trailer INFINITI QX56 2006 Factory Service Manual

NAVIGATION SYSTEMAV-111
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
On Board Self-Diagnosis FunctionEKS00BJP
DESCRIPTION

Diagnosis function consists of the self-diagnosis mode performed automatically and the CONFIRMATION/
ADJUSTMENT mode operated manually.

Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.

CONFIRMATION/ADJUSTMENT mode is used to perform trouble diagnosis that require operation and
judgment by an operator (trouble that cannot be automatically judged by the system), to check/change the
set value, and to display the History of Errors of the navigation system.
DIAGNOSIS ITEM
NOTE:
Make the status that is set by D/N function be shown.
ModeDescription
Self-diagnosis (DCU) Display control unit diagnosis.
Self-diagnosis (NAVI)

NAVI Control unit diagnosis (DVD-ROM drive) will not be diagnosed
when no map DVD-ROM is in it.

Analyzes connection between the NAVI control unit and the GPS
antenna and operation of each unit.
CONFIRMATION/
ADJUSTMENT Display diagnosis
In display control unit mode, color tone and shading of the screen can be
checked by the display of a color bar and a gray scale.
Vehicle signals In display control unit mode, analyzes the following vehicle signals: Vehi-
cle speed signal, light signal
NOTE , ignition switch signal, and reverse sig-
nal.
Auto Climate Control A/C self-diagnosis of A/C system.
Navigation Display diagnosis
In NAVI C/U mode, color tone and shading of the screen can be checked
by the display of a color bar and a gray scale.
Vehicle signals In NAVI C/U mode, analyzes the following vehicle signals: Vehicle speed
signal, light signal, ignition switch signal, and reverse signal.
History of Errors Diagnosis results previously stored in the memory (before turning ignition
switch ON) are displayed in this mode. Time and location when/where the
errors occurred are also displayed.
Naviga-
tion Display Lon-
gitude & Lat-
itude
Display the map. Use the joystick to adjust position. Longitude and latitude
will be displayed.
Speed Cali-
bration Under ordinary conditions, the navigation system distance measuring
function will automatically compensate for minute decreases in wheel and
tire diameter caused by tire wear or low-pressure. Speed calibration imme-
diately restores system accuracy in cases such as when distance calibra-
tion is needed because of the use of tire chains in inclement weather.
Angle
adjustment Corrects difference between actual turning angle of a vehicle and turning
angle of the car mark on the display.
Initialize
Location This mode is for initializing the current location. Use when the vehicle is
transported a long distance on a trailer, etc.
CAN DIAG SUPPORT MONITOR Display status of CAN communication.

BCM (BODY CONTROL MODULE)BCS-7
C
DE
F
G H
I
J
L
M A
B
BCS
Revision: November 2009 2006 QX56

BCM is activated with low current consumption mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state:
–Ignition switch
–Key switch (insert)
–Hazard switch
–Main door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back latch (door ajar switch)
–Glass hatch ajar switch
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Front door lock assembly LH (key cylinder switch)

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY

Power door lock system. Refer to BL-16, "POWER DOOR LOCK SYSTEM" .

Remote keyless entry system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .

Power window system. Refer to GW-15, "POWER WINDOW SYSTEM" . NOTE

Sunroof system. Refer to RF-10, "SUNROOF" . NOTE

Room lamp timer. Refer to LT- 1 3 4 , "INTERIOR ROOM LAMP" .

Warning chime system. Refer to DI-43, "WARNING CHIME" .

Turn signal and hazard warning lamps system. Refer to LT- 8 0 , "TURN SIGNAL AND HAZARD WARNING
LAMPS" .

Trailer turn signal and hazard warning lamps system (if equipped). Refer to LT- 1 2 6 , "TRAILER TOW" .

Rear wiper and washer system. Refer to WW-32, "REAR WIPER AND WASHER SYSTEM" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R

Panic system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .

Vehicle security system. Refer to BL-75, "VEHICLE SECURITY (THEFT WARNING) SYSTEM" .

IVIS (NATS) system. Refer to BL-137, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .

Headlamp, tail lamp, front fog lamp, auto light and battery saver control systems. Refer to LT- 5 , "HEAD-
LAMP (FOR USA)" , LT- 3 3 , "HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -" , LT- 111 ,
"PARKING, LICENSE PLATE AND TAIL LAMPS" , LT- 6 9 , "FRONT FOG LAMP" or LT- 4 7 , "AUTO LIGHT
SYSTEM" .

Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .

Rear window defogger system. Refer to GW-74, "REAR WINDOW DEFOGGER" .
MAJOR COMPONENTS AND CONTROL SYSTEM
System InputOutput
Remote keyless entry system Remote keyless entry receiver (keyfob)

All door locking actuators

Back door opener actuator

Turn signal lamps
Power door lock system

Front power door lock/unlock switch (LH, RH)

All door switches

Key switch All door locking actuators

BCS-8
BCM (BODY CONTROL MODULE)
Revision: November 20092006 QX56
CAN Communication System DescriptionEKS00D7X
Refer to LAN-26, "CAN COMMUNICATION" .
Power supply [ignition (IGN)/retained
accessory power (RAP)] to power win-
dow and sunroof IGN/RAP supply
Power supply to power window and
sunroof system
Power supply (BAT) to power window
and sunroof Battery power supply Power supply to power window and
sunroof system
Panic alarm

Key switch

Remote keyless entry receiver (keyfob) IPDM E/R
Auto light system

Optical sensor

Combination switch IPDM E/R
Battery saver control

Ignition switch

Combination switch

Front door switch LH and RH IPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Room lamp timer

Key switch

Remote keyless entry receiver (keyfob)

Main power window and door lock/unlock switch

Front door lock assembly LH (key cylinder switch)

All door switches Interior room lamp
Key warning chime

Key switch

Front door switch LH Combination meter (warning
buzzer)
Light warning chime

Combination switch

Key switch

Front door switch LH Combination meter (warning
buzzer)
Vehicle-speed-sensing intermittent
wiper

Combination switch

Combination meter IPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Air conditioner switch signal Front air control ECM
Blower fan switch signal Front air control ECM
Low tire pressure warning system Remote keyless entry receiver

Combination meter

Display control unit
Trailer tow (if equipped) Combination switch Trailer turn signal relays
Vehicle security system

Remote keyless entry receiver (keyfob)

Main power window and door lock/unlock switch

Power window and door lock/unlock switch RH

Front door lock assembly LH (key cylinder switch)

All door switches

Back door latch (door ajar switch)

IPDM E/R

Security indicator lamp
System
InputOutput

LT-3
C
DE
F
G H
I
J
L
M A
B
LT
Revision: November 2009 2006 QX56
STOP LAMP .....................................................
. 108
Removal and Installation ..................................... . 108
HIGH_MOUNTED STOP LAMP ...................... . 108
STOP LAMP ..................................................... . 108
BACK-UP LAMP ................................................... . 109
Wiring Diagram — BACK/L — ............................ . 109
Bulb Replacement ............................................... .. 110
BACK-UP LAMP .............................................. .. 110
INSTALLATION ................................................ .. 110
Removal and Installation ..................................... .. 110
BACK-UP LAMP .............................................. .. 110
PARKING, LICENSE PLATE AND TAIL LAMPS .. .. 111
Component Parts and Harness Connector Location . . 111
System Description ............................................. . . 111
OPERATION BY LIGHTING SWITCH ............. .. 112
COMBINATION SWITCH READING FUNCTION .. 112
EXTERIOR LAMP BATTERY SAVER CONTROL .. 112
CAN Communication System Description ........... .. 112
Schematic ........................................................... .. 113
Wiring Diagram — TAIL/L — ................................. 114
Terminals and Reference Values for BCM .......... .. 117
Terminals and Reference Values for IPDM E/R .. .. 118
How to Proceed With Trouble Diagnosis ............. .. 118
Preliminary Check ............................................... .. 118
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. .. 118
CONSULT-II Functions ........................................ .. 119
Parking, License Plate and/or Tail Lamps Do Not
Illuminate ............................................................. . 120
Parking, License Plate and Tail Lamps Do Not Turn
OFF (After Approx. 10 Minutes) .......................... . 123
Bulb Replacement ............................................... . 124
FRONT PARKING LAMP ................................. . 124
LICENSE PLATE LAMP ................................... . 124
SIDE MARKER LAMP (FRONT) ...................... . 124
TAIL LAMP ....................................................... . 124
Removal and Installation ..................................... . 124
FRONT PARKING LAMP ................................. . 124
LICENSE PLATE LAMP ................................... . 124
INSTALLATION ................................................ . 124
SIDE MARKER LAMP (REAR) ........................ . 124
TAIL LAMP ....................................................... . 124
REAR COMBINATION LAMP ............................... . 125
Bulb Replacement ............................................... . 125
SIDE MARKER LAMP (REAR) ........................ . 125
TAIL LAMP ....................................................... . 125
TURN SIGNAL ................................................. . 125
STOP LAMP ..................................................... . 125
INSTALLATION ................................................ . 125
Removal and Installation ..................................... . 125
REAR COMBINATION LAMP .......................... . 125
TRAILER TOW ...................................................... . 126Component Parts and Harness Connector Location
.126
System Description .............................................. .126
TRAILER TAIL LAMP OPERATION ................. .127
TRAILER BRAKE, TURN SIGNAL AND HAZARD
LAMP OPERATION .......................................... .127
TRAILER BRAKE OPERATION ....................... .128
TRAILER POWER SUPPLY OPERATION ....... .128
Schematic ............................................................ .129
Wiring Diagram — T/TOW — .............................. .130
INTERIOR ROOM LAMP ....................................... .134
Component Parts and Harness Connector Location .134
System Description .............................................. .135
POWER SUPPLY AND GROUND ................... .135
SWITCH OPERATION ..................................... .136
ROOM LAMP TIMER OPERATION ................. .136
INTERIOR LAMP BATTERY SAVER CONTROL .137
Schematic ............................................................ .138
Wiring Diagram — INT/L — ................................. .140
Terminals and Reference Values for BCM ........... .147
How to Proceed With Trouble Diagnosis ............. .148
Preliminary Check ............................................... .148
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT .......................................... .148
CONSULT-II Function (BCM) .............................. .149
CONSULT-II OPERATION ................................ .149
WORK SUPPORT ............................................ .150
DATA MONITOR .............................................. .150
ACTIVE TEST .................................................. .151
Room/Map Lamp Control Does Not Operate ...... .151
Personal Lamp Control Does Not Operate (Room/
Map Lamps Operate) ........................................... .153
All Step/Foot/Puddle Lamps Do Not Operate ...... .154
All Interior Room Lamps Do Not Operate ............ .155
Ignition Keyhole Illumination Control Does Not
Operate ................................................................ .155
ILLUMINATION ...................................................... .157
Component Parts and Harness Connector Location .157
System Description .............................................. .157
ILLUMINATION OPERATION BY LIGHTING
SWITCH ........................................................... .158
EXTERIOR LAMP BATTERY SAVER CONTROL .159
CAN Communication System Description ........... .159
Schematic ............................................................ .160
Wiring Diagram — ILL — ..................................... .163
Removal and Installation of Illumination Control
Switch .................................................................. .174
REMOVAL ........................................................ .174
INSTALLATION ................................................ .174
BULB SPECIFICATIONS ....................................... .175
Headlamp ............................................................ .175
Exterior Lamp ...................................................... .175
Interior Lamp/Illumination .................................... .175

LT-126
TRAILER TOW
Revision: November 20092006 QX56
TRAILER TOWPFP:93020
Component Parts and Harness Connector LocationEKS00BB1
System DescriptionEKS00BB2
Power is supplied at all times

to ignition relay, located in the IPDM E/R (intelligent power distribution module engine room), and

through 50A fusible link (letter f , located in the fuse and fusible link box)

to BCM (body control module) terminal 70, and

through 10A fuse (No. 32, located in the IPDM E/R)
1. Fuse and fusible link box2. IPDM E/R fuse layout 3. Fuse and relay box
4. IPDM E/R E118, E119, E120, E121, E122, E123, E124 5. A. Steering column
B. Data link connector M22
C. BCM M18, M19, M20
(View with instrument lower panel
LH removed) 6. A. Trailer turn relay LH E156
B. Battery
C. Trailer tow relay 2 E140
D. Trailer turn relay RH E157
7. A. Trailer tow relay 1 M51 B. Electric brake (pre-wiring) M76
(View with instrument lower panel
LH removed) 8. Trailer connector C2
9. Combination switch (lighting switch)
M28
WKIA4616E

TRAILER TOWLT-127
C
DE
F
G H
I
J
L
M A
B
LT
Revision: November 2009 2006 QX56

through IPDM E/R terminal 61

to trailer tow relay 1 terminal 3, and

through 20A fuse (No. 53, located in the IPDM E/R)

to CPU (central processing unit) of the IPDM E/R, and

through 30A fusible link (letter j , located in the fuse and fusible link box)

to trailer tow relay 2 terminals 3 and 6, and

through 40A fusible link (letter k , located in the fuse and fusible link box)

to electric brake (pre-wiring) terminal 5.
With the ignition switch in the ON or START position, power is supplied

to ignition relay, located in the IPDM E/R, and

through 10A fuse (No. 59, located in the fuse and relay box)

to BCM terminal 38, and

through 10A fuse (No. 51, located in the IPDM E/R)

to trailer tow relay 2 terminal 1.
Ground is supplied

to BCM terminal 67

to electric brake (pre-wiring) terminal 1, and

through grounds M57, M61 and M79, and

to IPDM E/R terminals 38 and 59

to trailer tow relay 1 terminal 2

to trailer tow relay 2 terminal 2, and

to trailer connector terminal 2

to trailer turn relay LH and RH terminal 2

through grounds E9, E15 and E24.
TRAILER TAIL LAMP OPERATION
The trailer tail lamps are controlled by the trailer tow relay 1.
With the lighting switch in the parking and tail lamp ON (1ST) position, AUTO position (and the auto light sys-
tem is activated) or headlamp ON (2ND) position, power is supplied

through the tail lamp relay, located in the IPDM E/R

through 10A fuse (No. 36, located in the IPDM E/R)

through IPDM E/R terminal 49

to trailer tow relay 1 terminal 1.
When energized, trailer tow relay 1 supplies tail lamp power to trailer connector terminal 6.
TRAILER BRAKE, TURN SIGNAL AND HAZARD LAMP OPERATION
The trailer brake, turn signal and hazard lamps are controlled by the BCM through trailer turn relays (LH and
RH). When the brake pedal is depressed, the BCM receives stop lamp switch signal through CAN communi-
cation. If the brake pedal is depressed or either turn signal or the hazard lamps are turned on, the BCM sup-
plies voltage to the trailer turn relays (LH and RH) to make them cycle on and off.
Trailer turn relay LH output is supplied

through BCM terminal 52

to trailer turn relay LH terminal 1.
Trailer turn relay RH output is supplied

through BCM terminal 51

to trailer turn relay RH terminal 1.
Left trailer brake, turn signal and hazard lamp output is supplied

through trailer turn relay LH terminal 3

to trailer connector terminal 1.
Right trailer brake, turn signal and hazard lamp output is supplied

through trailer turn relay RH terminal 3

LT-128
TRAILER TOW
Revision: November 20092006 QX56

to trailer connector terminal 4.
TRAILER BRAKE OPERATION
The trailer brake is controlled by the electric brake. The electric brake receives stop lamp switch signal at elec-
tric brake (pre-wiring) terminal 2 when the brake pedal is depressed.
When the brake pedal is depressed, power is supplied by the electric brake

through electric brake (pre-wiring) terminal 3

to trailer connector terminal 3.
TRAILER POWER SUPPLY OPERATION
The trailer power supply is controlled by the trailer tow relay 2.
When the ignition switch is in the ON or START position, power is supplied

through 10A fuse (No. 51, located in the IPDM E/R)

through IPDM E/R terminal 16

to trailer tow relay 2 terminal 1.
When energized, the trailer tow relay 2 supplies power

through trailer tow relay 2 terminals 5 and 7

to trailer connector terminal 5.

TRAILER TOWLT-129
C
DE
F
G H
I
J
L
M A
B
LT
Revision: November 2009 2006 QX56
SchematicEKS00BB3
WKWA3664E

LT-130
TRAILER TOW
Revision: November 20092006 QX56
Wiring Diagram — T/TOW —EKS00BB4
WKWA3665E

TRAILER TOWLT-131
C
DE
F
G H
I
J
L
M A
B
LT
Revision: November 2009 2006 QX56
WKWA3666E