wheel INFINITI QX56 2006 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2006, Model line: QX56, Model: INFINITI QX56 2006Pages: 3383, PDF Size: 51.76 MB
Page 2879 of 3383
RSU-40
REAR LOWER LINK & COIL SPRING
Revision: November 20092006 QX56
REAR LOWER LINK & COIL SPRINGPFP:551B0
Removal and Installation EES001HM
REMOVAL
1. Remove the wheel and tire assembly using power tool. Refer to WT-7, "Rotation" .
2. Use CONSULT-II "EXHAUST SOLENOID" active test to release the air pressure from the rear load level- ing air suspension system.
3. For removing the LH rear lower link and coil spring, remove the height sensor arm bracket bolt from the LH rear lower link.
4. Set a suitable jack to relieve the coil spring tension from the rear lower link.
WARNING:
Do not compress the coil spring when setting the jack.
5. Loosen the rear lower link adjusting bolt and nut connected to the rear suspension member, using power tool.
6. Remove the rear lower link bolt and nut from the knuckle using power tool.
7. Slowly lower the suitable jack to release the coil spring tension. Then remove the upper rubber seat, coil spring, and lower rubber seat from the rear lower link.
LEIA0080E
LEIA0077E
LEIA0009E
LEIA0077E
Page 2880 of 3383
REAR LOWER LINK & COIL SPRINGRSU-41
C
DF
G H
I
J
K L
M A
B
RSU
Revision: November 2009 2006 QX56
8. Remove the rear lower link adjusting bolt and nut from the rear
suspension member using power tool, then remove the rear
lower link.
INSPECTION AFTER REMOVAL
Check the coil spring and rubber seats for deformation, cracks, or other damage and replace if necessary.
INSTALLATION
Installation is in the reverse order of removal.
Tighten the nuts and bolts to specification. Refer to RSU-26, "Components" .
When installing the upper and lower rubber seats for the rear
coil springs, the arrow embossed on the rubber seats must point
out toward the wheel and tire assembly.
After installing the rear lower link and coil spring, check the
wheel alignment and adjust if necessary. Refer to RSU-28,
"Wheel Alignment Inspection" .
LEIA0009E
LEIA0076E
Page 2885 of 3383
RSU-46
HEIGHT SENSOR
Revision: November 20092006 QX56
INSTALLATION
Installation is in the reverse order of removal.
1. Start the engine.
2. Use CONSULT-II to perform "STANDARD HEIGHT LEVEL" work support function.
3. Using data monitor of CONSULT-II, verify "HEIGT CALC" is at 0 mm.
4. Check the vehicle height. Refer to RSU-49, "
Wheelarch Height (Unladen*1 )" . If vehicle height is not
within ± 10 mm (0 ± 0.39 in) of the specification, perform the initialization procedure. Refer to RSU-47,
"Initialization Procedure" .
Page 2887 of 3383
RSU-48
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: November 20092006 QX56
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Wheel AlignmentEES001HT
Ball JointEES001HU
Camber
Degree minute (decimal degree)Minimum
0° 0 ′ (0 °)
Nominal - 0° 30 ′ (-0.5 °)
Maximum - 1° 0 ′ (-1.0 °)
Cross camber 0° 45′ (0.75 °)
Toe-in Distance (A - B)
Minimum
0 mm (0 in)
Nominal 3.3 mm (0.130 in)
Maximum 6.6 mm (0.260 in)
Cross toe 2 mm (0.079 in)
Angle (left, right)
Degree minute (decimal degree) Minimum
0° 0 ′ (0 °)
Nominal 0° 7 ′ (0.11 °)
Maximum 0° 14′ (0.22 °)
Cross toe 0° 8 ′ (0.14 °)
SFA234AC
Swinging force (measurement point: cotter pin hole of ball stud) “A ” 11.4 - 145.5 N (1.16 - 14.8 kg, 2.56 - 32.7 lb)
Turning torque “B ” 0.5 - 6.4 N·m (0.06 - 0.65 kg-m, 5 - 56 in-lb)
Vertical end play “C ” 0 mm (0 in)
SFA858A
Page 2888 of 3383
SERVICE DATA AND SPECIFICATIONS (SDS)RSU-49
C
DF
G H
I
J
K L
M A
B
RSU
Revision: November 2009 2006 QX56
Wheelarch Height (Unladen*1 )EES001HV
Unit: mm (in)
*1: Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
*2: Verify the vehicle height. If vehicle height is not within ± 10 mm (0.39 in) of the specification, perform the control unit initialization pro-
cedure. Refer to RSU-47, "
Initialization Procedure" .
Suspension type
Air leveling*
2
Applied model2WD 4WD
Front wheelarch height (Hf) 913
(35.94) 931
(36.65)
Rear wheelarch height (Hr) 912
(35.91) 932
(36.69)
LEIA0085E
Page 2932 of 3383
SE-1
SEAT
I BODY
CONTENTS
C
DE
F
G H
J
K L
M
SECTION
A
B
SE
Revision: November 2009 2006 QX56
PRECAUTIONS .....................................................
..... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 3
Precautions for Work ........................................... ..... 3
PREPARATION ...................................................... ..... 4
Special Service Tool ............................................ ..... 4
Commercial Service Tool .................................... ..... 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5 CUSTOMER INTERVIEW ................................ ..... 5
DUPLICATE THE NOISE AND TEST DRIVE .. ..... 6
CHECK RELATED SERVICE BULLETINS ...... ..... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ................................................. ..... 6
REPAIR THE CAUSE ...................................... ..... 6
CONFIRM THE REPAIR .................................. ..... 7
Generic Squeak and Rattle Troubleshooting ...... ..... 7
INSTRUMENT PANEL ..................................... ..... 7
CENTER CONSOLE ........................................ ..... 7
DOORS ............................................................ ..... 7
TRUNK ............................................................. ..... 8
SUNROOF/HEADLINING ................................ ..... 8
OVERHEAD CONSOLE (FRONT AND REAR) ..... 8
SEATS .............................................................. ..... 8
UNDERHOOD .................................................. ..... 8
Diagnostic Worksheet ......................................... ..... 9
AUTOMATIC DRIVE POSITIONER ....................... ....11
Component Parts And Harness Connector Location .... 11
System Description ............................................. ... 12
FAIL-SAFE MODE ........................................... ... 12
CANCEL OF FAIL-SAFE MODE ...................... ... 13
CAN Communication System Description ........... ... 13
Schematic ........................................................... ... 14
Wiring Diagram — AUT/DP — ............................ ... 16
Terminals and Reference Values for BCM .......... ... 26
Terminals and Reference Values for Driver Seat
Control Unit ......................................................... ... 26
Terminals and Reference Values for Automatic Drive Positioner Control Unit ...............................
... 28
Work Flow ............................................................... 30
Preliminary Check ............................................... ... 31
SETTING CHANGE FUNCTION ...................... ... 31
POWER SUPPLY AND GROUND CIRCUIT
INSPECTION ................................................... ... 31
CONSULT-II Function (AUTO DRIVE POS.) ....... ... 34
CONSULT-II INSPECTION PROCEDURE ....... ... 34
SELF-DIAGNOSIS RESULTS .......................... ... 36
DATA MONITOR .............................................. ... 37
ACTIVE TEST ..................................................... 38
CAN Communication Inspection Using CONSULT-
II (Self-Diagnosis) ................................................ ... 38
Symptom Chart ....................................................... 38
Sliding Motor Circuit Inspection ........................... ... 40
Reclining Motor LH Circuit Inspection ................. ... 41
Lifting Motor (Front) Circuit Inspection ................ ... 42
Lifting Motor (Rear) Circuit Inspection ................. ... 44
Pedal Adjusting Motor Circuit Inspection ............. ... 45
Mirror Motor LH Circuit Check ................................ 46
Mirror Motor RH Circuit Check ............................ ... 48
Steering Wheel Tilt Circuit Inspection .................. ... 49
Sliding Sensor Circuit Inspection ......................... ... 51
Reclining Sensor Circuit Inspection ..................... ... 52
Lifting Sensor (Front) Circuit Inspection .............. ... 53
Lifting Sensor (Rear) Circuit Inspection ............... ... 54
Pedal Adjusting Sensor Circuit Inspection ........... ... 55
Mirror Sensor LH Circuit Check ........................... ... 56
Mirror Sensor RH Circuit Check ............................. 57
Steering Wheel Tilt Sensor Circuit Inspection ..... ... 59
Sliding Switch Circuit Inspection .......................... ... 61
Reclining Switch Inspection ................................. ... 62
Lifting Switch (Front) Circuit Inspection ............... ... 64
Lifting Switch (Rear) Circuit Inspection ................ ... 65
Power Seat Switch Ground Inspection ................ ... 66
Pedal Adjusting Switch Circuit Inspection ........... ... 67
Door Mirror Remote Control Switch (Changeover
Switch) Circuit Check ............................................. 69
Door Mirror Remote Control Switch (Mirror Switch)
Circuit Check ....................................................... ... 70
Page 2933 of 3383
SE-2Revision: November 20092006 QX56
Door Mirror Remote Control Switch Ground Circuit
Inspection ............................................................
... 72
Seat Memory Switch Circuit Inspection ............... ... 72
Seat Memory Indicator Lamp Circuit Inspection .. ... 74
Door Mirror Sensor Power Supply and Ground Cir-
cuit inspection ...................................................... ... 75
A/T Device (Park Position Switch) Circuit Inspection ... 76
Steering Wheel Tilt Switch Circuit Inspection ...... ... 77
Front Door Switch LH Circuit Inspection .............. ... 79
UART Communication Line Circuit Inspection ..... ... 80
Removal and Installation ..................................... ... 82
POWER SEAT ........................................................ ... 83
Wiring Diagram — SEAT — for Passenger Seat . ... 83
HEATED SEAT ....................................................... ... 84
Description ........................................................... ... 84
Schematic ............................................................ ... 85
Wiring Diagram — HSEAT — .............................. ... 86
FRONT SEAT ......................................................... ... 91
Removal and Installation ..................................... ... 91
REMOVAL ........................................................ ... 94INSTALLATION .................................................
... 94
Disassembly and Assembly ................................. ... 94
SEATBACK TRIM AND PAD ............................ ... 94
REMOVAL OF SEATBACK ASSEMBLY .......... ... 96
INSTALLATION OF SEATBACK ASSEMBLY .. ... 96
SEAT CUSHION TRIM AND PAD (DRIVER) OR
SEAT CUSHION ASSEMBLY (PASSENGER) .. ... 96
SECOND SEAT ...................................................... ... 98
Removal and Installation ...................................... ... 98
SECOND ROW OUTBOARD ........................... ... 98
SECOND ROW CENTER ................................. ... 98
Disassembly and Assembly ................................. ... 99
THIRD SEAT ........................................................... .105
LH Side Seat ........................................................ .105
REMOVAL ......................................................... .105
INSTALLATION ................................................. .105
DISASSEMBLY AND ASSEMBLY .................... .106
RH Side Seat ....................................................... .107
REMOVAL ......................................................... .107
INSTALLATION ................................................. .108
DISASSEMBLY AND ASSEMBLY .................... .109
Page 2943 of 3383
SE-12
AUTOMATIC DRIVE POSITIONER
Revision: November 20092006 QX56
System DescriptionEIS004XE
Refer to Owner's Manual for Automatic Drive Positioner system operating instructions.
The settings (ON/OFF) of the automatic sliding seat (Entry/Exiting operation) at entry/exit can be changed
as desired, using the display unit in the center of the instrument panel. The set content is transmitted by
CAN communication, from display control unit to driver seat control unit.
Using CONSULT-ll, the seat slide amount at entry/exit setting can be changed.
NOTE:
Disconnecting the battery erases the stored memory.
After connecting the battery, insert the key into the ignition cylinder and turn the front door switch LH ON (open) →OFF (close) →ON
(open), the Entry/Exiting function becomes possible.
After Exiting operation is carried out, return operation can be operated.
NOTE:
During automatic operation, if the ignition switch is turned ON →START, the automatic operation is suspended. When the ignition switch
returns to ON, it resumes.
FAIL-SAFE MODE
When any manual and automatic operations are not performed, if any motor operations of seats or pedals are
detected for T2 or more, status is judged “Output error ”.
7. Pedal adjusting switch M96 8. A. Door mirrror LH D4, RH D107
B. Front door switch LH B8
C. Front door lock assembly LH (key
cylinder switch) D149. A. A/T selector lever
B. A/T device (park position switch)
M203
10. A. Sliding motor LH P4 (driver seat view), reclining motor LH P5, lifting
motor (front) P6, lifting motor (rear)
P7
B. Driver seat control unit P2, P3
C. Power seat switch LH P8 11. A. ADP steering switch M16
B.Tilt motor M68, M69
Function Description
Memory operation The front seat LH, steering wheel, pedals (accelerator, brake) and door mirrors move
to the stored driving position by pushing seat memory switch (1 or 2).
Entry/Exit-
ing function Exiting operation
At exit, the seat moves backward and the steering wheel raises. (Exiting position)
Entry operation At entry, the seat and steering wheel return from Exiting position to the previous driv-
ing position before the Exiting operation.
Keyfob interlock operation Perform memory operation, turnout operation and return operation by pressing key-
fob unlock button.
Auto operation temporary stop
conditions. When ignition switch is turned to START during seat memory switch operation and return
operation, seat memory switch operation and return operation is stopped.
Auto operation stop conditions.
When the vehicle speed becomes 7 km/h (4 MPH) or higher (memory switch operation
and entry operation).
When the setting switch, seat memory switch 1, or 2 are pressed.
When A/T selector lever is in any position other than P.
When the door mirror remote control switch is operated (when ignition switch turned to
ON).
When power seat switch turned ON.
When pedal adjusting switch turned ON.
When front seat sliding Entry/Exiting setting is OFF (entry/exiting operation).
OPERATED PORTION T2
Seat sliding Approx. 0.1 sec.
Seat reclining Same as above
Seat lifting (Front) Same as above
Seat lifting (Rear) Same as above
Page 2944 of 3383
AUTOMATIC DRIVE POSITIONERSE-13
C
DE
F
G H
J
K L
M A
B
SE
Revision: November 2009 2006 QX56
CANCEL OF FAIL-SAFE MODE
The mode is cancelled when the A/T selector lever is shifted to P position from any other position.
NOTE:
The front seat LH position and pedal adjustment functions (see the following table) operate simultaneously in
the order of priority.
*: In conjunction with sliding the seat, the door mirrors are positioned.
CAN Communication System DescriptionEIS004XG
Refer to LAN-26, "CAN COMMUNICATION" .
Steering wheel Same as above
Pedal adjust Same as above
OPERATED PORTION
T2
PriorityFunction PriorityFunction
1 Seat sliding, (door mirror LH/RH)* 4Seat reclining
2 Pedal 5Seat lifter-FR
3 Steering wheel 6Seat lifter-RR
Page 2962 of 3383
AUTOMATIC DRIVE POSITIONERSE-31
C
DE
F
G H
J
K L
M A
B
SE
Revision: November 2009 2006 QX56
Preliminary CheckEIS004XN
SETTING CHANGE FUNCTION
The settings of the automatic driving positioner system can be changed, using CONSULT-II and the display in
the center of the instrument panel.
×: Applicable –: Not applicable
It is possible to set sliding front seat for entry/exit of vehicle by pressing set switch.
*: Setting of sliding front seat for entry/exit of vehicle is ON at factory-shipment. But if custom settings are reset, setting turns OFF.
NOTE:
After the setting is registered, the new setting is effective, even if the battery is disconnected.
POWER SUPPLY AND GROUND CIRCUIT INSPECTION
1. CHECK BCM FUSES AND FUSIBLE LINK
Check if any of the following fuses for the BCM are blown.
NOTE:
Refer to SE-11, "
Component Parts And Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
65, "ELECTRICAL UNITS LOCATION" .
Setting item ContentCONSULT
–II
(WORK SUPPORT) Display unitDefault
setting Factory
setting
SEAT SLIDE
VOLUME SET The distance at exiting opera-
tion can be selected from the
following 3 modes. 40mm
—××
80mm ——
150mm ——
Sliding Front Seat and
Steering Wheel Raise
When Entry/ Exiting
Vehicle The seat sliding and steering
wheel raise turnout and return
at entry/exit can be selected:
ON (operated)
–OFF (not
operated) ON
ON: Indicator lamp ON —×
OFF OFF: Indicator lamp OFF ×—
Reset custom settings* All settings to default. —Default: Setting button
ON ——
Content
Setting change operation Indicator LEDs
The seat sliding and steering
wheel raise turnout and return
at entry/exit can be operated. Press the set switch for more than 10 seconds Blinking twice
The seat sliding and steering
wheel raise turnout and return
at entry/exit can be not oper-
ated. Blinking once
Unit
Power source Fuse No.
BCM Battery power supply
f (50A)
ON or START power supply 59 (10A)
ACC or ON power supply 4 (10A)