climate control INFINITI QX56 2004 Factory Service Manual

ATC-54
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
Using Confirmation/Adjustment Mode (NAVI)
NOTE:
Ambient temperature must be at least 10° C (50° F) to run self-diagnosis.
1. Start engine.
2. Turn the audio system off.
3. While pressing the "PAUSE/MUTE" button, turn the volume con-
trol dial clockwise or counterclockwise for 30 clicks or more.
(When the self diagnosis mode is started, a short beep will be
heard.)

Shifting from current screen to previous screen is performed
by pressing "PREV" button.
4. The initial self-diagnosis screen will be shown, and items "Self-
Diagnosis (DCU)", "Self-Diagnosis (NAVI)", "Confirmation/
Adjustment" and "CAN DIAG SUPPORT MONITOR" will
become selective.
5. When "Confirmation/Adjustment" is selected on the initial self-
diagnosis screen, the operation will enter CONFIRMATION/
ADJUSTMENT mode. In this mode, check and adjustment of
each item will become possible.
6. The initial trouble diagnosis screen will be shown, and items
"display Diagnosis", "Vehicle Signals", "Auto Climate Control"
and "Navigation" will become selective.
7. Select the "Auto Climate Control" switch on "CONFIRMATION/
ADJUSTMENT" screen to display the "Auto Climate Control"
diagnosis screen to begin diagnosis The front blower speed indi-
cation bars will flash and the ambient temperature display will
indicate 0° during the self-diagnosis. Fault codes (if any are
present) will be displayed in the ambient temperature display area. Refer to ATC-55, "
SELF-DIAGNOSIS
CODE CHART" .
WKIA1504E
SKIA4207E
SKIA4220E

ATC-182
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: August 20072004 QX56
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Service Data and Specifications (SDS)EJS002DZ
COMPRESSOR
LUBRICANT
REFRIGERANT
ENGINE IDLING SPEED
Refer to EC-32, "Idle Speed and Ignition Timing Check" .
BELT TENSION
Refer to MA-12, "DRIVE BELT TENSION" .
MakeZEXEL VALEO CLIMATE CONTROL
ModelDKS-17D
Ty p eSwash plate
Displacement
cm
3 (cu in) / revolution175.5 (10.7) / revolution
Cylinder bore × stroke
mm (in)30.5 (1.20) x 24.0 (0.94)
Direction of rotation Clockwise (viewed from drive end)
Drive beltPoly V
NameNISSAN A/C System Lubricant Type S (DH-PS)
Part number KLH00-PAGS0
Capacity
m (US fl oz, lmp fl oz)Total in system 290 (9.8, 10.2)
Compressor (service part) charging amountRefer to AT C - 2 2 , "
Lubricant Adjustment Procedure
for Compressor Replacement" .
Ty p eHFC-134a (R-134a)
Capacity
kg (lb)1.08 ± 0.05 (2.38 ± 0.11)

NAVIGATION SYSTEM
AV-101
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
On Board Self-Diagnosis FunctionEKS007LT
DESCRIPTION

Diagnosis function consists of the self-diagnosis mode performed automatically and the CONFIRMATION/
ADJUSTMENT mode operated manually.

Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.

CONFIRMATION/ADJUSTMENT mode is used to perform trouble diagnosis that require operation and
judgment by an operator (trouble that cannot be automatically judged by the system), to check/change the
set value, and to display the History of Errors of the navigation system.
DIAGNOSIS ITEM
NOTE:
Make the status that is set by D/N function be shown.
Self-Diagnosis Mode (DCU)EKS007LU
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
Mode Description
Self-diagnosis (DCU) Display control unit diagnosis.
Self-diagnosis (NAVI)

NAVI Control unit diagnosis (DVD-ROM drive) will not be diagnosed
when no map DVD-ROM is in it.

Analyzes connection between the NAVI control unit and the GPS
antenna and operation of each unit.
CONFIRMATION/
ADJUSTMENTDisplay diagnosisIn display control unit mode, color tone and shading of the screen can be
checked by the display of a color bar and a gray scale.
Vehicle signalsIn display control unit mode, analyzes the following vehicle signals: Vehi-
cle speed signal, light signal
NOTE , ignition switch signal, and reverse sig-
nal.
Auto Climate Control A/C self-diagnosis of A/C system.
NavigationDisplay diagnosisIn NAVI C/U mode, color tone and shading of the screen can be checked
by the display of a color bar and a gray scale.
Vehicle signalsIn NAVI C/U mode, analyzes the following vehicle signals: Vehicle speed
signal, light signal, ignition switch signal, and reverse signal.
History of ErrorsDiagnosis results previously stored in the memory (before turning ignition
switch ON) are displayed in this mode. Time and location when/where the
errors occurred are also displayed.
Naviga-
tionDisplay Lon-
gitude & Lat-
itudeDisplay the map. Use the joystick to adjust position. Longitude and latitude
will be displayed.
Speed Cali-
brationUnder ordinary conditions, the navigation system distance measuring
function will automatically compensate for minute decreases in wheel and
tire diameter caused by tire wear or low-pressure. Speed calibration imme-
diately restores system accuracy in cases such as when distance calibra-
tion is needed because of the use of tire chains in inclement weather.
Angle
adjustmentCorrects difference between actual turning angle of a vehicle and turning
angle of the car mark on the display.
Initialize
LocationThis mode is for initializing the current location. Use when the vehicle is
transported a long distance on a trailer, etc.
CAN DIAG SUPPORT MONITOR Display status of CAN communication.

NAVIGATION SYSTEM
AV-107
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
Confirmation/Adjustment ModeEKS007LW
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “PAUSE/MUTE” button, turn the volume con-
trol dial clockwise or counterclockwise for 30 clicks or more.
(When the self-diagnosis mode is started, a short beep will be
heard.)

Shifting from current screen to previous screen is performed
by pressing “PREV” button.
4. The initial self-diagnosis screen will be shown, and items “Self-
Diagnosis (DCU)”, “Self-Diagnosis (NAVI)”, “Confirmation/
Adjustment” and “CAN DIAG SUPPORT MONITOR” will
become selective.
5. When “Confirmation/Adjustment” is selected on the initial self-
diagnosis screen, the operation will enter the CONFIRMATION/
ADJUSTMENT mode. In this mode, check and adjustment of
each item will become possible.
6. The initial trouble diagnosis screen will be shown, and items
“Display Diagnosis”, “Vehicle Signals”, “Auto Climate Control”
and “Navigation” will become selective.
7. Select each switch on “CONFIRMATION/ADJUSTMENT”
screen to display the relevant diagnosis screen.
WKIA1504E
SKIA4207E
SKIA4220E