combination meter INFINITI QX56 2004 Factory Owner's Guide

DI-2Revision: August 20072004 QX56 CAN Communication System Description .............. 45
Wiring Diagram — CHIME — ................................. 46
Terminals and Reference Value for BCM ................ 48
Terminals and Reference Value for Combination
Meter ...................................................................... 49
How to Proceed With Trouble Diagnosis ................ 49
Preliminary Check .................................................. 49
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT ............................................. 49
CONSULT-II Function (BCM) .................................. 51
CONSULT-II BASIC OPERATION PROCEDURE
... 51
DATA MONITOR .................................................. 52
ACTIVE TEST ..................................................... 52
SELF-DIAGNOSTIC RESULTS ........................... 52
All Warning Chimes Do Not Operate ...................... 53
Key Warning Chime and Light Warning Chime Do
Not Operate (Seat Belt Warning Chime Does Oper-
ate) ......................................................................... 53
Key Warning Chime Does Not Operate .................. 54
Light Warning Chime Does Not Operate ................ 56
Seat Belt Warning Chime Does Not Operate ......... 57
REAR SONAR SYSTEM ........................................... 59
Component Parts and Harness Connector Location ... 59
System Description ................................................. 60
FUNCTION .......................................................... 60
REAR SONAR SYSTEM OFF SWITCH .............. 60
SONAR BUZZER ................................................ 60
REAR SONAR SENSOR ..................................... 61
Wiring Diagram — SONAR — ................................ 62
Terminals And Reference Value For Sonar Control
Unit ......................................................................... 64
How to Proceed With Trouble Diagnosis ................ 64
Pre-diagnosis Inspection ........................................ 65
SENSOR STATUS CHECK ................................. 65
Self-diagnosis Function .......................................... 65
ENTERING DIAGNOSTICS MODE .................... 65
REQUESTING NUMBER OF FAULT CODES
MODE .................................................................. 65
REQUESTING FAULT CODES MODE ............... 66
IDLING OR CLEARING FAULT CODES MODE ... 66
Preliminary Check .................................................. 67INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT .............................................67
Symptom Chart .......................................................68
Component Inspection ............................................69
SONAR BUZZER .................................................69
REAR SONAR SYSTEM OFF SWITCH ..............69
REAR SONAR SYSTEM OFF INDICATOR .........69
Removal and Installation of Rear Sonar System ....69
REAR SONAR SENSORS ...................................69
SONAR CONTROL UNIT ....................................69
CLOCK ......................................................................70
Wiring Diagram — CLOCK — .................................70
Removal and Installation of Clock ...........................71
REMOVAL ............................................................71
INSTALLATION ....................................................71
REAR VIEW MONITOR .............................................72
System Description .................................................72
POWER SUPPLY AND GROUND .......................72
AV COMMUNICATION LINE ...............................72
REAR VIEW CAMERA OPERATION ..................72
Component Parts and Harness Connector Location ...73
Schematic ...............................................................74
Wiring Diagram — R/VIEW — ................................75
Terminals and Reference Value for Rear View Cam-
era Control Unit .......................................................78
CONSULT-II Function (REARVIEW CAMERA) ......79
CONSULT-II BASIC OPERATION .......................79
WORK SUPPORT ...............................................80
DATA MONITOR ..................................................80
Side Distance Guideline Correction ........................81
SIDE DISTANCE GUIDELINE CORRECTION
PROCEDURE ......................................................81
Power Supply and Ground Circuit Inspection .........83
Rear View Is Not Displayed With The A/T Selector
Lever In R Position ..................................................84
Removal and Installation of Rear View Camera Con-
trol Unit ....................................................................88
REMOVAL ............................................................88
INSTALLATION ....................................................88
Removal and Installation of Rear View Camera .....88
REMOVAL ............................................................88
INSTALLATION ....................................................88

COMBINATION METERS
DI-5
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
COMBINATION METERSPFP:24814
System DescriptionEKS007DL
UNIFIED METER CONTROL UNIT

Speedometer, odometer, tachometer, fuel gauge, oil pressure gauge, voltage meter, A/T temperature
gauge, and water temperature gauge are controlled by the unified meter control unit, which is built into the
combination meter.

Warning indicators are controlled by signals drawn from the CAN communication system, BCM (body con-
trol module), and components connected directly to the combination meter.

Digital meter is adopted for odometer/trip meters*, as well as the A/T position indicator display.
*The record of the odometer is kept even if the battery cable is disconnected.

Odometer/trip meters and A/T indicator segments can be checked in diagnosis mode.

Meters/gauges can be checked in diagnosis mode.
Illumination control
The unified meter control unit outputs the speedometer, odometer/trip meters, tachometer, oil pressure gauge,
voltage meter, A/T indicator, A/T temperature gauge, fuel and temperature gauge lighting when the ignition
switch is turned on. When the lighting switch is turned on, the illumination control switch can be used to adjust
the brightness of the combination meter illumination and the odometer/trip meters and meter illumination.
When the ignition switch is turned from the OFF to the ON position, the combination meter dial lighting will
remain off for 0.7 seconds. For additional combination meter illumination control information, refer to LT-152,
"System Description" .

DI-6
COMBINATION METERS
Revision: August 20072004 QX56
POWER SUPPLY AND GROUND CIRCUIT
Power is supplied at all times

through 10A fuse [No.19, located in the fuse block (J/B)]

to combination meter terminal 8.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No.14, located in the fuse block (J/B)]

to combination meter terminal 24.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No.4, located in the fuse block (J/B)]

to combination meter terminal 1.
Ground is supplied

to combination meter terminal 17

through body grounds M57, M61 and M79.
WATER TEMPERATURE GAUGE
The water temperature gauge indicates the engine coolant temperature.
ECM provides an engine coolant temperature signal to combination meter via CAN communication lines.
ENGINE OIL PRESSURE GAUGE
The engine oil pressure gauge indicates the engine oil pressure.
The engine oil pressure gauge is regulated by the unified meter control unit and input from the oil pressure
sensor.
A/T OIL TEMPERATURE GAUGE
The A/T oil temperature gauge indicates the A/T fluid temperature.
TCM (transmission control module) provides an A/T fluid temperature signal to combination meter via CAN
communication lines.
V O LTA G E G A U G E
The voltage gauge indicates the battery/charging system voltage.
The voltage gauge is regulated by the unified meter control unit.
TACHOMETER
The tachometer indicates engine speed in revolutions per minute (rpm).
ECM provides an engine speed signal to combination meter via CAN communication lines.
FUEL GAUGE
The fuel gauge indicates the approximate fuel level in the fuel tank.
The fuel gauge is regulated by the unified meter control unit and a variable resistor signal supplied

to combination meter terminal 15.

through fuel level sensor unit and fuel pump terminal 2

through fuel level sensor unit and fuel pump terminal 5

from combination meter terminal 16
SPEEDOMETER
ABS actuator and electric unit (control unit) provides a vehicle speed signal to the combination meter via CAN
communication lines.
CAN COMMUNICATION SYSTEM DESCRIPTION
Refer to LAN-5, "CAN COMMUNICATION" .

COMBINATION METERS
DI-7
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
Component Parts and Harness Connector LocationEKS007DM
WKIA4145E

DI-8
COMBINATION METERS
Revision: August 20072004 QX56
Combination MeterEKS007DN
CHECK
WKIA4146E

COMBINATION METERS
DI-9
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
Circuit DiagramEKS007DO
WKWA3051E

DI-10
COMBINATION METERS
Revision: August 20072004 QX56
Wiring Diagram — METER —EKS007DP
WKWA3052E

COMBINATION METERS
DI-11
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
WKWA3053E

DI-12
COMBINATION METERS
Revision: August 20072004 QX56
Terminals and Reference Value for Combination MeterEKS007DQ
Te r m i n a l
No.Wire
colorItemCondition
Reference value (V)
(Approx.) Ignition
switchOperation or condition
1OIgnition switch ACC or
ONACC — Battery voltage
8 Y/R Battery power supply OFF — Battery voltage
11 W C A N - H — — —
12 R CAN-L — — —
15 Y/L Fuel level sensor signal — —Refer to DI-22, "
Fuel Level Sensor
Unit Inspection" .
16 B/PFuel level sensor and oil
pressure sensor groundON — 0V
17 B Ground OFF — 0V
18 BR Illumination control switch — Lighting switch ONRefer to LT-153, "
ILLUMINATION
OPERATION BY LIGHTING
SWITCH" .
20 YOil pressure sensor sig-
nalON — 0 - 5V
22 GR/LOil pressure sensor refer-
ence voltageON — 5V
24 O/LIgnition switch ON or
STARTON — Battery voltage

COMBINATION METERS
DI-13
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
Meter/Gauge Operation and Odo/Trip MeterEKS007DR
SELF-DIAGNOSIS FUNCTION
The following items can be checked during Combination Meter Self-Diagnosis Mode.

Gauge sweep and present gauge values.

Illuminates all odometer, fuel, and engine temperature segments.

Illuminates all micro controlled lamps/LED's regardless of switch configuration.

Displays estimated present battery voltage.

Displays seat belt buckle switch LH status.
HOW TO INITIATE COMBINATION METER SELF- DIAGNOSIS MODE
NOTE:
Once entered, Combination Meter Self-Diagnosis Mode will function with the ignition switch in ON or START.
Combination Meter Self-Diagnosis Mode will exit upon turning the ignition switch to OFF or ACC.
To initiate Combination Meter Self-Diagnosis Mode, refer to the following procedure.
1. Turn the ignition switch ON, while holding the odometer/trip meter switch for 5 - 8 seconds.
NOTE:
If the diagnosis function is activated the odometer/trip meter will display tESt.
COMBINATION METER SELF-DIAGNOSIS MODE FUNCTIONS
To interpret Combination Meter Self-Diagnosis Mode functions, refer to the following table.
Event Odometer Display Description of Test/Data Notes:
Odometer/trip meter A/B
switch held from 5 to 8
seconds (or until
released)tESt Initiating self-diagnosis mode
Odometer/trip meter A/B
switch engaged and
released = next test
requestedrXXXX, FAILReturn to normal opera-
tion of all lamps/LEDs and
displays hex ROM rev. If
a ROM checksum fault
exists, display alternates
between "r XXXX" and
"FAIL".
Next test requested nrXXXXDisplays hex ROM rev as
stored in NVM.
Next test requested GAGEPerforms sweep of all
gauges, then displays
present gauge values.
Performs checksum tests
on ROM and EE.Gauges sweep within 10 sec-
onds
Next test requested (All segments illuminated)Lights all odometer/trip
meter, fuel, and engine
temperature display seg-
ments.Initiating self-diagnosis mode
complete
Next test requested bulbIlluminates all micro-con-
trolled lamps/LEDs
regardless of SW configu-
ration.
Next test requested EE XX, FAILHex EE level. If EE
checksum fault exists,
display alternates
between "EE XX" and
"FAIL".
Next test requested dtXXXXHex coding of final manu-
facturing test date.