transfer INFINITI QX56 2004 Factory Manual Online

TF-78
SHIFT ACTUATOR
Revision: August 20072004 QX56
4. CHECK INPUT SIGNAL
With CONSULT-II
1. Start engine (idling).
2. Select “SELF-DIAG RESULTS” in Select Diag Mode.
3. Read out self-diagnostic result.
OK or NG
OK >> GO TO 7.
NG >> GO TO 6.
5. CHECK INPUT SIGNAL
Without CONSULT-II
1. Start engine (idling).
2. Check voltage between transfer control unit harness connector
E143 terminal 33 (R/L) [or 42 (P/G)] and ground while 4WD shift
switch is set from 4H to 4LO (or from 4LO to 4H).
3. Result
OK or NG
OK >> GO TO 7.
NG >> GO TO 6.
SMT826D
SMT978D
Terminal ConditionVo l ta g e
(Approx.)
33While actuator is
operating for 4H to
4LOBattery voltage
Actuator does not
operate0V
42While actuator is
operating for 4LO to
4HBattery voltage
Actuator does not
operate0V
SMT828D

SHIFT ACTUATOR
TF-79
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
6. CHECK HARNESS CONTINUITY BETWEEN TRANSFER CONTROL UNIT AND TRANSFER CON-
TROL DEVICE
OK or NG
OK >> GO TO 7.
NG >> Repair and replace harness connector between transfer control unit and transfer control device.
7. PERFORM SELF-DIAGNOSIS AGAIN
After driving for a while, perform self-diagnosis again.
Refer to TF-27, "
Trouble Diagnosis without CONSULT-II" .
OK or NG
OK >> Inspection End.
NG >> 1. Perform transfer control unit/output signal inspection. Refer to TF-55, "
TRANSFER CONTROL
UNIT INSPECTION TABLE" .
2. If NG, recheck transfer control unit pin terminals for damage or loose connection with harness
connector.

TF-80
SHIFT ACTUATOR POSITION SWITCH
Revision: August 20072004 QX56
SHIFT ACTUATOR POSITION SWITCHPFP:00000
Diagnostic ProcedureEDS0018C
1. SHIFT ACTUATOR POSITION SWITCH
Refer to TF-97, "
ACTUATOR AND ACTUATOR POSITION SWITCH" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2. CHECK POSITION SWITCH
Recheck continuity of shift actuator position switch.
Refer to TF-97, "
ACTUATOR AND ACTUATOR POSITION SWITCH" .
Continuity should exist.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace position switch.
3. CHECK INPUT SIGNAL
Do you have CONSULT-II?
Ye s o r N o
Yes >> GO TO 4.
No >> GO TO 5.
4. CHECK INPUT SIGNAL
With CONSULT-II
1. Start engine (idling).
2. Select “SELF-DIAG RESULTS” in Select Diag Mode.
3. Read out self-diagnostic result.
OK or NG
OK >> GO TO 6.
NG >> Check the following.

Continuity between transfer control unit and transfer
control device.

Check ground circuit between transfer control device
and ground.
WDIA0078E
SMT978D

SHIFT ACTUATOR POSITION SWITCH
TF-81
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
5. CHECK INPUT SIGNAL
Without CONSULT-II
1. Start engine (idling).
2. Check voltage transfer control unit harness connector E143 ter-
minal 27 (W/L) [or 44 (LG/B)] and ground while 4WD shift switch
is set from 4H to 4LO (or from 4LO to 4H).
3. Result
OK or NG
OK >> GO TO 6.
NG >> Check the following.

Continuity between transfer control unit and transfer control device.

Check ground circuit between transfer control device and ground.
6. PERFORM SELF-DIAGNOSIS AGAIN
After driving for a while, perform self-diagnosis again.
Refer to TF-27, "
Trouble Diagnosis without CONSULT-II" .
OK or NG
OK >> Inspection End.
NG >> 1. Perform transfer control unit/output signal inspection. Refer to TF-55, "
TRANSFER CONTROL
UNIT INSPECTION TABLE" .
2. If NG, recheck transfer control unit pin terminals for damage or loose connection with harness
connector.
SMT830D
Terminal ConditionVo l ta g e
(Approx.)
274WD shift switch is
set to 4HLess than 1V
4WD shift switch is
set except 4HBattery voltage
444WD shift switch is
set to 4LOLess than 1V
4WD shift switch is
set except 4LOBattery voltage

TF-82
SHIFT ACTUATOR CIRCUIT
Revision: August 20072004 QX56
SHIFT ACTUATOR CIRCUITPFP:00000
Diagnostic ProcedureEDS0018D
1. SHIFT ACTUATOR CIRCUIT
Refer to TF-97, "
TRANSFER SHIFT RELAY (HIGH & LOW)" and TF-97, "ACTUATOR AND ACTUATOR
POSITION SWITCH" .
OK or NG
OK >> GO TO 2.
NG >> Repair or replace transfer shift relay and actuator and actuator position switch.
2. CHECK POWER SOURCE OF TRANSFER SHIFT (HI & LOW) RELAY
1. Disconnect transfer control device harness connector F58.
2. Turn ignition switch to ON (Do not start engine).
3. Check voltage between transfer shift HIGH relay E46 and LOW relay E47 terminal 5 (R) and ground.
OK or NG
OK >> GO TO 3.
NG >> Check the following.

Continuity between ignition switch and transfer shift HIGH & LOW relays

Ignition switch and No. 57 fuse (20A)
WDIA0089E
Voltage : Battery voltage
LDIA0080E

SHIFT ACTUATOR CIRCUIT
TF-83
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
3. CHECK POWER SOURCE OF TRANSFER CONTROL DEVICE
1. Disconnect transfer control device harness connector F58.
2. Turn ignition switch to ON. (Do not start engine)
3. Turn 4WD shift switch from 4H to 4LO (or from 4LO to 4H).
4. Check voltage between transfer control device harness connec-
tor F58 terminal 21 (R/L) [or 24 (P/G)] and ground.
OK or NG
OK >> GO TO 4.
NG >> Check the following.

Harness and connector from transfer shift HIGH and LOW relays to transfer control device har-
ness terminal

Ground circuit between transfer control device and ground.
4. CHECK INPUT SIGNAL
Do you have CONSULT-II?
Ye s o r N o
Yes >> GO TO 5.
No >> GO TO 6.
5. CHECK INPUT SIGNAL
With CONSULT-II
1. Start engine (idling).
2. Select “SELF-DIAG RESULTS” in Select Diag Mode.
3. Read out self-diagnostic result.
OK or NG
OK >> GO TO 8.
NG >> GO TO 7.Voltage : Battery voltage
LDIA0081E
LDIA0082E
SMT978D

TF-84
SHIFT ACTUATOR CIRCUIT
Revision: August 20072004 QX56
6. CHECK INPUT SIGNAL
Without CONSULT-II
1. Start engine (idling).
2. Check voltage between transfer control unit harness connector
E142 terminal 4 (Y/L) [or 13 (G/B)] and ground while 4WD shift
switch is set from 4H to 4LO (or from 4LO to 4H).
3. Result
OK or NG
OK >> GO TO 8.
NG >> GO TO 7.
7. CHECK HARNESS CONTINUITY BETWEEN TRANSFER CONTROL UNIT AND TRANSFER SHIFT
HIGH AND LOW RELAYS
OK or NG
OK >> GO TO 8.
NG >> Repair and replace harness connector between transfer control unit and transfer shift HIGH or
LOW relay.
8. PERFORM SELF-DIAGNOSIS AGAIN
After driving for a while, perform self-diagnosis again.
Refer to TF-27, "
Trouble Diagnosis without CONSULT-II" .
OK or NG
OK >> Inspection End.
NG >> 1. Perform transfer control unit/output signal inspection. Refer to TF-55, "
TRANSFER CONTROL
UNIT INSPECTION TABLE" .
2. If NG, recheck transfer control unit pin terminals for damage or loose connection with harness
connector.
LDIA0083E
Terminal ConditionVo l ta g e
(Approx.)
4While actuator is
operating for 4H to
4LOBattery voltage
Actuator does not
operate0V
13While actuator is
operating for 4LO to
4HBattery voltage
Actuator does not
operate0V

TROUBLE DIAGNOSES FOR SYMPTOMS
TF-85
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
TROUBLE DIAGNOSES FOR SYMPTOMSPFP:00007
Symptom 1. 4WD Shift Indicator Lamp Does Not Turn ON (Although the ignition
switch is turned ON, all the 4WD indicator lamps do not turn ON for 1 second)
EDS0018E
1. CHECK TRANSFER CONTROL UNIT POWER SOURCE
1. Turn ignition switch to OFF position and disconnect transfer control unit harness connector E142.
2. Turn ignition switch to ON position. (Do not start engine.)
3. Check voltage between transfer control unit harness connector
E142 terminals 16 (Y/R), 22 (Y/R) and ground.
OK or NG
OK >> GO TO 2.
NG >> Check the following.

Continuity between ignition switch and transfer control unit

Ignition switch and No. 49 fuse (10A)
WDIA0071E
WDIA0079E
Voltage : Battery voltage
LDIA0086E

TF-86
TROUBLE DIAGNOSES FOR SYMPTOMS
Revision: August 20072004 QX56
2. CHECK TRANSFER CONTROL UNIT GROUND CIRCUIT
1. Turn ignition switch to OFF position.
2. Disconnect transfer control unit harness connectors E142 and
E143.
3. Measure resistance between transfer control unit harness con-
nectors E142 and E143 terminals 3(B), 6(B), 45(B) and ground.
OK or NG
OK >> GO TO 3.
NG >> Check continuity between transfer control unit and
ground.
3. CHECK PROCEDURES FROM THE BEGINNING AGAIN
Check again.
OK or NG
OK >> Inspection End.
NG >> 1. Perform transfer control unit input/output signal inspection. Refer to TF-55, "
TRANSFER CON-
TROL UNIT INSPECTION TABLE" .
2. If NG, recheck transfer control unit pin terminals for damage or loose connection with harness
connector. Resistance : Continuity should exist.
LDIA0087E

TROUBLE DIAGNOSES FOR SYMPTOMS
TF-87
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: August 20072004 QX56
Symptom 2. 4WD Warning Lamp Does Not Turn ON (Although the ignition
switch is turned ON, the 4WD warning lamp does not turn ON)
EDS0018F
1. CHECK TRANSFER CONTROL UNIT POWER SOURCE
1. Turn ignition switch to OFF position and disconnect transfer control unit harness connector E142.
2. Turn ignition switch to ON position (do not start engine).
3. Check voltage between transfer control unit harness connector
E142 terminals 16 (Y/R), 22 (Y/R) and ground.
OK or NG
OK >> GO TO 2.
NG >> Check the following.

Continuity between ignition switch and transfer con-
trol unit

Ignition switch and No. 49 fuse (10A)
2. CHECK TRANSFER CONTROL UNIT GROUND CIRCUIT
1. Turn ignition switch to OFF position.
2. Disconnect transfer control unit harness connectors E142 and
E143.
3. Measure resistance between transfer control unit harness con-
nectors E142 and E143 terminals 3 (B), 6 (B), 45 (B) and
ground.
OK or NG
OK >> GO TO 3.
NG >> Check continuity between transfer control unit and
ground.
3. CHECK 4WD WARNING LAMP CIRCUIT AND COMBINATION METER
Check the following.

Combination meter. Refer to DI-17, "How to Proceed With Trouble Diagnosis" .

Continuity between ignition switch and combination meter

Continuity between combination meter and transfer control unit
OK or NG
OK >> Replace transfer control unit. Refer to TF-98, "Removal and Installation" .
NG >>

Repair or replace harness or connector.

Replace combination meter. Refer to DI-25, "Removal and Installation of Combination Meter" .
WDIA0080E
Voltage : Battery voltage
LDIA0089E
Resistance : Continuity should exist.
LDIA0087E