battery location INFINITI QX56 2006 Factory User Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2006, Model line: QX56, Model: INFINITI QX56 2006Pages: 3383, PDF Size: 51.76 MB
Page 2109 of 3383
GI-18
HOW TO USE THIS MANUAL
Revision: November 20092006 QX56
Optional Splice
DESCRIPTION
SGI942
Num-
ber Item
Description
1 Power condition
This shows the condition when the system receives battery positive voltage (can be oper-
ated).
2 Fusible link
The double line shows that this is a fusible link.
The open circle shows current flow in, and the shaded circle shows current flow out.
3 Fusible link/fuse loca-
tion
This shows the location of the fusible link or fuse in the fusible link or fuse box. For arrange-
ment, refer to PG section, POWER SUPPLY ROUTING.
4Fuse
The single line shows that this is a fuse.
The open circle shows current flow in, and the shaded circle shows current flow out.
5 Current rating
This shows the current rating of the fusible link or fuse.
6 Connectors
This shows that connector E3 is female and connector M1 is male.
The G/R wire is located in the 1A terminal of both connectors.
Terminal number with an alphabet (1A, 5B, etc.) indicates that the connector is SMJ connec-
tor. Refer to PG section, SMJ (SUPER MULTIPLE JUNCTION).
7 Optional splice
The open circle shows that the splice is optional depending on vehicle application.
8 Splice
The shaded circle shows that the splice is always on the vehicle.
9 Page crossing
This arrow shows that the circuit continues to an adjacent page.
The A will match with the A on the preceding or next page.
10 Common connector
The dotted lines between terminals show that these terminals are part of the same connector.
11 Option abbreviation
This shows that the circuit is optional depending on vehicle application.
12 Relay
This shows an internal representation of the relay. For details, refer to PG section, STAN-
DARDIZED RELAY.
13 Connectors
This shows that the connector is connected to the body or a terminal with bolt or nut.
Page 2182 of 3383
POWER WINDOW SYSTEMGW-37
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
BCM Power Supply and Ground Circuit CheckEIS005XY
1. CHECK FUSE AND FUSIBLE LINK
Check 10A fuse (No. 4, located in the fuse block (J/B)]
Check 10A fuse (No. 59, located in the fuse and relay box)
Check 50A fusible link (letter f , located in the fuse and fusible link box)
NOTE:
Refer to GW-15, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
3, "PRECAUTIONS" .
2. CHECK BCM POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace the harness.
3. CHECK GROUND CIRCUIT
Check continuity between BCM connector M20 terminal 67 and
ground.
OK or NG
OK >> Power supply and ground circuit is OK.
NG >> Repair or replace harness.
Connector Terminals
Power
source Condition Voltage (V)
(Approx.)
(+) (-)
M20 70 Ground Battery
power
supply Ignition
switch
OFF Battery voltage
M18 38 Ground
Ignition
power
supply Ignition
switch
ON or
START Battery voltage
11 Ground ACC
power
supply Ignition
switch
ACC or ON Battery voltage
LIIA0995E
67 - Ground
: Continuity should exist.
LIIA0915E
Page 2229 of 3383
![INFINITI QX56 2006 Factory User Guide GW-84
REAR WINDOW DEFOGGER
Revision: November 20092006 QX56
BCM Power Supply and Ground Circuit CheckEIS005YW
1. CHECK FUSES AND FUSIBLE LINK
Check 10A fuse (No. 8, located in the fuse block (J/B)]](/img/42/57028/w960_57028-2228.png "INFINITI QX56 2006 Factory User Guide GW-84
REAR WINDOW DEFOGGER
Revision: November 20092006 QX56
BCM Power Supply and Ground Circuit CheckEIS005YW
1. CHECK FUSES AND FUSIBLE LINK
Check 10A fuse (No. 8, located in the fuse block (J/B)]")
GW-84
REAR WINDOW DEFOGGER
Revision: November 20092006 QX56
BCM Power Supply and Ground Circuit CheckEIS005YW
1. CHECK FUSES AND FUSIBLE LINK
Check 10A fuse (No. 8, located in the fuse block (J/B)]
Check 10A fuse (No. 59, located in the fuse and relay box)
Check 50A fusible link (letter f , located in the fuse and fusible link box)
NOTE:
Refer to GW-74, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between BCM connector M18, M20 terminals 38, 70
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check continuity between BCM connector M20 terminal 67 and ground.
OK or NG
OK >> BCM power supply and ground circuit is OK.
NG >> Repair or replace harness. 70 - Ground
: Battery voltage
38 - Ground : Battery voltage
LIIA0914E
67 - Ground : Continuity should exist.
LIIA0915E
Page 2231 of 3383
GW-86
REAR WINDOW DEFOGGER
Revision: November 20092006 QX56
3. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M18 terminal 9 and ground.
OK or NG
OK >> Replace front air control. Refer to ATC-144, "FRONT
AIR CONTROL" .
NG >> Replace BCM. Refer to BCS-20, "
BCM" .
Rear Window Defogger Circuit CheckEIS0062Z
1. CHECK FUSES
Check if any of the following fuses in IPDM E/R are blown.
NOTE:
Refer to GW-74, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse, refer to GW-
74, "Component Parts and Harness Connector Location" .
2. CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear window defogger.
3. Turn ignition switch ON.
4. Check voltage between rear window defogger connector D406 terminal + and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4. 9 - Ground
: Approx. 5
WIIA0523E
COMPONENT PARTS AMPEREFUSE NO.
IPDM E/R 15A46
IPDM E/R 15A47
ConnectorTerminals
ConditionVoltage (V)
(Approx.)
(+) (-)
D406 + Ground Rear window defogger
switch ON.
Battery voltage
Rear window defogger
switch OFF. 0
LIIA0655E
Page 2232 of 3383
REAR WINDOW DEFOGGERGW-87
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
3. CHECK REAR WINDOW DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between rear window defogger connector D604 terminal - and ground.
OK or NG
OK >> Check filament. Refer to GW-91, "Filament Check" .
If filament is OK.
Check the condition of the harness and the connector.
If filament is NG.
Repair filament.
NG >> Repair or replace harness.
4. CHECK REAR WINDOW DEFOGGER RELAY OUTPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R connector E124 terminal 60 and ground.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-30, "Removal and Installation of IPDM E/R" .
NG >> Repair or replace harness.
Door Mirror Defogger Power Supply Circuit CheckEIS005Z0
1. CHECK FUSE
Check if any of the following fuses in fuse block (J/B) are blown.
NOTE:
Refer to GW-74, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
GW-74, "
Component Parts and Harness Connector Location" .
- - Ground
: Continuity should exist.
LIIA0409E
ConnectorTerminals
ConditionVoltage (V)
(Approx.)
(+) (-)
E124 60 Ground Rear window defogger
switch ON.
Battery voltage
Rear window defogger
switch OFF. 0
WIIA0525E
COMPONENT PARTS
AMPEREFUSE NO.
IPDM E/R 15A43
Page 2408 of 3383
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
DE
F
G H
I
J
L
M
SECTION
A
B
LT
Revision: November 2009 2006 QX56
PRECAUTIONS .....................................................
..... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 4
General precautions for service operations ........ ..... 4
HEADLAMP (FOR USA) ....................................... ..... 5
Component Parts and Harness Connector Location ..... 5
System Description ............................................. ..... 5
OUTLINE .......................................................... ..... 5
XENON HEADLAMP ........................................ ..... 6
BATTERY SAVER CONTROL ......................... ..... 7
AUTO LIGHT OPERATION .............................. ..... 7
VEHICLE SECURITY SYSTEM (PANIC ALARM) ..... 7
CAN Communication System Description ........... ..... 7
Schematic ........................................................... ..... 8
Wiring Diagram — H/LAMP — ............................ ..... 9
Terminals and Reference Values for BCM .......... ... 13
Terminals and Reference Values for IPDM E/R .. ... 14
How to Proceed With Trouble Diagnosis ............. ... 14
Preliminary Check ............................................... ... 14
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 14
CONSULT-II Function (BCM) .............................. ... 16
CONSULT-II OPERATION ............................... ... 16
WORK SUPPORT ............................................ ... 17
DATA MONITOR .............................................. ... 17
ACTIVE TEST .................................................. ... 18
SELF-DIAGNOSTIC RESULTS ....................... ... 18
CONSULT-II Function (IPDM E/R) ...................... ... 19
CONSULT-II OPERATION ............................... ... 19
DATA MONITOR .............................................. ... 20
ACTIVE TEST .................................................. ... 20
Headlamp HI Does Not Illuminate (Both Sides) .. ... 21
Headlamp HI Does Not Illuminate (One Side) .... ... 23
High Beam Indicator Lamp Does Not Illuminate . ... 24
Headlamp LO Does Not Illuminate (Both Sides) . ... 24
Headlamp LO Does Not Illuminate (One Side) ... ... 26
Headlamps Do Not Turn OFF ............................. ... 27
Aiming Adjustment .............................................. ... 29
HEADLAMP AIMING ........................................ ... 29Bulb Replacement ...............................................
... 30
HEADLAMP (OUTER SIDE), FOR LOW BEAM ... 30
HEADLAMP (INNER SIDE), FOR HIGH BEAM ... 31
FRONT PARKING LAMP (INNER OR OUTER) ... 31
SIDE MARKER LAMP (FRONT) ......................... 31
Removal and Installation ..................................... ... 31
FRONT COMBINATION LAMP ASSEMBLY .... ... 31
INSTALLATION ................................................ ... 32
Disassembly and Assembly ................................. ... 32
FRONT COMBINATION LAMP ASSEMBLY .... ... 32
DISASSEMBLY ................................................ ... 32
ASSEMBLY ...................................................... ... 32
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - ............................................................... ... 33
Component Parts and Harness Connector Location ... 33
System Description .............................................. ... 34
OUTLINE .......................................................... ... 34
DAYTIME LIGHT OPERATION ........................ ... 34
COMBINATION SWITCH READING FUNCTION ... 34
AUTO LIGHT OPERATION .............................. ... 35
CAN Communication System Description ........... ... 35
Schematic ............................................................ ... 36
Wiring Diagram — DTRL — ................................ ... 37
Terminals and Reference Values for BCM ........... ... 41
How to Proceed With Trouble Diagnosis ............. ... 42
Preliminary Check ............................................... ... 42
CHECK BCM CONFIGURATION ..................... ... 42
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT .......................................... ... 42
INSPECTION PARKING BRAKE SWITCH CIR-
CUIT ................................................................. ... 43
CONSULT-II Functions ........................................ ... 44
Daytime Light Control Does Not Operate Properly
(Normal Headlamps Operate Properly) ............... ... 44
Aiming Adjustment ............................................... ... 46
Bulb Replacement ............................................... ... 46
Removal and Installation ..................................... ... 46
Disassembly and Assembly ................................. ... 46
AUTO LIGHT SYSTEM .......................................... ... 47
Component Parts and Harness Connector Location ... 47
Page 2409 of 3383
LT-2Revision: November 20092006 QX56
System Description ..............................................
... 48
OUTLINE .......................................................... ... 48
COMBINATION SWITCH READING FUNCTION ... 48
EXTERIOR LAMP BATTERY SAVER CONTROL ... 48
DELAY TIMER FUNCTION .............................. ... 48
CAN Communication System Description ........... ... 48
Major Components and Functions ....................... ... 48
Schematic ............................................................ ... 49
Wiring Diagram — AUTO/L — ............................. ... 50
Terminals and Reference Values for BCM ........... ... 53
Terminals and Reference Values for IPDM E/R ... ... 54
How to Proceed With Trouble Diagnosis ............. ... 55
Preliminary Check ............................................... ... 55
SETTING CHANGE FUNCTIONS .................... ... 55
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 55
CONSULT-II Function (BCM) ............................... ... 57
CONSULT-II OPERATION ................................ ... 57
WORK SUPPORT ............................................ ... 58
DATA MONITOR ............................................... ... 58
ACTIVE TEST .................................................. ... 59
SELF-DIAGNOSTIC RESULTS ........................ ... 59
CONSULT-II Function (IPDM E/R) ....................... ... 60
CONSULT-II OPERATION ................................ ... 60
DATA MONITOR ............................................... ... 61
ACTIVE TEST .................................................. ... 61
Trouble Diagnosis Chart by Symptom ................. ... 62
Lighting Switch Inspection ................................... ... 62
Optical Sensor System Inspection ....................... ... 63
Optical Sensor ..................................................... ... 64
REMOVAL AND INSTALLATION ...................... ... 64
HEADLAMP AIMING CONTROL ........................... ... 65
System Description .............................................. ... 65
Wiring Diagram — H/AIM — ................................ ... 66
Headlamp Aiming Switch ..................................... ... 68
REMOVAL AND INSTALLATION ...................... ... 68
Switch Circuit Inspection ..................................... ... 68
FRONT FOG LAMP ............................................... ... 69
Component Parts and Harness Connector Location ... 69
System Description .............................................. ... 69
OUTLINE .......................................................... ... 69
COMBINATION SWITCH READING FUNCTION ... 70
EXTERIOR LAMP BATTERY SAVER CONTROL ... 70
CAN Communication System Description ........... ... 70
Wiring Diagram — F/FOG — ............................... ... 71
Terminals and Reference Values for BCM ........... ... 73
Terminals and Reference Values for IPDM E/R ... ... 74
How to Proceed With Trouble Diagnosis ............. ... 74
Preliminary Check ............................................... ... 75
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 75
CONSULT-II Functions ........................................ ... 76
Front Fog Lamps Do Not Illuminate (Both Sides) ... 76
Front Fog Lamp Does Not Illuminate (One Side) ... 77
Aiming Adjustment ............................................... ... 78
Bulb Replacement ............................................... ... 79
FRONT FOG LAMP .......................................... ... 79INSTALLATION ................................................
... 79
Removal and Installation ...................................... ... 79
FRONT FOG LAMP .......................................... ... 79
INSTALLATION ................................................ ... 79
TURN SIGNAL AND HAZARD WARNING LAMPS ... 80
Component Parts and Harness Connector Location ... 80
System Description .............................................. ... 80
OUTLINE .......................................................... ... 80
TURN SIGNAL OPERATION ............................ ... 80
HAZARD LAMP OPERATION .......................... ... 81
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION ................................................................. ... 82
COMBINATION SWITCH READING FUNCTION ... 82
CAN Communication System Description ........... ... 82
Schematic ............................................................ ... 83
Wiring Diagram — TURN — ................................ ... 84
Terminals and Reference Values for BCM ........... ... 87
How to Proceed With Trouble Diagnosis ............. ... 88
Preliminary Check ................................................ ... 89
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. ... 89
CONSULT-II Function (BCM) ............................... ... 90
CONSULT-II OPERATION ................................ ... 90
DATA MONITOR ............................................... ... 91
ACTIVE TEST ................................................... ... 91
Front Turn Signal Lamp Does Not Operate ......... ... 92
Door Mirror Turn Signal Lamp Does Not Operate ... 93
Rear Turn Signal Lamp Does Not Operate .......... ... 94
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamps Operate ......................................... ... 95
Turn Signal Indicator Lamp Does Not Operate .... ... 96
Bulb Replacement ................................................ ... 97
TURN SIGNAL LAMP (FRONT) ....................... ... 97
TURN SIGNAL LAMP (REAR) .......................... ... 97
Removal and Installation ...................................... ... 97
FRONT TURN SIGNAL LAMP .......................... ... 97
REAR TURN SIGNAL LAMP ............................ ... 97
LIGHTING AND TURN SIGNAL SWITCH ............. ... 98
Removal and Installation ...................................... ... 98
REMOVAL ........................................................ ... 98
INSTALLATION ................................................ ... 98
HAZARD SWITCH .................................................. ... 99
Removal and Installation ...................................... ... 99
REMOVAL ........................................................ ... 99
INSTALLATION ................................................ ... 99
COMBINATION SWITCH ....................................... .100
Wiring Diagram — COMBSW — ......................... .100
Combination Switch Reading Function ................ .101
CONSULT-II Function (BCM) ............................... .101
CONSULT-II OPERATION ................................ .101
DATA MONITOR ............................................... .102
Combination Switch Inspection ............................ .103
Removal and Installation ...................................... .105
Switch Circuit Inspection ...................................... .105
STOP LAMP ........................................................... .106
System Description .............................................. .106
Wiring Diagram — STOP/L — ............................. .107
Bulb Replacement ................................................ .108
HIGH-MOUNTED STOP LAMP ........................ .108
Page 2410 of 3383
LT-3
C
DE
F
G H
I
J
L
M A
B
LT
Revision: November 2009 2006 QX56
STOP LAMP .....................................................
. 108
Removal and Installation ..................................... . 108
HIGH_MOUNTED STOP LAMP ...................... . 108
STOP LAMP ..................................................... . 108
BACK-UP LAMP ................................................... . 109
Wiring Diagram — BACK/L — ............................ . 109
Bulb Replacement ............................................... .. 110
BACK-UP LAMP .............................................. .. 110
INSTALLATION ................................................ .. 110
Removal and Installation ..................................... .. 110
BACK-UP LAMP .............................................. .. 110
PARKING, LICENSE PLATE AND TAIL LAMPS .. .. 111
Component Parts and Harness Connector Location . . 111
System Description ............................................. . . 111
OPERATION BY LIGHTING SWITCH ............. .. 112
COMBINATION SWITCH READING FUNCTION .. 112
EXTERIOR LAMP BATTERY SAVER CONTROL .. 112
CAN Communication System Description ........... .. 112
Schematic ........................................................... .. 113
Wiring Diagram — TAIL/L — ................................. 114
Terminals and Reference Values for BCM .......... .. 117
Terminals and Reference Values for IPDM E/R .. .. 118
How to Proceed With Trouble Diagnosis ............. .. 118
Preliminary Check ............................................... .. 118
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. .. 118
CONSULT-II Functions ........................................ .. 119
Parking, License Plate and/or Tail Lamps Do Not
Illuminate ............................................................. . 120
Parking, License Plate and Tail Lamps Do Not Turn
OFF (After Approx. 10 Minutes) .......................... . 123
Bulb Replacement ............................................... . 124
FRONT PARKING LAMP ................................. . 124
LICENSE PLATE LAMP ................................... . 124
SIDE MARKER LAMP (FRONT) ...................... . 124
TAIL LAMP ....................................................... . 124
Removal and Installation ..................................... . 124
FRONT PARKING LAMP ................................. . 124
LICENSE PLATE LAMP ................................... . 124
INSTALLATION ................................................ . 124
SIDE MARKER LAMP (REAR) ........................ . 124
TAIL LAMP ....................................................... . 124
REAR COMBINATION LAMP ............................... . 125
Bulb Replacement ............................................... . 125
SIDE MARKER LAMP (REAR) ........................ . 125
TAIL LAMP ....................................................... . 125
TURN SIGNAL ................................................. . 125
STOP LAMP ..................................................... . 125
INSTALLATION ................................................ . 125
Removal and Installation ..................................... . 125
REAR COMBINATION LAMP .......................... . 125
TRAILER TOW ...................................................... . 126Component Parts and Harness Connector Location
.126
System Description .............................................. .126
TRAILER TAIL LAMP OPERATION ................. .127
TRAILER BRAKE, TURN SIGNAL AND HAZARD
LAMP OPERATION .......................................... .127
TRAILER BRAKE OPERATION ....................... .128
TRAILER POWER SUPPLY OPERATION ....... .128
Schematic ............................................................ .129
Wiring Diagram — T/TOW — .............................. .130
INTERIOR ROOM LAMP ....................................... .134
Component Parts and Harness Connector Location .134
System Description .............................................. .135
POWER SUPPLY AND GROUND ................... .135
SWITCH OPERATION ..................................... .136
ROOM LAMP TIMER OPERATION ................. .136
INTERIOR LAMP BATTERY SAVER CONTROL .137
Schematic ............................................................ .138
Wiring Diagram — INT/L — ................................. .140
Terminals and Reference Values for BCM ........... .147
How to Proceed With Trouble Diagnosis ............. .148
Preliminary Check ............................................... .148
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT .......................................... .148
CONSULT-II Function (BCM) .............................. .149
CONSULT-II OPERATION ................................ .149
WORK SUPPORT ............................................ .150
DATA MONITOR .............................................. .150
ACTIVE TEST .................................................. .151
Room/Map Lamp Control Does Not Operate ...... .151
Personal Lamp Control Does Not Operate (Room/
Map Lamps Operate) ........................................... .153
All Step/Foot/Puddle Lamps Do Not Operate ...... .154
All Interior Room Lamps Do Not Operate ............ .155
Ignition Keyhole Illumination Control Does Not
Operate ................................................................ .155
ILLUMINATION ...................................................... .157
Component Parts and Harness Connector Location .157
System Description .............................................. .157
ILLUMINATION OPERATION BY LIGHTING
SWITCH ........................................................... .158
EXTERIOR LAMP BATTERY SAVER CONTROL .159
CAN Communication System Description ........... .159
Schematic ............................................................ .160
Wiring Diagram — ILL — ..................................... .163
Removal and Installation of Illumination Control
Switch .................................................................. .174
REMOVAL ........................................................ .174
INSTALLATION ................................................ .174
BULB SPECIFICATIONS ....................................... .175
Headlamp ............................................................ .175
Exterior Lamp ...................................................... .175
Interior Lamp/Illumination .................................... .175
Page 2533 of 3383
LT-126
TRAILER TOW
Revision: November 20092006 QX56
TRAILER TOWPFP:93020
Component Parts and Harness Connector LocationEKS00BB1
System DescriptionEKS00BB2
Power is supplied at all times
to ignition relay, located in the IPDM E/R (intelligent power distribution module engine room), and
through 50A fusible link (letter f , located in the fuse and fusible link box)
to BCM (body control module) terminal 70, and
through 10A fuse (No. 32, located in the IPDM E/R)
1. Fuse and fusible link box2. IPDM E/R fuse layout 3. Fuse and relay box
4. IPDM E/R E118, E119, E120, E121, E122, E123, E124 5. A. Steering column
B. Data link connector M22
C. BCM M18, M19, M20
(View with instrument lower panel
LH removed) 6. A. Trailer turn relay LH E156
B. Battery
C. Trailer tow relay 2 E140
D. Trailer turn relay RH E157
7. A. Trailer tow relay 1 M51 B. Electric brake (pre-wiring) M76
(View with instrument lower panel
LH removed) 8. Trailer connector C2
9. Combination switch (lighting switch)
M28
WKIA4616E
Page 2642 of 3383
PG-1
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS
K ELECTRICAL
CONTENTS
C
DE
F
G H
I
J
L
M
SECTION
A
B
PG
Revision: November 2009 2006 QX56
PRECAUTIONS .....................................................
..... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 3
POWER SUPPLY ROUTING CIRCUIT ................. ..... 4
Schematic ........................................................... ..... 4
Wiring Diagram — POWER — ................................. 6 BATTERY POWER SUPPLY — IGNITION SW.
IN ANY POSITION ................................................ 6
ACCESSORY POWER SUPPLY — IGNITION
SW. IN ACC OR ON ............................................. 11
IGNITION POWER SUPPLY — IGNITION SW.
IN ON ............................................................... ... 12
IGNITION POWER SUPPLY — IGNITION SW.
IN ON AND/OR START .................................... ... 13
Fuse .................................................................... ... 17
Fusible Link ......................................................... ... 17
Circuit Breaker (Built Into BCM) .......................... ... 17
IPDM E/R (INTELLIGENT POWER DISTRIBUTION
MODULE ENGINE ROOM) ................................... ... 18
System Description ............................................. ... 18
SYSTEMS CONTROLLED BY IPDM E/R ........ ... 18
CAN COMMUNICATION LINE CONTROL ...... ... 18
IPDM E/R STATUS CONTROL ........................ ... 19
CAN Communication System Description ........... ... 19
Function of Detecting Ignition Relay Malfunction ... 19
CONSULT-II Function IPDM E/R ......................... ... 20
CONSULT-II BASIC OPERATION ................... ... 20
SELF-DIAGNOSTIC RESULTS ....................... ... 21
DATA MONITOR .............................................. ... 21
ACTIVE TEST .................................................. ... 23
Auto Active Test .................................................. ... 24
DESCRIPTION ................................................. ... 24
OPERATION PROCEDURE ............................ ... 24
INSPECTION IN AUTO ACTIVE TEST MODE ... 24
Schematic ........................................................... ... 26
IPDM E/R Terminal Arrangement ........................ ... 27
IPDM E/R Power/Ground Circuit Inspection ....... ... 28Inspection with CONSULT-II (Self-Diagnosis) .....
... 29
Removal and Installation of IPDM E/R ................ ... 30
REMOVAL ........................................................ ... 30
INSTALLATION ................................................ ... 30
GROUND CIRCUIT ................................................ ... 31
Ground Distribution ................................................. 31 MAIN HARNESS ................................................. 31
ENGINE ROOM HARNESS ............................. ... 34
ENGINE CONTROL HARNESS ....................... ... 37
BODY HARNESS ............................................. ... 38
BODY NO. 2 HARNESS .................................. ... 39
BACK DOOR NO. 2 RH HARNESS ................. ... 40
HARNESS .............................................................. ... 41
Harness Layout ...................................................... 41 HOW TO READ HARNESS LAYOUT .............. ... 41
OUTLINE .......................................................... ... 42
MAIN HARNESS ................................................. 43
ENGINE ROOM HARNESS (LH VIEW) ........... ... 45
ENGINE ROOM HARNESS (RH VIEW) .......... ... 48
ENGINE CONTROL HARNESS ....................... ... 50
CHASSIS HARNESS ....................................... ... 52
BODY HARNESS ............................................. ... 54
BODY NO. 2 HARNESS .................................. ... 56
ROOM LAMP HARNESS ................................. ... 58
FRONT DOOR LH HARNESS ......................... ... 59
FRONT DOOR RH HARNESS ......................... ... 59
REAR DOOR LH HARNESS ............................ ... 60
REAR DOOR RH HARNESS ........................... ... 60
BACK DOOR HARNESS ................................. ... 61
Wiring Diagram Codes (Cell Codes) ................... ... 62
ELECTRICAL UNITS LOCATION ......................... ... 65
Electrical Units Location ...................................... ... 65
ENGINE COMPARTMENT ............................... ... 65
PASSENGER COMPARTMENT ...................... ... 66
HARNESS CONNECTOR ...................................... ... 68
Description ........................................................... ... 68
HARNESS CONNECTOR (TAB-LOCKING
TYPE) ............................................................... ... 68
HARNESS CONNECTOR (SLIDE-LOCKING