steering INFINITI QX56 2006 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2006, Model line: QX56, Model: INFINITI QX56 2006Pages: 3383, PDF Size: 51.76 MB
Page 2765 of 3383
RAX-4
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
Revision: November 20092006 QX56
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting ChartEDS001XM
Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: ApplicableReference page
—
RAX-8—
RAX-5—
RFD-7, "
NVH Troubleshooting Chart
"
FAX-4, "
NVH Troubleshooting Chart
" (FAX), FSU-4, "
NVH Troubleshooting Chart
" (FSU)
RSU-5, "
NVH Troubleshooting Chart
"
WT-4, "
NVH Troubleshooting Chart
"
WT-4, "
NVH Troubleshooting Chart
"
PR-3, "
NVH Troubleshooting Chart
"
BR-5, "
NVH Troubleshooting Chart
"
PS-5, "
NVH Troubleshooting Chart
"
Possible cause and SUSPECTED PARTS
Excessive joint angle
Joint sliding resistance
Imbalance
Improper installation, looseness
Parts interference
DIFFERENTIAL
FRONT AXLE AND FRONT SUSPENSION
REAR SUSPENSION
TIRES
ROAD WHEEL
PROPELLER SHAFT
BRAKES
STEERING
Symptom Noise
×× ×× ×× ×××××
Shake × × ×× × ×××××
Vibration ×× ×× × × × ×
Shimmy ×× ×××××
Shudder × × ×× ××
Poor quality ride or handling ×× ×× ×× ×
Page 2812 of 3383
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTINGRFD-7
CE F
G H
I
J
K L
M A
B
RFD
Revision: November 2009 2006 QX56
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting ChartEDS0044N
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
RFD-23RFD-17RFD-17RFD-18RFD-18RFD-8
PR-3, "
NVH Troubleshooting Chart
"
RAX-4, "
NVH Troubleshooting Chart
"
RSU-5, "
NVH Troubleshooting Chart
"
WT-4, "
NVH Troubleshooting Chart
"
WT-4, "
NVH Troubleshooting Chart
"
FAX-4, "
NVH Troubleshooting Chart
"
BR-5, "
NVH Troubleshooting Chart
"
PS-5, "
NVH Troubleshooting Chart
"
Possible cause and SUSPECTED PARTS
Gear tooth rough
Gear contact improper
Tooth surfaces worn
Backlash incorrect
Companion flange excessive runout
Gear oil improper
PROPELLER SHAFT
REAR AXLE
REAR SUSPENSION
TIRES
ROAD WHEEL
DRIVE SHAFT
BRAKES
STEERING
Symptom FINAL DRIVE Noise ××××××××××××××
Page 2844 of 3383
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTINGRSU-5
C
DF
G H
I
J
K L
M A
B
RSU
Revision: November 2009 2006 QX56
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting ChartEES001H1
Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: ApplicableReference page
RSU-26RSU-35
—
—
—
RSU-26
RSU-28RSU-42
PR-3, "
NVH Troubleshooting Chart
"
RFD-7, "
NVH Troubleshooting Chart
"
FAX-4, "
NVH Troubleshooting Chart
"
FSU-4, "
NVH Troubleshooting Chart
"
WT-4, "
NVH Troubleshooting Chart
"
WT-4, "
NVH Troubleshooting Chart
"
RAX-4, "
NVH Troubleshooting Chart
"
PS-5, "
NVH Troubleshooting Chart
"
BR-5, "
NVH Troubleshooting Chart
"
Possible cause and SUSPECTED PARTS
Improper installation, looseness
Shock absorber deformation, damage or deflection
Bushing or mounting deterioration
Parts interference
Spring fatigue
Suspension looseness
Incorrect wheel alignment
Stabilizer bar fatigue
PROPELLER SHAFT
DIFFERENTIAL
FRONT AXLE
FRONT SUSPENSION
TIRES
ROAD WHEEL
DRIVE SHAFT
BRAKES
STEERING
Symptom Noise
×××××× ××× ××××××
Shake ×××× × × × ××××××
Vibration ××××× × × ×× × ×
Shimmy ×××× × × ××× ××
Shudder ××× × ××× ××
Poor quality ride or handling ××××× ×× × ×××
Page 2867 of 3383
RSU-28
REAR SUSPENSION ASSEMBLY
Revision: November 20092006 QX56
Wheel Alignment InspectionEES001HH
Rear Wheel Alignment Adjusting Bolts
PRELIMINARY INSPECTION
WARNING:
Always adjust the alignment with the vehicle on a flat surface. Use CONSULT-II “EXHAUST SOLE-
NOID” active test to release the air pressure from the rear load leveling air suspension system.
NOTE:
If alignment is out of specification, inspect and replace any damaged or worn rear suspension parts before
making any adjustments.
1. Check and adjust the wheel alignment with the vehicle under unladen conditions. “Unladen conditions”
means that the fuel, coolant, and lubricant are full; and that the spare tire, jack, hand tools and mats are in
their designated positions.
2. Check the tires for incorrect air pressure and excessive wear.
3. Check the wheels for runout and damage. Refer to WT-5, "
Inspection" .
4. Check the wheel bearing axial end play.
5. Check the shock absorbers. Refer to RSU-27, "
SHOCK ABSORBER INSPECTION" .
6. Check each mounting point of the suspension components for any excessive looseness or damage.
7. Check each link, arm, and the rear suspension member for any damage.
8. Check the vehicle height. Refer to RSU-49, "
Wheelarch Height (Unladen*1 )" .
If vehicle height is not within ± 10 mm (0.39 in) of the specification, perform the control unit initialization
procedure. Refer to RSU-47, "
Initialization Procedure" .
GENERAL INFORMATION AND RECOMMENDATIONS
1. A Four-Wheel Thrust Alignment should be performed.
This type of alignment is recommended for any NISSAN vehicle.
The four-wheel “thrust” process helps ensure that the vehicle is properly aligned and the steering wheel
is centered.
The alignment machine itself should be capable of accepting any NISSAN vehicle.
The alignment machine should be checked to ensure that it is level.
2. Make sure the alignment machine is properly calibrated.
Your alignment machine should be regularly calibrated in order to give correct information.
WEIA0102E
1. Rear lower link adjusting bolt, LH 2. Front lower link adjusting bolt, LH 3. Front lower link adjusting bolt, RH
4. Rear lower link adjusting bolt, RH
Axial end play : 0 mm (0 in)
Page 2932 of 3383
SE-1
SEAT
I BODY
CONTENTS
C
DE
F
G H
J
K L
M
SECTION
A
B
SE
Revision: November 2009 2006 QX56
PRECAUTIONS .....................................................
..... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 3
Precautions for Work ........................................... ..... 3
PREPARATION ...................................................... ..... 4
Special Service Tool ............................................ ..... 4
Commercial Service Tool .................................... ..... 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5 CUSTOMER INTERVIEW ................................ ..... 5
DUPLICATE THE NOISE AND TEST DRIVE .. ..... 6
CHECK RELATED SERVICE BULLETINS ...... ..... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ................................................. ..... 6
REPAIR THE CAUSE ...................................... ..... 6
CONFIRM THE REPAIR .................................. ..... 7
Generic Squeak and Rattle Troubleshooting ...... ..... 7
INSTRUMENT PANEL ..................................... ..... 7
CENTER CONSOLE ........................................ ..... 7
DOORS ............................................................ ..... 7
TRUNK ............................................................. ..... 8
SUNROOF/HEADLINING ................................ ..... 8
OVERHEAD CONSOLE (FRONT AND REAR) ..... 8
SEATS .............................................................. ..... 8
UNDERHOOD .................................................. ..... 8
Diagnostic Worksheet ......................................... ..... 9
AUTOMATIC DRIVE POSITIONER ....................... ....11
Component Parts And Harness Connector Location .... 11
System Description ............................................. ... 12
FAIL-SAFE MODE ........................................... ... 12
CANCEL OF FAIL-SAFE MODE ...................... ... 13
CAN Communication System Description ........... ... 13
Schematic ........................................................... ... 14
Wiring Diagram — AUT/DP — ............................ ... 16
Terminals and Reference Values for BCM .......... ... 26
Terminals and Reference Values for Driver Seat
Control Unit ......................................................... ... 26
Terminals and Reference Values for Automatic Drive Positioner Control Unit ...............................
... 28
Work Flow ............................................................... 30
Preliminary Check ............................................... ... 31
SETTING CHANGE FUNCTION ...................... ... 31
POWER SUPPLY AND GROUND CIRCUIT
INSPECTION ................................................... ... 31
CONSULT-II Function (AUTO DRIVE POS.) ....... ... 34
CONSULT-II INSPECTION PROCEDURE ....... ... 34
SELF-DIAGNOSIS RESULTS .......................... ... 36
DATA MONITOR .............................................. ... 37
ACTIVE TEST ..................................................... 38
CAN Communication Inspection Using CONSULT-
II (Self-Diagnosis) ................................................ ... 38
Symptom Chart ....................................................... 38
Sliding Motor Circuit Inspection ........................... ... 40
Reclining Motor LH Circuit Inspection ................. ... 41
Lifting Motor (Front) Circuit Inspection ................ ... 42
Lifting Motor (Rear) Circuit Inspection ................. ... 44
Pedal Adjusting Motor Circuit Inspection ............. ... 45
Mirror Motor LH Circuit Check ................................ 46
Mirror Motor RH Circuit Check ............................ ... 48
Steering Wheel Tilt Circuit Inspection .................. ... 49
Sliding Sensor Circuit Inspection ......................... ... 51
Reclining Sensor Circuit Inspection ..................... ... 52
Lifting Sensor (Front) Circuit Inspection .............. ... 53
Lifting Sensor (Rear) Circuit Inspection ............... ... 54
Pedal Adjusting Sensor Circuit Inspection ........... ... 55
Mirror Sensor LH Circuit Check ........................... ... 56
Mirror Sensor RH Circuit Check ............................. 57
Steering Wheel Tilt Sensor Circuit Inspection ..... ... 59
Sliding Switch Circuit Inspection .......................... ... 61
Reclining Switch Inspection ................................. ... 62
Lifting Switch (Front) Circuit Inspection ............... ... 64
Lifting Switch (Rear) Circuit Inspection ................ ... 65
Power Seat Switch Ground Inspection ................ ... 66
Pedal Adjusting Switch Circuit Inspection ........... ... 67
Door Mirror Remote Control Switch (Changeover
Switch) Circuit Check ............................................. 69
Door Mirror Remote Control Switch (Mirror Switch)
Circuit Check ....................................................... ... 70
Page 2933 of 3383
SE-2Revision: November 20092006 QX56
Door Mirror Remote Control Switch Ground Circuit
Inspection ............................................................
... 72
Seat Memory Switch Circuit Inspection ............... ... 72
Seat Memory Indicator Lamp Circuit Inspection .. ... 74
Door Mirror Sensor Power Supply and Ground Cir-
cuit inspection ...................................................... ... 75
A/T Device (Park Position Switch) Circuit Inspection ... 76
Steering Wheel Tilt Switch Circuit Inspection ...... ... 77
Front Door Switch LH Circuit Inspection .............. ... 79
UART Communication Line Circuit Inspection ..... ... 80
Removal and Installation ..................................... ... 82
POWER SEAT ........................................................ ... 83
Wiring Diagram — SEAT — for Passenger Seat . ... 83
HEATED SEAT ....................................................... ... 84
Description ........................................................... ... 84
Schematic ............................................................ ... 85
Wiring Diagram — HSEAT — .............................. ... 86
FRONT SEAT ......................................................... ... 91
Removal and Installation ..................................... ... 91
REMOVAL ........................................................ ... 94INSTALLATION .................................................
... 94
Disassembly and Assembly ................................. ... 94
SEATBACK TRIM AND PAD ............................ ... 94
REMOVAL OF SEATBACK ASSEMBLY .......... ... 96
INSTALLATION OF SEATBACK ASSEMBLY .. ... 96
SEAT CUSHION TRIM AND PAD (DRIVER) OR
SEAT CUSHION ASSEMBLY (PASSENGER) .. ... 96
SECOND SEAT ...................................................... ... 98
Removal and Installation ...................................... ... 98
SECOND ROW OUTBOARD ........................... ... 98
SECOND ROW CENTER ................................. ... 98
Disassembly and Assembly ................................. ... 99
THIRD SEAT ........................................................... .105
LH Side Seat ........................................................ .105
REMOVAL ......................................................... .105
INSTALLATION ................................................. .105
DISASSEMBLY AND ASSEMBLY .................... .106
RH Side Seat ....................................................... .107
REMOVAL ......................................................... .107
INSTALLATION ................................................. .108
DISASSEMBLY AND ASSEMBLY .................... .109
Page 2942 of 3383
AUTOMATIC DRIVE POSITIONERSE-11
C
DE
F
G H
J
K L
M A
B
SE
Revision: November 2009 2006 QX56
AUTOMATIC DRIVE POSITIONERPFP:28491
Component Parts And Harness Connector LocationEIS0058U
1. Fuse block (J/B)2. Fuse and relay box3. Fuse and fusible link box
4. A. Automatic drive positioner control unit M33, M34
B. Pedal adjusting motor E109,
E110 5. A. Steering column
B. Key switch and key lock solenoid
M27
C. BCM M18, M19, M20 (View with
instrument panel removed) 6. A. Door mirror remote control switch
D10
B. Seat memory switch D5
LIIA2361E
Page 2943 of 3383
SE-12
AUTOMATIC DRIVE POSITIONER
Revision: November 20092006 QX56
System DescriptionEIS004XE
Refer to Owner's Manual for Automatic Drive Positioner system operating instructions.
The settings (ON/OFF) of the automatic sliding seat (Entry/Exiting operation) at entry/exit can be changed
as desired, using the display unit in the center of the instrument panel. The set content is transmitted by
CAN communication, from display control unit to driver seat control unit.
Using CONSULT-ll, the seat slide amount at entry/exit setting can be changed.
NOTE:
Disconnecting the battery erases the stored memory.
After connecting the battery, insert the key into the ignition cylinder and turn the front door switch LH ON (open) →OFF (close) →ON
(open), the Entry/Exiting function becomes possible.
After Exiting operation is carried out, return operation can be operated.
NOTE:
During automatic operation, if the ignition switch is turned ON →START, the automatic operation is suspended. When the ignition switch
returns to ON, it resumes.
FAIL-SAFE MODE
When any manual and automatic operations are not performed, if any motor operations of seats or pedals are
detected for T2 or more, status is judged “Output error ”.
7. Pedal adjusting switch M96 8. A. Door mirrror LH D4, RH D107
B. Front door switch LH B8
C. Front door lock assembly LH (key
cylinder switch) D149. A. A/T selector lever
B. A/T device (park position switch)
M203
10. A. Sliding motor LH P4 (driver seat view), reclining motor LH P5, lifting
motor (front) P6, lifting motor (rear)
P7
B. Driver seat control unit P2, P3
C. Power seat switch LH P8 11. A. ADP steering switch M16
B.Tilt motor M68, M69
Function Description
Memory operation The front seat LH, steering wheel, pedals (accelerator, brake) and door mirrors move
to the stored driving position by pushing seat memory switch (1 or 2).
Entry/Exit-
ing function Exiting operation
At exit, the seat moves backward and the steering wheel raises. (Exiting position)
Entry operation At entry, the seat and steering wheel return from Exiting position to the previous driv-
ing position before the Exiting operation.
Keyfob interlock operation Perform memory operation, turnout operation and return operation by pressing key-
fob unlock button.
Auto operation temporary stop
conditions. When ignition switch is turned to START during seat memory switch operation and return
operation, seat memory switch operation and return operation is stopped.
Auto operation stop conditions.
When the vehicle speed becomes 7 km/h (4 MPH) or higher (memory switch operation
and entry operation).
When the setting switch, seat memory switch 1, or 2 are pressed.
When A/T selector lever is in any position other than P.
When the door mirror remote control switch is operated (when ignition switch turned to
ON).
When power seat switch turned ON.
When pedal adjusting switch turned ON.
When front seat sliding Entry/Exiting setting is OFF (entry/exiting operation).
OPERATED PORTION T2
Seat sliding Approx. 0.1 sec.
Seat reclining Same as above
Seat lifting (Front) Same as above
Seat lifting (Rear) Same as above
Page 2944 of 3383
AUTOMATIC DRIVE POSITIONERSE-13
C
DE
F
G H
J
K L
M A
B
SE
Revision: November 2009 2006 QX56
CANCEL OF FAIL-SAFE MODE
The mode is cancelled when the A/T selector lever is shifted to P position from any other position.
NOTE:
The front seat LH position and pedal adjustment functions (see the following table) operate simultaneously in
the order of priority.
*: In conjunction with sliding the seat, the door mirrors are positioned.
CAN Communication System DescriptionEIS004XG
Refer to LAN-26, "CAN COMMUNICATION" .
Steering wheel Same as above
Pedal adjust Same as above
OPERATED PORTION
T2
PriorityFunction PriorityFunction
1 Seat sliding, (door mirror LH/RH)* 4Seat reclining
2 Pedal 5Seat lifter-FR
3 Steering wheel 6Seat lifter-RR
Page 2959 of 3383
SE-28
AUTOMATIC DRIVE POSITIONER
Revision: November 20092006 QX56
Terminals and Reference Values for Automatic Drive Positioner Control UnitEIS004XL
31 L/Y Sensor ground—0
32 B Ground —0
33 L/B Battery power supply —Battery voltage
35 V/W Sliding motor FORWARD out-
put signal Sliding switch FORWARD opera-
tion (Motor operated)
Battery voltage
Other than above 0
36 Y/G Reclining motor FORWARD out-
put signal Reclining switch FORWARD oper-
ation (Motor operated)
Battery voltage
Other than above 0
37 BR Front lifting motor DOWN output
signal Front lifting switch DOWN opera-
tion (Motor operated)
Battery voltage
Other than above 0
38 B/W Rear lifting motor UP output sig-
nal Rear end lifting switch UP opera-
tion (Motor operated)
Battery voltage
Other than above 0
39 Y Rear lifting motor DOWN output
signal Rear end lifting switch DOWN
operation (Motor operated)
Battery voltage
Other than above 0
40 Y/R Battery power supply —Battery voltage
42 O/B Sliding motor BACKWARD out-
put signal Sliding switch BACKWARD oper-
ation (Motor operated)
Battery voltage
Other than above 0
44 Y/R Reclining motor BACKWARD
output signal Reclining switch BACKWARD
operation (Motor operated)
Battery voltage
Other than above 0
45 GR Front lifting motor UP output sig-
nal Front lifting switch UP operation
(Motor operated)
Battery voltage
Other than above 0
48 B/W Ground — 0
Te r m i n a l
Wire
Color Item
Condition Voltage (V)
(Approx.)
Te r m i n a l Wire
Color Item
Condition Voltage (V)
(Approx.)
1 W/G ADP steering switch TILT UP ADP steering switch in UP position
0
Other than above 5
2 LG Changeover switch RH signal Changeover switch in RH position
0
Other than above 5
3 Y/B Mirror switch UP signal Mirror switch in UP position
0
Other than above 5
4 V/W Mirror switch LEFT signal Mirror switch in LEFT position
0
Other than above 5
5R/B Mirror sensor (RH vertical) sig-
nal Mirror motor RH is operated UP or
DOWN Changes between 3.4 (close to
peak) 0.6 (close to valley)
6L/Y Mirror sensor (LH vertical) sig-
nal Mirror motor LH is operated UP or
DOWN Changes between 3.4 (close to
peak) 0.6 (close to valley)
7 Y/BR Tilt sensor input Tilt position TOP
2
Tilt position BOTTOM 4