INFINITI QX56 2004 Factory Workshop Manual

ACS-32
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: August 20072004 QX56
Self-Diagnostic FunctionEKS007PI
WITH CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop vehicle, turn ignition switch OFF, then connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3. With engine started, touch “START”, “ICC”, “SELF-DIAG RESULTS” on CONSULT-II screen in this order.
CAUTION:
If “ICC” cannot be shown after several attempts, the ICC unit may be malfunctioning and should
be replaced. Refer to GI-39, "
CONSULT-II Data Link Connector (DLC) Circuit" .
4. Self-diagnostic result appears on screen. If “NO DTC ···” is shown, check ICC warning lamp. If any mal-
function is indicated, GO TO step 5.
5. Refer to ACS-36, "
Diagnostic Trouble Code (DTC) Chart" , perform appropriate check, and repair or
replace malfunctioning part as necessary.
6. Turn ignition switch OFF.
7. Start engine and touch “START”, “ICC”, “SELF-DIAG RESULT”, and “ERASE” on CONSULT-II.
CAUTION:
DTC of an existing malfunction will not erase. If the memory does not erase, go to step 5.
8. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
WITHOUT CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop the vehicle to start the self-diagnosis.
3. Turn ignition switch OFF.
4. Turn ignition switch ON, and wait 5 seconds. Press ACCEL/RES
switch 5 times, and then press COAST/SET switch 5 times all
within 5 seconds to start self-diagnosis.
CAUTION:

Do not start the engine.

Do not press the ICC ON/OFF switch ON.

When operation above is not completed within the 5 to 10
second window, DTC will not be displayed.

If self-diagnosis mode cannot be started after several
attempts, the ICC unit may be malfunctioning and should be
replaced. Refer to ACS-34, "
SELF-DIAGNOSIS BY ICC SYS-
TEM DISPLAY WILL NOT RUN" .
5. When self-diagnosis mode is started, DTCs are shown on set vehicle speed indicator.
PKIA0363J
WKIA1921E

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-33
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
CAUTION:

DTC will disappear after 5 minutes.

When multiple malfunctions are detected, a maximum of 3 code numbers can be stored; the lat-
est malfunction will be displayed first.
6. Check ACS-36, "
Diagnostic Trouble Code (DTC) Chart" , and repair or replace if necessary.
7. After repair, erase DTC stored in the ICC unit. Refer to ACS-33, "
Self-Diagnostic Erasing Method"
8. DTC 55 will be shown.
9. Turn ignition switch OFF to exit the diagnosis.
10. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
Self-Diagnostic Erasing Method
1. Stop the vehicle and turn the ignition switch OFF.
2. Turn ignition switch ON and start self-diagnosis.
3. During self-diagnosis mode, press CANCEL switch 5 times, and DISTANCE switch 5 times within a 10
second time period.
CAUTION:

Switch inputs must be received within a 10 second time period.

When operation is not completed within 10 seconds start again from step 1.
4. DTC 55 will be shown.
CAUTION:
DTC of an existing malfunction will not be erased.
5. Turn ignition switch OFF to exit the diagnosis.
6. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC system
warning lamp (orange) does not illuminate.
WKIA1922E

ACS-34
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: August 20072004 QX56
SELF-DIAGNOSIS BY ICC SYSTEM DISPLAY WILL NOT RUN
Self Diagnosis Will Not Run
1. CHECK ICC SYSTEM DISPLAY

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> GO TO 2.
NO >> GO TO 5.
2. CHECK SELF-DIAGNOSIS

Disconnect ECM connectors, and check for damaged, bent or loose terminals. Securely connect them
again.

Can self-diagnosis for ICC system be performed?
YES or NO
YES >> Inspection End.
NO >> GO TO 3.
WKIA1985E
Component Failure Specific causes
ICC unit power supply malfunction No voltage supply from ignition switch Fuse blown
Harness open
Harness shorted
Ground cable not connected Harness open
Harness shorted
ICC steering switch malfunction No signal transmitted Harness open
Harness shorted
Spiral cable open
Spiral cable shorted
Switch or ECM malfunction
CAN communication system malfunction Signal not transmitted Harness open
Harness shorted
CAN communication outside the stan-
dard
Combination meter system malfunction Indication not possible Indicator malfunction
Indicator segments disappear
ICC unit malfunction Internal malfunction ICC unit

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-35
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
3. CHECK ICC STEERING SWITCH

Check ICC steering switch. Refer to ACS-58, "ICC Steering Switch" .
OK or NG
OK >> GO TO 4.
NG >> Replace ICC steering switch. Refer to ACS-59, "
ICC Steering Switch"
4. CHECK HARNESS BETWEEN ECM AND ICC STEERING SWITCH

Check harness and spiral cable between ECM and ICC steering switch for open or short circuit.
OK or NG
OK >> GO TO 6
NG >> Repair or replace harness or spiral cable between ECM and ICC steering switch.
5. CHECK POWER SUPPLY FOR ICC UNIT

Check ICC unit power supply, and repair if necessary.

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> Perform self-diagnosis again.
NO >> GO TO 6.
6. CHECK CONNECTOR FOR ICC UNIT

Disconnect ICC unit connectors, and check terminals for bends and looseness. Securely connect them
again.

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> Perform self-diagnosis again.
NO >> GO TO 7.
7. CHECK CAN COMMUNICATION

Perform self-diagnosis with CONSULT-II, and check CAN communication system for malfunction.
OK or NG
OK >> Replace combination meter. Refer to IP-13, "Combination Meter"
NG >> CAN communication inspection. Refer to ACS-38, "DTC 20 CAN COMM CIRCUIT" .

ACS-36
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: August 20072004 QX56
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMSPFP:00000
Diagnostic Trouble Code (DTC) ChartEKS007X2
×:Applicable
DTC
No.CONSULT-II screen termsICC sys-
tem
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Vehicle-
to-vehi-
cle dis-
tance
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake
assist
(with pre-
view
function)
11 CONTROL UNIT××××

ICC unit internal malfunctionACS-37
12 VDC CONTROL UNIT××××

VDC malfunction

Brake booster signal harness is
open or shortedACS-37
20 CAN COMM CIRCUIT××××
ICC unit detected CAN communi-
cation malfunctionACS-38
31 POWER SUPPLY CIR1××××
ICC unit power supply voltage is
excessively low (less than 8V)ACS-38
34 POWER SUPPLY CIR2××××
ICC unit power supply voltage is
excessively high.ACS-38
41 VHCL SPEED SE CIRC××××

Wheel sensor malfunction

ABS actuator and electric unit
(control unit) malfunction

AT vehicle speed sensor mal-
function

TCM malfunctionACS-39
43 VDC/TCS/ABS CIRC××××
VDC/TCS/ABS system malfunc-
tionACS-39
45 BRAKE SW/ STOP L SW××××

ICC brake switch or stop lamp
switch harness is open or shorted

ICC brake switch or stop lamp
switch is stuck to OFF

ICC brake switch or stop lamp
switch is stuck to ONACS-40
46 OPERATION SW CIRC×××

ICC steering switch harness or
spiral cable is open or shorted

ICC steering switch malfunctionACS-41
74 LASER BEAM OFF CNTR×× ×
Laser beam of ICC sensor is off
the aiming pointACS-42
90 STOP LAMP RLY FIX×× ×
Normally open terminal of stop
lamp relay is stuckACS-43
92 ECM CIRCUIT××××

ECM malfunction

Accelerator pedal position sensor
malfunction

ICC unit malfunctionACS-47
96 NP RANGE×××

Park/neutral position switch har-
ness is open or shorted

Park/neutral position switch mal-
function

TCM malfunctionACS-48
97 AT CIRCUIT××
TCM malfunctionACS-48

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-37
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
DTC 11 CONTROL UNITEKS007X3
1. DIAGNOSTIC CHECK
1. Are any items other than “DTC 11 CONTROL UNIT” indicated on self-diagnosis display?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> Replace ICC unit. Refer to ACS-59, "
ICC Unit" . Erase DTC and perform ICC system running
test. Then perform self-diagnosis of ICC system again.
DTC 12 VDC CONTROL UNITEKS008DH
1. DIAGNOSIS CHECK
With CONSULT-II

Perform self-diagnosis of ABS actuator and electric unit (control unit). Is malfunction indicated?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then per-
form self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK CONNECTOR ICC UNIT AND ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
1. Turn ignition switch OFF.
2. Disconnect connectors of ICC unit and ABS actuator and electric unit (control unit), and connect them
securely again. Then erase DTC. Then, perform self-diagnosis of ICC system again.
OK or NG
OK >> Poor connector connection. Check connector housing for disconnected, loose, bent and col-
lapsed terminals. If any malfunction is detected, repair applicable part. After repair, erase DTC
and perform ICC system running test. Then perform self-diagnosis of ICC system again.
NG >> GO TO 3.
98 GEAR POSITION××

TCM malfunction

AT turbine revolution sensor mal-
function

AT vehicle speed sensor mal-
functionACS-49
102 LASER STAIN×× ×
ICC sensor body window has
contaminationACS-49
103 LASER SENSOR FAIL×× ×
ICC sensor internal malfunctionACS-50
104 LASER AIMING INCMP×× ×
Laser beam aiming of ICC sensor
is not adjustedACS-50
107 LASER COMM FAIL×× ×

CAN data received by ICC sen-
sor is strange (from ICC unit,
combination meter or ECM)ACS-51
109 LASER HIGH TEMP×× ×
Temperature around ICC sensor
is excessively highACS-51
DTC
No.CONSULT-II screen termsICC sys-
tem
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Vehicle-
to-vehi-
cle dis-
tance
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake
assist
(with pre-
view
function)

ACS-38
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: August 20072004 QX56
3. CHECK HARNESS BETWEEN ICC UNIT AND ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)
1. Turn ignition switch OFF.
2. Disconnect connectors of ICC unit and ABS actuator and elec-
tric unit (control unit).
3. Check continuity between ICC unit harness connector B13 ter-
minal 10 (V/R) and ABS actuator and electric unit (control unit)
connector E125 terminal 7 (V/R).
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase
DTC and perform ICC system running test. Then per-
form self-diagnosis of ICC system again.
NG >>

Repair harness between ICC unit and ABS actuator and electric unit (control unit).

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
DTC 20 CAN COMM CIRCUITEKS007X4
1. CHECK CAN COMMUNICATION
With CONSULT-II
1. Perform self-diagnosis.
2. Print self-diagnostic result.
>> After printing self-diagnostic result, go to “CAN system”. Refer to LAN-3, "
Precautions When
Using CONSULT-II" .
DTC 31 POWER SUPPLY CIR 1, DTC 34 POWER SUPPLY CIR 2EKS007X5
1. CHECK ICC UNIT CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector and connect it securely again. Then erase DTC. Then perform self-diagno-
sis of ICC system again.
OK or NG
OK >> GO TO 2.
NG >>

Poor connector connection.

Check connector. (Check connector housing for disconnected, loose, bent, and collapsed ter-
minals. If any malfunction is detected, repair applicable part.) After repair, erase DTC, and per-
form ICC running test. Then perform self-diagnosis of ICC system again.
2. CHECK POWER SUPPLY CIRCUIT FOR ICC UNIT
1. Turn ignition switch ON.
2. Check voltage between ICC unit harness connector B17 termi-
nal 33 (R/B), 42 (R/B) and ground.
OK or NG
OK >> GO TO 3.
NG >>

Repair ICC unit power supply harness.

After repair, erase DTC and perform ICC system run-
ning test. Then, perform self-diagnosis of ICC system
again. Continuity should exist.
WKIA2042E
Battery voltage should exist.
SKIA11 73 E

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-39
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
3. CHECK GROUND CIRCUIT FOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connectors.
3. Check continuity between ICC unit harness connector B13 ter-
minal 19 (B), 20 (B), B17 terminal 46 (B) and ground.
OK or NG
OK >> Replace ICC unit, Refer to ACS-59, "ICC Unit" . Erase
DTC, and perform ICC system running test. Then per-
form self-diagnosis of ICC system again.
NG >>

Repair ICC unit ground harness.

After repair, erase DTC and perform ICC system running test. Then perform self-diagnosis of
ICC system again.
DTC 41 VHCL SPEED SE CIRCEKS007X6
1. PERFORM ICC UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis. Is “DTC 43 VDC/TCS/ABS CIRC” or “DTC 20 CAN COMM CIRCUIT” indicated in
self-diagnosis item display?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK AT VEHICLE SPEED SENSOR
With CONSULT-II

With data monitor, check “VHCL SPD AT”.
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform ICC system running
test. Then perform self-diagnosis of ICC system again.
NG >>

Check TCM.

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
DTC 43 VDC/TCS/ABS CIRCEKS007X7
1. DIAGNOSIS CHECK 1
With CONSULT-II

Perform self-diagnosis. Is “CAN COMM CIRCUIT” indicated?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> GO TO 2.
2. DIAGNOSIS CHECK 2
With CONSULT-II

Perform self-diagnosis of ABS actuator and electric unit (control unit). Is malfunction indicated?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> Replace ICC unit. Refer to ACS-59, "
ICC Unit" . Erase DTC and perform ICC system running
test. Then perform self-diagnosis of ICC system again. Continuity should exist.
SKIA6650E

ACS-40
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: August 20072004 QX56
DTC 45 BRAKE SW/STOP L SWEKS007X8
1. CHECK CONNECTORS FOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connectors, and connect them securely again. Then erase DTC. Then, perform self-
diagnosis of ICC system again.
OK or NG
OK >>
Poor connector connection.

Check connectors. (Check connectors housing for disconnected, loose, bent, and collapsed
terminals. If any malfunction is detected, repair applicable part.) After repair, erase DTC, and
perform ICC system running test. Then perform self-diagnosis of ICC system again.
NG >> GO TO 2.
2. CHECK STOP LAMP SWITCH AND ICC BRAKE SWITCH
With CONSULT-II

With data monitor, check if “STOP LAMP SW” and “BRAKE SW” are operating normally.
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform ICC system running
test. Then perform self-diagnosis of ICC system again.
NG >>

BRAKE SW: GO TO 3.

STOP LAMP SW: GO TO 5.
3. ICC BRAKE SWITCH INSTALLATION AND ADJUSTMENT INSPECTION

Check ICC brake switch for proper installation and adjust if necessary. Refer to BR-6, "BRAKE PEDAL" .
OK or NG
OK >> GO TO 4.
NG >> After adjustment, erase DTC and perform ICC system running test. Then perform self-diagnosis
of ICC system again.
4. CHECK ICC BRAKE SWITCH

Check ICC brake switch. Refer to ACS-58, "ICC Brake Switch and Stop Lamp Switch" .
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform ICC system running
test. Then perform self-diagnosis of ICC system again.
NG >> Replace ICC brake switch. Erase DTC and perform ICC system running test. Then perform self-
diagnosis of ICC system again.
5. CHECK STOP LAMP ILLUMINATION

Check stop lamp illumination.
OK or NG
OK >> GO TO 6.
NG >>

Check stop lamp circuit.

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-41
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
6. CHECK ICC BRAKE HOLD RELAY
1. Turn ignition switch OFF.
2. Remove ICC brake hold relay.
3. Check continuity between terminals of ICC brake hold relay.
OK or NG
OK >> GO TO 7.
NG >> Replace ICC brake hold relay. Erase DTC and perform
ICC system running test. Then perform self-diagnosis of
ICC system again.
7. CHECK ICC BRAKE HOLD RELAY CIRCUIT
1. Disconnect connectors of ICC unit and stop lamp switch.
2. Check continuity between ICC unit harness connector B17 ter-
minal 38 (R/G) and ICC brake hold relay harness connector
E134 terminal 7 (R/G).
3. Check continuity between ICC unit harness connector B17 ter-
minal 38 (R/G) and stop lamp switch harness connector E38 ter-
minal 4 (R/G).
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase
DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
NG >>

Repair harness between ICC unit and ICC brake hold relay or stop lamp switch.

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
DTC 46 OPERATION SW CIRCEKS007X9
1. CHECK ECM CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect ECM connector, and connect it securely again. Then erase DTC. Then, perform self-diagnosis
of ICC system again.
OK or NG
OK >>
Poor connector connection.

Check connector. (Check connector housing for disconnected, loose, bent, and collapsed ter-
minals. If any malfunction is detected, repair applicable part.) After repair, erase DTC, and per-
form ICC system running test. Then perform self-diagnosis of ICC system again.
NG >> GO TO 2.
2. CHECK ICC STEERING SWITCH

Check ICC steering switch. Refer to ACS-58, "ICC Steering Switch" .
OK or NG
OK >> GO TO 3.
NG >> Replace ICC steering switch assembly. Refer to ACS-59, "
ICC Steering Switch" . Erase DTC and
perform ICC system running test. Then perform self-diagnosis of ICC system again. 7 - 6 Continuity should not exist.
4 - 3 Continuity should exist.
SKIA6651E
Continuity should exist.
Continuity should exist.
WKIA3403E