Revers INFINITI QX56 2004 Factory Owner's Manual

AT-32
A/T CONTROL SYSTEM
Revision: August 20072004 QX56
CAN CommunicationUCS002CF
SYSTEM DESCRIPTION
Refer to LAN-5, "CAN Communication Unit" .
Input/Output Signal of TCMUCS002CG
*1: Spare for vehicle speed sensor·A/T (revolution sensor)
*2: Spare for accelerator pedal position signal
*3: If these input and output signals are different, the TCM triggers the fail-safe function.
*4: CAN communicationsControl itemLine
pressure
controlVehicle
speed
controlShift
controlLock-up
controlEngine
brake
controlFail-safe
function
(*3)Self-diag-
nostics
function
InputAccelerator pedal position signal
(*4)XXXXXXX
Vehicle speed sensor A/T
(revolution sensor)XXXX XX
Vehicle speed sensor MTR
(*1) (*4)XXXX X
Closed throttle position signal
(*4)(*2) X (*2) X X (*2) X X
Wide open throttle position signal
(*4)(*2) X (*2) X (*2) X X
Turbine revolution sensor 1 X X X X X
Turbine revolution sensor 2
(for 4th speed only)XX X XX
Engine speed signals
(*4)XX
PNP switch XXXXXXX
A/T fluid temperature sensors 1, 2 X X X X X X X
ICC or
ASCDOperation signal
(*4)XXXX
Overdrive cancel
signal
(*4)XXX
TCM power supply voltage signal X X X X X X
Out-
putDirect clutch solenoid (ATF pres-
sure switch 5)XX XX
Input clutch solenoid (ATF pressure
switch 3)XX XX
High and low reverse clutch sole-
noid (ATF pressure switch 6)XX XX
Front brake solenoid (ATF pressure
switch 1)XX XX
Low coast brake solenoid (ATF
pressure switch 2)XX XXX
Line pressure solenoid X X X X X X X
TCC solenoid X X X
Starte r re la yXX

A/T CONTROL SYSTEM
AT-37
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
Engine Brake ControlUCS002CK

The forward one-way clutch transmits the drive force from the engine to the rear wheels. But the reverse
drive from the rear wheels is not transmitted to the engine because the one-way clutch is idling.
Therefore, the low coast brake solenoid is operated to prevent the forward one-way clutch from idling and
the engine brake is operated in the same manner as conventionally.

The operation of the low coast brake solenoid switches the low coast brake switching valve and controls
the coupling and releasing of the low coast brake.
The low coast brake reducing valve controls the low coast brake coupling force.
Control ValveUCS002CL
FUNCTION OF CONTROL VALVE
SCIA1520E
Name Function
Torque converter regulator valveIn order to prevent the pressure supplied to the torque converter from being excessive,
the line pressure is adjusted to the optimum pressure (torque converter operating pres-
sure).
Pressure regulator valve
Pressure regulator plug
Pressure regulator sleeveAdjusts the oil discharged from the oil pump to the optimum pressure (line pressure) for
the driving state.
Front brake control valveWhen the front brake is coupled, adjusts the line pressure to the optimum pressure
(front brake pressure) and supplies it to the front brake. (In 1st, 2nd, 3rd, and 5th gears,
adjusts the clutch pressure.)
Accumulator control valveAdjusts the pressure (accumulator control pressure) acting on the accumulator piston
and low coast reducing valve to the pressure appropriate to the driving state.
Pilot valve AAdjusts the line pressure and produces the constant pressure (pilot pressure) required
for line pressure control, shift change control, and lock-up control.
Pilot valve BAdjusts the line pressure and produces the constant pressure (pilot pressure) required
for shift change control.
Low coast brake switching valve During engine braking, supplies the line pressure to the low coast brake reducing valve.
Low coast brake reducing valveWhen the low coast brake is coupled, adjusts the line pressure to the optimum pressure
(low coast brake pressure) and supplies it to the low coast brake.
N-R accumulator Produces the stabilizing pressure for when N-R is selected.
Direct clutch piston switching valve Operates in 4th gear and switches the direct clutch coupling capacity.
High and low reverse clutch control valveWhen the high and low reverse clutch is coupled, adjusts the line pressure to the opti-
mum pressure (high and low reverse clutch pressure) and supplies it to the high and low
reverse clutch. (In 1st, 3rd, 4th and 5th gears, adjusts the clutch pressure.)

AT-38
A/T CONTROL SYSTEM
Revision: August 20072004 QX56
FUNCTION OF PRESSURE SWITCH
Input clutch control valveWhen the input clutch is coupled, adjusts the line pressure to the optimum pressure
(input clutch pressure) and supplies it to the input clutch. (In 4th and 5th gears, adjusts
the clutch pressure.)
Direct clutch control valveWhen the direct clutch is coupled, adjusts the line pressure to the optimum pressure
(direct clutch pressure) and supplies it to the direct clutch. (In 2nd, 3rd, and 4th gears,
adjusts the clutch pressure.)
TCC control valve
TCC control plug
TCC control sleeveSwitches the lock-up to operating or released. Also, by performing the lock-up operation
transiently, lock-up smoothly.
Torque converter lubrication valveOperates during lock-up to switch the torque converter, cooling, and lubrication system
oil path.
Cool bypass valve Allows excess oil to bypass cooler circuit without being fed into it.
Line pressure relief valve Discharges excess oil from line pressure circuit.
N-D accumulator Produces the stabilizing pressure for when N-D is selected.
Manual valveSends line pressure to each circuit according to the select position. The circuits to which
the line pressure is not sent drain. Name Function
Name Function
Pressure switch 1 (FR/B)Detects any malfunction in the front brake hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
Pressure switch 2 (LC/B)Detects any malfunction in the low coast brake hydraulic pressure. When it detects any
malfunction, it puts the system into fail-safe mode.
Pressure switch 3 (I/C)Detects any malfunction in the input clutch hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
Pressure switch 5 (D/C)Detects any malfunction in the direct clutch hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
Pressure switch 6 (HLR/C)Detects any malfunction in the high and low reverse clutch hydraulic pressure. When it
detects any malfunction, it puts the system into fail-safe mode.

AT-44
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
A/T Interlock

If there is an A/T interlock judgment malfunction, the transmission is fixed in 2nd gear to make driving pos-
sible.
NOTE:
When the vehicle is driven fixed in 2nd gear, a turbine revolution sensor malfunction is displayed,
but this is not a turbine revolution sensor malfunction.

When the coupling pattern below is detected, the fail-safe action corresponding to the pattern is per-
formed.
A/T INTERLOCK COUPLING PATTERN TABLE

: NG X: OK
A/T 1st Engine Braking

When there is an A/T first gear engine brake judgment malfunction, the low coast brake solenoid is
switched “OFF” to avoid the engine brake operation.
Line Pressure Solenoid

The solenoid is switched “OFF” and the line pressure is set to the maximum hydraulic pressure to make
driving possible.
Torque Converter Clutch Solenoid

The solenoid is switched “OFF” to release the lock-up.
Low Coast Brake Solenoid

When a (electrical or functional) malfunction occurs, in order to make driving possible, the engine brake is
not applied in 1st and 2nd gear.
Input Clutch Solenoid

If a (electrical or functional) malfunction occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Direct Clutch Solenoid

If a (electrical or functional) malfunction occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Front Brake Solenoid

If a (electrical or functional) malfunction occurs with the solenoid “ON”, in order to make driving possible,
the A/T is held in 5th gear; if the solenoid is OFF, 4th gear.
High and Low Reverse Clutch Solenoid

If a (electrical or functional) malfunction occurs with the solenoid either “ON” or “OFF”, the transmission is
held in 4th gear to make driving possible.
Turbine Revolution Sensor 1 or 2

The control is the same as if there were no turbine revolution sensors, 5th gear is prohibited.
Gear positionATF pressure switch output
Fail-safe
functionClutch pressure output pattern after fail-safe func-
tion
SW3
(I/C)SW6
(HLR/
C)SW5
(D/C)SW1
(Fr/B)SW2
(LC/B)I/C HLR/C D/C Fr/B LC/B L/U
A/T inter-
lock cou-
pling pattern3rd – X X –
Held in
2nd gearOFF OFF ON OFF OFF OFF
4th – X X –
Held in
2nd gearOFF OFF ON OFF OFF OFF
5th X X – X
Held in
2nd gearOFF OFF ON OFF OFF OFF

TROUBLE DIAGNOSIS
AT-47
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
DIAGNOSTIC WORKSHEET
Information From Customer
KEY POINTS

WHAT..... Vehicle & A/T model

WHEN..... Date, Frequencies

WHERE..... Road conditions

HOW..... Operating conditions, Symptoms
Diagnostic Worksheet Chart
Customer name MR/MS Model & Year VIN
Trans. Model Engine Mileage
Malfunction Date Manuf. Date In Service Date
Frequency❏ Continuous❏ Intermittent ( times a day)
Symptoms❏ Vehicle does not move. (❏ Any position❏ Particular position)
❏ No up-shift (❏ 1st → 2nd❏ 2nd → 3rd❏ 3rd → 4th ❏ 4th → 5th)
❏ No down-shift (❏ 5th → 4th ❏ 4th → 3rd❏ 3rd → 2nd❏ 2nd → 1st)
❏ Lock-up malfunction
❏ Shift point too high or too low.
❏ Shift shock or slip (❏ N → D❏ Lock-up❏ Any drive position)
❏ Noise or vibration
❏ No kick down
❏ No pattern select
❏ Others
()
AT CHECK indicator lamp Blinks for about 8 seconds.
❏ Continuously lit❏ Not lit
Malfunction indicator lamp (MIL)❏ Continuously lit❏ Not lit
1❏ Read the item on “cautions concerning fail-safe and understand the customer's complaint.AT- 4 3
2❏ ATF inspection
AT- 5 8❏ Leak (Repair leak location.)
❏ Sta te
❏ Amount
3❏ Stall test and line pressure test
AT- 5 8
, AT-
59
❏ Stall test
❏ Torque converter one-way clutch
❏ Front brake
❏ High and low reverse clutch
❏ Low coast brake
❏ Forward brake
❏ Reverse brake
❏ Forward one-way clutch❏ 1st one-way clutch
❏ 3rd one-way clutch
❏ Engine
❏ Line pressure low
❏ Except for input clutch and direct
clutch, clutches and brakes OK
❏ Line pressure inspection - Suspected part:

AT-48
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
4❏ Perform all road tests and enter checks in required inspection items.AT-6 1
4-1.Check before engine is started
AT-6 2
❏ AT-191, "AT CHECK Indicator Lamp Does Not Come On" .
❏ Perform self-diagnostics Enter checks for detected items. AT- 9 3
❏ AT- 1 0 3 , "DTC U1000 CAN COMMUNICATION LINE"
❏ AT- 1 0 5 , "DTC P0615 START SIGNAL CIRCUIT"
❏ AT- 1 0 8 , "DTC P0700 TCM"
❏ AT- 1 0 9 , "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ AT- 11 2 , "DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)"
❏ AT- 11 5 , "DTC P0725 ENGINE SPEED SIGNAL"
❏ AT- 11 8 , "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ AT- 1 2 1 , "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ AT- 1 2 4 , "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ AT- 1 2 7 , "DTC P1702 TRANSMISSION CONTROL MODULE (RAM)"
❏ AT- 1 2 8 , "DTC P1703 TRANSMISSION CONTROL MODULE (ROM)"
❏ AT- 1 2 9 , "DTC P1705 THROTTLE POSITION SENSOR"
❏ AT- 1 3 1 , "DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT"
❏ AT- 1 3 4 , "DTC P1716 TURBINE REVOLUTION SENSOR"
❏ AT- 1 3 6 , "DTC P1721 VEHICLE SPEED SENSOR MTR"
❏ AT- 1 3 9 , "DTC P1730 A/T INTERLOCK"
❏ AT- 1 4 2 , "DTC P1731 A/T 1ST ENGINE BRAKING"
❏ AT- 1 4 5 , "DTC P1752 INPUT CLUTCH SOLENOID VALVE"
❏ AT- 1 4 8 , "DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT- 1 5 1 , "DTC P1757 FRONT BRAKE SOLENOID VALVE"
❏ AT- 1 5 4 , "DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION"
❏ AT- 1 5 7 , "DTC P1762 DIRECT CLUTCH SOLENOID VALVE"
❏ AT- 1 6 0 , "DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT- 1 6 3 , "DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE"
❏ AT- 1 6 6 , "DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION"
❏ AT- 1 6 9 , "DTC P1772 LOW COAST BRAKE SOLENOID VALVE"
❏ AT- 1 7 2 , "DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION"
❏ AT- 1 7 5 , "DTC P1841 ATF PRESSURE SWITCH 1"
❏ AT- 1 7 8 , "DTC P1843 ATF PRESSURE SWITCH 3"
❏ AT- 1 8 1 , "DTC P1845 ATF PRESSURE SWITCH 5"
❏ AT- 1 8 4 , "DTC P1846 ATF PRESSURE SWITCH 6"
4-2.Idle inspection
AT-6 2
❏ AT-192, "Engine Cannot Be Started In “P” or “N” Position"
❏ AT-193, "In “P” Position, Vehicle Moves When Pushed"
❏ AT-194, "In “N” Position, Vehicle Moves"
❏ AT-195, "Large Shock (“N” to “D” Position)"
❏ AT-198, "Vehicle Does Not Creep Backward In “R” Position"
❏ AT-201, "Vehicle Does Not Creep Forward In “D” Position"
4-3.Driving tests
AT-6 3
Part 1
❏ AT-203, "
Vehicle Cannot Be Started From D1"
❏ AT-206, "A/T Does Not Shift: D1 → D2"
❏ AT-208, "A/T Does Not Shift: D2 → D3"
❏ AT-210, "A/T Does Not Shift: D3 → D4"
❏ AT-213, "A/T Does Not Shift: D4 → D5"
❏ AT-215, "A/T Does Not Perform Lock-up"
❏ AT-217, "A/T Does Not Hold Lock-up Condition"
❏ AT-219, "Lock-up Is Not Released"
❏ AT-220, "Engine Speed Does Not Return to Idle"

TROUBLE DIAGNOSIS
AT-49
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
44-3Part 2
AT- 6 5
❏ AT-203, "Vehicle Cannot Be Started From D1"
❏ AT-206, "A/T Does Not Shift: D1 → D2"
❏ AT-208, "A/T Does Not Shift: D2 → D3"
❏ AT-210, "A/T Does Not Shift: D3 → D4"
Part 3
AT- 6 6
❏ AT-221, "A/T Does Not Shift: 5th gear → 4th gear"
❏ AT-224, "A/T Does Not Shift: 4th gear → 3rd gear"
❏ AT-225, "A/T Does Not Shift: 3rd gear → 2nd gear"
❏ AT-227, "A/T Does Not Shift: 2nd gear → 1st gear"
❏ AT-230, "Vehicle Does Not Decelerate By Engine Brake"
❏ Perform self-diagnostics Enter checks for detected items. AT- 9 3
❏ AT-103, "DTC U1000 CAN COMMUNICATION LINE"
❏ AT-105, "DTC P0615 START SIGNAL CIRCUIT"
❏ AT-108, "DTC P0700 TCM"
❏ AT-109, "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ AT-112, "DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)"
❏ AT-115, "DTC P0725 ENGINE SPEED SIGNAL"
❏ AT-118, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ AT-121, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ AT-124, "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ AT-127, "DTC P1702 TRANSMISSION CONTROL MODULE (RAM)"
❏ AT-128, "DTC P1703 TRANSMISSION CONTROL MODULE (ROM)"
❏ AT-129, "DTC P1705 THROTTLE POSITION SENSOR"
❏ AT-131, "DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT"
❏ AT-134, "DTC P1716 TURBINE REVOLUTION SENSOR"
❏ AT-136, "DTC P1721 VEHICLE SPEED SENSOR MTR"
❏ AT-139, "DTC P1730 A/T INTERLOCK"
❏ AT-142, "DTC P1731 A/T 1ST ENGINE BRAKING"
❏ AT-145, "DTC P1752 INPUT CLUTCH SOLENOID VALVE"
❏ AT-148, "DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-151, "DTC P1757 FRONT BRAKE SOLENOID VALVE"
❏ AT-154, "DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION"
❏ AT-157, "DTC P1762 DIRECT CLUTCH SOLENOID VALVE"
❏ AT-160, "DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-163, "DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE"
❏ AT-166, "DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION"
❏ AT-169, "DTC P1772 LOW COAST BRAKE SOLENOID VALVE"
❏ AT-172, "DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION"
❏ AT-175, "DTC P1841 ATF PRESSURE SWITCH 1"
❏ AT-178, "DTC P1843 ATF PRESSURE SWITCH 3"
❏ AT-181, "DTC P1845 ATF PRESSURE SWITCH 5"
❏ AT-184, "DTC P1846 ATF PRESSURE SWITCH 6"
5❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunction
parts.
6❏ Perform all road tests and enter the checks again for the required items.AT- 6 1
7❏ For any remaining NG items, perform the “diagnostics procedure” and repair or replace the malfunction parts.
See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection proce-
dures.)AT- 6 8
8❏ Erase the results of the self-diagnostics from the TCM.AT- 4 0

TROUBLE DIAGNOSIS
AT-59
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
CAUTION:
Run the engine at idle for at least one minute.
Judgement of Stall Test
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value position
LINE PRESSURE TEST
Line Pressure Test Port
Line Pressure Test Procedure
1. Inspect the amount of engine oil and replenish if necessary.
2. Drive the car for about 10 minutes to warm it up so that the ATF reaches in range of 50 to 80°C (122 to
176°F), then inspect the amount of ATF and replenish if necessary.
NOTE:
The automatic fluid temperature rises in range of 50 to 80°C (122 to 176°F) during 10 minutes of
driving.Stall speed: 2,500 - 2,800 rpm
Selector lever position
Expected problem location
DR
Stall rotation HO

Forward brake

Forward one-way clutch

1st one-way clutch

3rd one-way clutch
OH

Reverse brake
LL

Engine and torque converter one-way clutch
HH

Line pressure low
Does not shift-up D position 1 → 2 Slipping in 2nd, 3rd, 4th gears Direct clutch slippage
Does not shift-up D position 2 → 3 Slipping in 3rd, 4th, 5th gears High & low reverse clutch slippage
Does not shift-up D position 3 → 4 Slipping in 4th, 5th gears Input clutch slippage
Does not shift-up D position 4 → 5 Slipping in 5th gear Front brake slippage
SCIA1291E

AT-68
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
Symptom ChartUCS002D6

The diagnostics item numbers show the sequence for inspection. Inspect in order from item 1.

Overhaul and inspect inside the A/T only if A/T fluid condition is NG. Refer to AT-58, "Fluid Condi-
tion Check" .
No. Items Symptom Condition Diagnostic ItemReference
page
1
Shift
ShockLarge shock. (“N” →“
D” position)
Refer to AT-195,
"Large Shock (“N” to
“D” Position)" .ON vehicle1. Engine idle speedEC-32
2. Engine speed signalAT - 11 5
3. Accelerator pedal position sensorAT- 1 2 9
4. Control cable adjustmentAT- 2 3 4
5. ATF temperature sensorAT- 1 3 1
6. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1
7. CAN communication lineAT- 1 0 3
8. Fluid level and stateAT-5 8
9. Line pressure testAT-5 9
10. Control valve with TCMAT- 2 4 2
OFF vehicle11. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8 , AT- 1 9
.)AT- 2 7 3
2Shock is too large
when changing D1 →
D
2 .ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
4. CAN communication lineAT- 1 0 3
5. Engine speed signalAT - 11 5
6. Turbine revolution sensorAT- 1 3 4
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
8. Fluid level and stateAT-5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle 10. Direct clutchAT- 3 0 7
3Shock is too large
when changing D2 →
D
3 .ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 8 4,
AT- 1 6 3
4. CAN communication lineAT- 1 0 3
5. Engine speed signalAT - 11 5
6. Turbine revolution sensorAT- 1 3 4
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
8. Fluid level and stateAT-5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle 10. High and low reverse clutchAT- 3 0 5

TROUBLE DIAGNOSIS
AT-69
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
4
Shift
ShockShock is too large
when changing D3 →
D
4 .ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 7 8,
AT- 1 4 5
4. CAN communication lineAT- 1 0 3
5. Engine speed signalAT- 11 5
6. Turbine revolution sensorAT- 1 3 4
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
8. Fluid level and stateAT- 5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle 10. Input clutchAT- 2 9 5
5Shock is too large
when changing D4 →
D
5 .ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1

4. CAN communication lineAT- 1 0 3
5. Engine speed signalAT- 11 5
6. Turbine revolution sensorAT- 1 3 4
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
8. Fluid level and stateAT- 5 8
9. Control valve with TCMAT- 2 4 1
OFF vehicle10. Front brake (brake band)AT- 2 6 111. Input clutchAT- 2 9 5
6Shock is too large for
downshift when accel-
erator pedal is
pressed.ON vehicle1. Accelerator pedal position sensorAT- 1 2 9
2. Control cable adjustmentAT- 2 3 4
3. CAN communication lineAT- 1 0 3
4. Engine speed signalAT- 11 5
5. Turbine revolution sensorAT- 1 3 4
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
7. Fluid level and stateAT- 5 8
8. Control valve with TCMAT- 2 4 1
OFF vehicle9. Front brake (brake band)AT- 2 6 110. Input clutchAT- 2 9 5
11. High and low reverse clutchAT- 3 0 5
12. Direct clutchAT- 3 0 7
No. Items Symptom Condition Diagnostic ItemReference
page