activated. Once the vehicle stops, the system will keep the
vehicle stopped.
If the vehicle is stopped for less than 3 seconds, and
the vehicle ahead begins to move, your vehicle will start
moving again automatically.
If the vehicle is stopped for more than 3 seconds, and the
vehicle ahead begins to accelerate, push and release the
RES+ switch
or the accelerator pedal. This will resume
the last set cruising speed.
ProPILOT Assist allows you to maintain
gap and “Stop-Hold” in-between vehicles
while also helping to keep you in the center
of your lane.
PROPILOT ASSIST DISPLAY
Set vehicle speed indicator: Displays
the speed set by the driver.
Steering Assist indicator: Shows
whether steering assist is active or
inactive (green-active, grey-standby).
Lane marker indicator: Appears green
on the display when lane lines are
detected and steering assist is active.
ProPILOT Assist status indicator:
Displays whether ProPILOT Assist is
engaged or not.
Vehicle ahead detection indicator:
Appears on the display when a vehicle
is detected ahead.
Set distance indicator: Displays the gap amount between the vehicle and the
preceding vehicle as set by driver (1 bar - shortest gap, 3 bars - longest gap).
To set ProPILOT Assist, push the ProPILOT Assist switch
on the steering
wheel. The ProPILOT Assist status
will appear on the vehicle information
display. When the desired cruising speed is reached push the SET- switch
and
release it.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.