power steering INFINITI QX56 2006 Factory User Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2006, Model line: QX56, Model: INFINITI QX56 2006Pages: 3383, PDF Size: 51.76 MB
Page 625 of 3383
AV-32
AUDIO
Revision: November 20092006 QX56
Trouble DiagnosisEKS00BIG
The majority of the audio troubles are the result of outside causes (bad CD, electromagnetic interference,
etc.). Check the inspection items below to diagnose the malfunction.
MALFUNCTION WITH RADIO AND CD
Before proceeding, confirm that other AV switch functions (except audio functions) operate. If not, refer to AV-
155, "Unable to Operate All of AV Switches (Unable to Start Self-Diagnosis)" .
FOR RADIO ONLY
SymptomPossible cause
Inoperative
Audio unit power circuit check. Refer to AV- 3 5 , "Power Supply Circuit
Inspection" .
Audio communication line check. Refer to AV-136, "Audio Communication
Line Check (Between Display Control Unit and Audio Unit)" .
AV switch check. Refer to AV- 4 3 , "AV Switch Check" .
If above check is OK, replace audio unit.
Steering switch does not operate
Steering switch check. Refer to AV-41, "Steering Switch Check" .
AV switch check. Refer to AV- 4 3 , "AV Switch Check" .
If above check is OK, replace audio unit.
Audio information is not displayed on screen
Display unit check. Refer to AV- 11 2 , "Self-Diagnosis Mode (DCU)" .
All speakers do not sound
Audio unit
BOSE speaker amp. power supply and ground circuit check. Refer to AV- 3 5 ,
"Power Supply Circuit Inspection" .
BOSE speaker amp. ON signal
BOSE speaker amp.
One or several speakers do not sound
Front door speaker check. Refer to AV-44, "Sound Is Not Heard From Front
Door Speaker or Front Tweeter" .
Rear door speaker check. Refer to AV- 4 8 , "Sound Is Not Heard From Rear
Door Speaker or Rear Door Tweeter" .
Subwoofer check. Refer to AV- 5 2 , "Sound Is Not Heard From Subwoofer" .
Center speaker check. Refer to AV- 5 1 , "Sound Is Not Heard From Center
Speaker" .
Poor sound
Audio unit
BOSE speaker amp.
Speaker
Noisy
Audio unit
BOSE speaker amp.
Electrical equipment (generator, bonding wire, etc.)
Symptom Possible cause
No sound
Audio unit
Antenna feeder, wiring or connections
Antenna amplifier, power supply, wiring or connections
Noisy
Audio unit
Audio unit case ground
Antenna feeder, wiring or connections
Antenna amplifier, power supply, wiring or connections
Noise prevention parts
Each electrical equipment
Wire harness of each piece of electrical equipment
All radio stations stored in memory are deleted
Audio unit power circuit check. Refer to AV-35, "Power Supply Cir-
cuit Inspection" .
Audio unit
Page 636 of 3383
AUDIOAV-43
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
4. SPIRAL CABLE CHECK
1. Disconnect spiral cable connector M102.
2. Check continuity between spiral cable terminals.
OK or NG
OK >> GO TO 5.
NG >> Replace spiral cable. Refer to SRS-48, "
SPIRAL CABLE" .
5. CHECK STEERING SWITCH RESISTANCE
Check resistance between steering switch terminals.
OK or NG
OK >> Inspection End.
NG >> Replace steering switch. Refer to AV- 5 9 , "
STEERING WHEEL AUDIO CONTROL SWITCHES" .
AV Switch CheckEKS00BIK
1. AV SWITCH SELF-DIAGNOSIS FUNCTION CHECK
1. Perform AV switch self-diagnosis function. Refer to AV- 3 1 , "
AV Switch Self-Diagnosis Function" .
Does AV switch operate normally?
YES >> Inspection End.
NO >> GO TO 2.
2. CHECK AV SWITCH POWER SUPPLY AND GROUND CIRCUIT
1. Check AV switch power supply and ground circuit. Refer to AV- 1 3 0 , "
Power Supply and Ground Circuit
Check for AV Switch" .
OK or NG
YES >> Replace AV switch. Refer to AV- 5 5 , "AV SWITCH" .
NO >> Repair malfunctioning part.
Terminals
Continuity
Spiral cable
Connector Terminal Connector Terminal
M30 32
M102 16
Ye s
31 17
24 20
WKIA4424E
Terminal Signal name ConditionResistance
(Ω )
(Approx.)
16 17 Seek (down) Depress (station) down switch. 165
Power
Depress power switch. 0
Volume (down) Depress volume down switch. 652
20 17 Seek (up) Depress (station) up switch.
165
Mode Depress mode switch. 0
Volume (up) Depress volume up switch. 652
WKIA4457E
Page 658 of 3383
TELEPHONEAV-65
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
System DescriptionEKS00GBL
BLUETOOTH® HANDS-FREE PHONE SYSTEM
Refer to the Owner's Manual for Bluetooth telephone system operating instructions.
NOTE:
Cellular telephones must have their wireless connection set up (paired) before using the Bluetooth telephone
system.
Bluetooth telephone system allows users who have a Bluetooth cellular telephone to make a wireless connec-
tion between their cellular telephone and the Bluetooth control unit. Hands-free cellular telephone calls can be
sent and received. Personal memos can be created using the Infinity Voice Recognition system. Some Blue-
tooth cellular telephones may not be recognized by the Bluetooth control unit. When a cellular telephone or
the Bluetooth control unit is replaced, the telephone must be paired with the Bluetooth control unit. Different
cellular telephones may have different pairing procedures. Refer to the cellular telephone operating manual.
Bluetooth Telephone System Diagram
Bluetooth Control Unit
When the ignition switch is turned to ACC or ON, the Bluetooth control unit will power up. During power up, the
Bluetooth control unit is initialized and performs various self checks. Initialization may take up to 10 seconds.
During this time the Bluetooth ON indicator will flash until initialization is complete. Infinity Voice Recognition
will then become active and the Bluetooth ON indicator will remain on. Bluetooth telephone functions can be
turned off using the voice recognition system.
BCM
The BCM supplies power for the Bluetooth ON indicator.
Steering Wheel Audio Control Switches
When buttons on the steering wheel audio control switch are pushed, the resistance in steering wheel audio
control switch circuit changes depending on which button is pushed. The Bluetooth control module uses this
signal to perform various functions while navigating through the voice recognition system.
The following functions can be performed using the steering wheel audio control switch:
Initiate Self Diagnosis of the Bluetooth telephone system
Start a voice recognition session
Answer and end telephone calls
Adjust the volume of calls
Record memos
AV S w i t c h
Call volume can be adjusted using the AV switch.
WKIA4569E
Page 662 of 3383
TELEPHONEAV-69
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
Terminals and Reference Value for Bluetooth Control UnitEKS00GBO
Terminal
(Wire color) ItemSignal
input/
output Condition
Reference value
(Approx.) Example of symptom
+ – Ignition
switch Operation
1 (Y) Ground Battery
powerInput
–– Battery voltageSystem does not
work properly.
2 (V) Ground ACC power Input ACC/
ON –
Battery voltage System does not
work properly.
3 (G/R) Ground IGN power Input ON/
START –
Battery voltage System does not
work properly.
4 (B) –Ground –– – ––
6 –Shield –– – ––
7 (B) 8 (R/L) Mic-in signal Input ON –– –
9 (R/W) 10 (R) Audio out Output ––––
11 ( B ) –Mute –– – ––
12 (R/G) Ground Remote
control A Input ON Press MODE
switch Approx. 0V
Steering wheel audio
controls do not func-
tion.
Press SEEK UP
switch Approx. 0.75V
Press VOL UP switch Approx. 2V
Except for above Approx. 5V
13 (G/W) Ground Remote
control B Input ON Press POWER
switch Approx. 0V
Steering wheel audio
controls do not func-
tion.
Press SEEK
DOWN switch Approx. 0.75V
Press VOL
DOWN switch Approx. 2V
Except for above Approx. 5V
14 (Y/R) - Remote
control
ground -- -
-Steering wheel audio
controls do not func-
tion.
15 (GR) - LED - - -- -
17 (V) Ground AV switch 1 Output On Press MODE
switch Approx. 0V
Steering wheel audio controls do not func- tion.
Press SEEK UP
switch Approx. 0.75V
Press VOL UP switch Approx. 2V
Except for above Approx 5V
18 (G/O) Ground AV switch 2 Output ON Press POWER
switch Approx. 0V
Steering wheel audio controls do not func- tion.
Press SEEK
DOWN switch Approx. 0.75V
Prees VOL
DOWN switch Approx. 2V
Except for above Approx 5V
19 (R/B) - AV switch
ground -- -
-Steering wheel audio
controls do not func- tion.
21 (B) - Ground - - -- –
Page 701 of 3383
AV-108
NAVIGATION SYSTEM
Revision: November 20092006 QX56
Terminals and Reference Value for AV SwitchEKS00BJN
Terminal No.
(Wire color) ItemSignal
input/
output Condition
Voltage
(Approx.) Example of
symptom
+ – Ignition
switch Operation
1 (Y) Ground Battery
power Input OFF
-Battery voltage System does not
work properly.
2 (V) Ground ACC signal Input ACC -Battery voltage System does not
work properly.
3 (R/L) Ground Illumination
signal Input OFF Lighting switch is
ON (position 1).
Battery voltageAV switch illumi-
nation does not
come on when
lighting switch is
ON (position 1).
Turn lighting switch
OFF.
3.0V or less
4 (BR) Ground Illumination
control signal Input ON Illumination control
switch is operated
by lighting switch in
1st position. Changes between 0 and 12V.
AV switch illumi-
nation cannot be
controlled.
5 (B) Ground Ground - ON -0V -
6 (V) Ground Communica-
tion signal (+) Input/
output ON
- System does not
work properly.
7- Shield
ground -- -
--
8 (LG) Ground Communica-
tion signal (-) Input/
output ON
- System does not
work properly.
12 (R) Ground Remote con-
trol A Input ON Press MODE
switch 0V
Steering wheel
audio controls
do not function.
Press SEEK UP
switch 0.75V
Press VOL UP switch 2V
Except for above 5V
13 (G) Ground Remote con-
trol B Input ON Press POWER
switch 0V
Steering wheel
audio controls
do not function.
Press SEEK
DOWN switch 0.75V
Press VOL DOWN switch 2V
Except for above 5V
14 (L) - Remote con-
trol ground -- -
-Steering wheel
audio controls
do not function.
SKIA0175E
SKIA0176E
Page 1028 of 3383
BRC-1
BRAKE CONTROL SYSTEM
F BRAKES
CONTENTS
C
DE
G H
I
J
K L
M
SECTION
A
B
BRC
Revision: November 2009 2006 QX56VDC/TCS/ABS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 3
Precautions for Brake System ............................. ..... 3
Precautions When Using CONSULT-II ................ ..... 3
CHECK POINTS FOR USING CONSULT-II .... ..... 3
Precautions for Brake Control ............................. ..... 4
Precautions for CAN System .............................. ..... 4
PREPARATION ...................................................... ..... 6
Special Service Tool ............................................ ..... 6
Commercial Service Tools ................................... ..... 6
SYSTEM DESCRIPTION ............................................ 7 System Components ........................................... ..... 7
ABS Function ........................................................... 8
EBD Function ...................................................... ..... 8
TCS Function ...................................................... ..... 8
VDC Function ...................................................... ..... 8
Fail-Safe Function .................................................... 8 ABS/EBD SYSTEM .......................................... ..... 9
VDC/TCS SYSTEM .......................................... ..... 9
ACTIVE BOOSTER .......................................... ..... 9
Hydraulic Circuit Diagram ................................... ..... 9
CAN COMMUNICATION ....................................... ... 10
System Description ............................................. ... 10
TROUBLE DIAGNOSIS ......................................... ....11
How to Perform Trouble Diagnoses for Quick and
Accurate Repair .................................................. .... 11
INTRODUCTION .............................................. .... 11
WORK FLOW ................................................... ... 12
CLARIFY CONCERN ....................................... ... 13
EXAMPLE OF DIAGNOSIS SHEET ................ ... 13
Component Parts and Harness Connector Location ... 14
Schematic ........................................................... ... 15
Wiring Diagram — VDC — .................................. ... 16
Basic Inspection .................................................. ... 23
BRAKE FLUID LEVEL, FLUID LEAK, AND
BRAKE PAD INSPECTION .............................. ... 23
POWER SYSTEM TERMINAL LOOSENESS AND BATTERY INSPECTION ..........................
... 23
ABS WARNING LAMP, SLIP INDICATOR LAMP
AND VDC OFF INDICATOR LAMP INSPECTION ... 23
Warning Lamp and Indicator Timing .................... ... 24
Control Unit Input/Output Signal Standard .......... ... 24
REFERENCE VALUE FROM CONSULT-II ...... ... 24
CONSULT-II Function (ABS) ............................... ... 28
CONSULT-II BASIC OPERATION PROCEDURE ... 28
SELF-DIAGNOSIS ........................................... ... 29
DATA MONITOR .............................................. ... 32
ACTIVE TEST ..................................................... 35
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ..................................................................... ... 38
Wheel Sensor System Inspection ........................ ... 38
Engine System Inspection ................................... ... 39
ABS/TCS/VDC Control Unit Inspection ............... ... 40
Steering Angle Sensor System ............................ ... 40
Yaw Rate/Side/Decel G Sensor System Inspection ... 41
Solenoid and VDC Change-Over Valve System
Inspection ............................................................ ... 43
Actuator Motor, Motor Relay, and Circuit Inspection ... 44
Stop Lamp Switch System Inspection ................. ... 45
ABS/TCS/VDC Control Unit Power and Ground
Systems Inspection ............................................. ... 46
Brake Fluid Level Switch System Inspection ....... ... 47
Active Booster System Inspection ....................... ... 48
Delta Stroke Sensor System Inspection .............. ... 49
Pressure Sensor System Inspection ................... ... 51
Steering Angle Sensor Safe Mode Inspection ..... ... 53
CAN Communication System Inspection ............. ... 54
ICC System Inspection ........................................ ... 54
Inspection For Self-diagnosis Result "ST ANG SEN
SIGNAL" .............................................................. ... 55
Inspection For Self-diagnosis Result "DECEL G
SEN SET" ............................................................ ... 55
VDC OFF Indicator lamp Does Not Illuminate ..... ... 56
Component Inspection ......................................... ... 56
VDC OFF SWITCH .......................................... ... 56
Page 1052 of 3383
![INFINITI QX56 2006 Factory User Guide TROUBLE DIAGNOSISBRC-25
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
STR ANGLE SIGSteering angle
detected by steering
angle sensorStraight-ahead
Approx. 0 deg
BRC-40, "](/img/42/57028/w960_57028-1051.png "INFINITI QX56 2006 Factory User Guide TROUBLE DIAGNOSISBRC-25
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
STR ANGLE SIGSteering angle
detected by steering
angle sensorStraight-ahead
Approx. 0 deg
BRC-40, \"")
TROUBLE DIAGNOSISBRC-25
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
STR ANGLE SIGSteering angle
detected by steering
angle sensorStraight-ahead
Approx. 0 deg
BRC-40, "Steering Angle
Sensor System"Steering wheel turned –756 to 756 deg
YAW RATE SEN Yaw rate detected by
yaw rate sensorVehicle stopped Approx. 0 d/s
BRC-41, "
Yaw Rate/Side/
Decel G Sensor System
Inspection"Vehicle running–100 to 100 d/s
SIDE G-SENSOR Transverse G detected
by side G-sensorVehicle stopped
Approx. 0 m/s
2BRC-41, "Yaw Rate/Side/
Decel G Sensor System
Inspection"Vehicle running–16.7 to 16.7 m/s2
BATTERY VOLT Battery voltage sup-
plied to ABS actuator
and electric unit (con-
trol unit)Ignition switch ON
10 to 16VBRC-46, "
ABS/TCS/VDC
Control Unit Power and
Ground Systems Inspec-
tion"
STOP LAMP SW
Stop lamp switch oper-
ationBrake pedal depressed ON
BRC-45, "
Stop Lamp
Switch System Inspec-
tion"Brake pedal not depressed OFF
OFF SW VDC OFF switch
ON/OFF status VDC OFF switch ON
(When VDC OFF indicator
lamp is ON)
ON
BRC-56, "
VDC OFF
SWITCH"VDC OFF switch OFF
(When VDC OFF indicator
lamp is OFF) OFF
ABS WARN LAMP ABS warning lamp ON
condition (Note 2)ABS warning lamp ON ON
—
ABS warning lamp OFF OFF
MOTOR RELAY Operation status of
motor and motor relayIgnition switch ON or running
(ABS not activated)
OFF
BRC-44, "
Actuator Motor,
Motor Relay, and Circuit
Inspection"Ignition switch ON or engine
running (ABS activated) ON
ACTUATOR RLY Actuator relay opera-
tion statusVehicle stopped (Ignition
switch ON)
OFF
BRC-44, "
Actuator Motor,
Motor Relay, and Circuit
Inspection"Vehicle stopped (Engine run-
ning) ON
OFF LAMP VDC OFF indicator
lamp status (Note 3) When VDC OFF indicator
lamp is ON
ON
BRC-54, "
CAN Commu-
nication System Inspec-
tion"When VDC OFF indicator
lamp is OFF OFF
SLIP LAMP SLIP indicator lamp
status (Note 4)When SLIP indicator lamp is
ON
ON
BRC-54, "
CAN Commu-
nication System Inspec-
tion"When SLIP indicator lamp is
OFF OFF
Monitor item
Display content Data monitor
Note: Error inspection
checklist
Condition Reference value in
normal operation
Page 1057 of 3383
![INFINITI QX56 2006 Factory User Guide BRC-30
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Display Item List
Self-diagnostic itemMalfunction detecting condition Check system
FR LH SENSOR 1
[C1104] Circuit of front LH wh](/img/42/57028/w960_57028-1056.png "INFINITI QX56 2006 Factory User Guide BRC-30
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Display Item List
Self-diagnostic itemMalfunction detecting condition Check system
FR LH SENSOR 1
[C1104] Circuit of front LH wh")
BRC-30
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Display Item List
Self-diagnostic itemMalfunction detecting condition Check system
FR LH SENSOR 1
[C1104] Circuit of front LH wheel sensor is open, shorted or sensor power
voltage is unusual.
BRC-38, "
Wheel Sensor
System Inspection"
(Note 1)
RR RH SENSOR 1
[C1101]
Circuit of rear RH wheel sensor is open, shorted or sensor power
voltage is unusual.
FR RH SENSOR 1
[C1103] Circuit of front RH wheel sensor is open, shorted or sensor power
voltage is unusual.
RR LH SENSOR 1
[C1102] Circuit of rear LH wheel sensor is open, shorted or sensor power
voltage is unusual.
FR LH SENSOR 2
[C1108] ABS actuator and electric unit (control unit) cannot identify sen-
sor pulses, because of large gap between wheel sensor and sen-
sor rotor.
RR RH SENSOR 2
[C1105] ABS actuator and electric unit (control unit) cannot identify sen-
sor pulses, because of large gap between wheel sensor and sen-
sor rotor.
FR RH SENSOR 2
[C1107] ABS actuator and electric unit (control unit) cannot identify sen-
sor pulses, because of large gap between wheel sensor and sen-
sor rotor.
RR LH SENSOR 2
[C1106] ABS actuator and electric unit (control unit) cannot identify sen-
sor pulses, because of large gap between wheel sensor and sen-
sor rotor.
ABS SENSOR
[C1115] Wheel sensor input is abnormal.
STOP LAMP SW
[C1116] Stop lamp switch or circuit malfunction. BRC-45, "
Stop Lamp
Switch System Inspec-
tion"
DECEL G SEN SET
[C1160]
ABS decel sensor adjustment is incomplete. BRC-55, "Inspection For
Self-diagnosis Result
"DECEL G SEN SET""
ST ANGL SEN SAFE
[C1163]
When steering angle sensor is in safe mode. BRC-53, "Steering Angle
Sensor Safe Mode
Inspection"
ST ANG SEN CIRCUIT
[C1143]
Neutral position of steering angle sensor is dislocated, or steer-
ing angle sensor is malfunctioning. BRC-40, "Steering Angle
Sensor System"
YAW RATE SENSOR
[C1145]Yaw rate sensor has generated an error, or yaw rate sensor sig-
nal line is open or shorted. BRC-41, "Yaw Rate/
Side/Decel G Sensor
System Inspection"
Page 1058 of 3383
![INFINITI QX56 2006 Factory User Guide TROUBLE DIAGNOSISBRC-31
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
FR LH IN ABS SOL
[C1120]Circuit of front LH IN ABS solenoid is open or shorted, or control
line is o](/img/42/57028/w960_57028-1057.png "INFINITI QX56 2006 Factory User Guide TROUBLE DIAGNOSISBRC-31
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
FR LH IN ABS SOL
[C1120]Circuit of front LH IN ABS solenoid is open or shorted, or control
line is o")
TROUBLE DIAGNOSISBRC-31
[VDC/TCS/ABS]
C
DE
G H
I
J
K L
M A
B
BRC
Revision: November 2009 2006 QX56
FR LH IN ABS SOL
[C1120]Circuit of front LH IN ABS solenoid is open or shorted, or control
line is open or shorted to power supply or ground.
BRC-43, "
Solenoid and
VDC Change-Over Valve
System Inspection"
FR LH OUT ABS SOL
[C1121]Circuit of front LH OUT ABS solenoid is open or shorted, or con-
trol line is open or shorted to power supply or ground.
RR RH IN ABS SOL
[C1126] Circuit of rear RH IN ABS solenoid is open or shorted, or control
line is open or shorted to power supply or ground.
RR RH OUT ABS SOL
[C1127] Circuit of rear RH OUT ABS solenoid is open or shorted, or con-
trol line is open or shorted to power supply or ground.
FR RH IN ABS SOL
[C1122] Circuit of front RH IN ABS solenoid is open or shorted, or control
line is open or shorted to power supply or ground.
FR RH OUT ABS SOL
[C1123] Circuit of front RH OUT ABS solenoid is open or shorted, or con-
trol line is open or shorted to power supply or ground.
RR LH IN ABS SOL
[C1124] Circuit of rear LH IN ABS solenoid is open or shorted, or control
line is open or shorted to power supply or ground.
RR LH OUT ABS SOL
[C1125] Circuit of rear LH OUT ABS solenoid is open or shorted, or con-
trol line is open or shorted to power supply or ground.
CV1
[C1164] Front side VDC switch-over solenoid valve (cut valve) is open or
shorted, or control line is open or shorted to power supply or
ground.
CV2
[C1165] Rear side VDC switch-over solenoid valve (cut valve) is open or
shorted, or control line is open or shorted to power supply or
ground.
SV1
[C1166] Front side VDC switch-over solenoid valve (suction valve) is
open or shorted, or control line is open or shorted to power sup-
ply or ground.
SV2
[C1167] Rear side VDC switch-over solenoid valve (suction valve) is open
or shorted, or control line is open or shorted to power supply or
ground.
PUMP MOTOR
[ C 1111 ] During actuator motor operation with ON, when actuator motor
turns OFF or when control line for actuator motor relay is open.
BRC-44, "
Actuator
Motor, Motor Relay, and
Circuit Inspection"During actuator motor operation with OFF, when actuator motor
turns ON or when control line for relay is shorted to ground.
BATTERY VOLTAGE
[ABNORMAL]
[C1109] ABS actuator and electric unit (control unit) power voltage is too
low. BRC-46, "
ABS/TCS/
VDC Control Unit Power
and Ground Systems
Inspection"
ST ANG SEN SIGNAL
[C1144]
Neutral position correction of steering angle sensor is not fin-
ished. BRC-55, "Inspection For
Self-diagnosis Result
"ST ANG SEN SIGNAL""
ST ANG SEN COM CIR
[C1156]
CAN communication line or steering angle sensor has generated
an error. BRC-40, "Steering Angle
Sensor System"
G-SENSOR
[C1113]Longitudinal G-sensor is malfunctioning, or signal line of longitu-
dinal G-sensor is open or shorted. BRC-41, "Yaw Rate/
Side/Decel G Sensor
System Inspection"
CONTROLLER FAILURE
[C1110]
Internal malfunction of ABS actuator and electric unit (control
unit) BRC-40, "ABS/TCS/
VDC Control Unit
Inspection"
CAN COMM CIRCUIT
[U1000]
CAN communication line is open or shorted.
ABS actuator and electric unit (control unit) internal malfunc-
tion
Battery voltage for ECM is suddenly interrupted for approxi-
mately 0.5 second or more.BRC-54, "
CAN Commu-
nication System Inspec-
tion" (Note 2)
SIDE G-SEN CIRCUIT
[C1146] Lateral G-sensor is malfunctioning, or signal line of lateral G-sen-
sor is open or shorted. BRC-41, "
Yaw Rate/
Side/Decel G Sensor
System Inspection"
Self-diagnostic item
Malfunction detecting condition Check system
Page 1216 of 3383
EC-5
C
DE
F
G H
I
J
K L
M
EC A
Revision: November 2009 2006 QX56
Component Description .......................................
. 440
On Board Diagnosis Logic .................................. . 440
DTC Confirmation Procedure .............................. . 440
Diagnostic Procedure .......................................... . 441
Removal and Installation ..................................... . 441
DTC P0500 VSS .................................................... . 442
Description .......................................................... . 442
On Board Diagnosis Logic .................................. . 442
DTC Confirmation Procedure .............................. . 442
Overall Function Check ....................................... . 442
Diagnostic Procedure .......................................... . 443
DTC P0506 ISC SYSTEM ...................................... . 444
Description .......................................................... . 444
On Board Diagnosis Logic .................................. . 444
DTC Confirmation Procedure .............................. . 444
Diagnostic Procedure .......................................... . 445
DTC P0507 ISC SYSTEM ...................................... . 446
Description .......................................................... . 446
On Board Diagnosis Logic .................................. . 446
DTC Confirmation Procedure .............................. . 446
Diagnostic Procedure .......................................... . 447
DTC P0550 PSP SENSOR .................................... . 448
Component Description ....................................... . 448
CONSULT-II Reference Value in Data Monitor Mode . 448
On Board Diagnosis Logic .................................. . 448
DTC Confirmation Procedure .............................. . 448
Wiring Diagram ................................................... . 449
Diagnostic Procedure .......................................... . 450
Component Inspection ........................................ . 452
Removal and Installation ..................................... . 452
DTC P0603 ECM POWER SUPPLY ...................... . 453
Component Description ....................................... . 453
On Board Diagnosis Logic .................................. . 453
DTC Confirmation Procedure .............................. . 453
Wiring Diagram ................................................... . 454
Diagnostic Procedure .......................................... . 455
DTC P0605 ECM ................................................... . 457
Component Description ....................................... . 457
On Board Diagnosis Logic .................................. . 457
DTC Confirmation Procedure .............................. . 457
Diagnostic Procedure .......................................... . 458
DTC P0643 SENSOR POWER SUPPLY ............... . 460
On Board Diagnosis Logic .................................. . 460
DTC Confirmation Procedure .............................. . 460
Wiring Diagram ................................................... . 461
Diagnostic Procedure .......................................... . 463
DTC P0850 PNP SWITCH ..................................... . 465
Component Description ....................................... . 465
CONSULT-II Reference Value in Data Monitor Mode . 465
On Board Diagnosis Logic .................................. . 465
DTC Confirmation Procedure .............................. . 465
Overall Function Check ....................................... . 466
Wiring Diagram ................................................... . 467
Diagnostic Procedure .......................................... . 468
DTC P1148, P1168 CLOSED LOOP CONTROL ... . 470
On Board Diagnosis Logic .................................. . 470
DTC P1211 TCS CONTROL UNIT ........................ . 471Description ...........................................................
.471
On Board Diagnosis Logic ................................... .471
DTC Confirmation Procedure .............................. .471
Diagnostic Procedure .......................................... .471
DTC P1212 TCS COMMUNICATION LINE ........... .472
Description ........................................................... .472
On Board Diagnosis Logic ................................... .472
DTC Confirmation Procedure .............................. .472
Diagnostic Procedure .......................................... .472
DTC P1217 ENGINE OVER TEMPERATURE ....... .473
Description ........................................................... .473
CONSULT-II Reference Value in Data Monitor Mode .473
On Board Diagnosis Logic ................................... .474
Overall Function Check ....................................... .474
Wiring Diagram .................................................... .476
Diagnostic Procedure .......................................... .478
Main 12 Causes of Overheating .......................... .481
Component Inspection ......................................... .482
DTC P1225 TP SENSOR ....................................... .483
Component Description ....................................... .483
On Board Diagnosis Logic ................................... .483
DTC Confirmation Procedure .............................. .483
Diagnostic Procedure .......................................... .484
Removal and Installation ..................................... .484
DTC P1226 TP SENSOR ....................................... .485
Component Description ....................................... .485
On Board Diagnosis Logic ................................... .485
DTC Confirmation Procedure .............................. .485
Diagnostic Procedure .......................................... .486
Removal and Installation ..................................... .486
DTC P1564 ICC STEERING SWITCH ................... .487
Component Description ....................................... .487
CONSULT-II Reference Value in Data Monitor Mode .487
On Board Diagnosis Logic ................................... .487
DTC Confirmation Procedure .............................. .488
Wiring Diagram .................................................... .489
Diagnostic Procedure .......................................... .490
Component Inspection ......................................... .493
DTC P1564 ASCD STEERING SWITCH ............... .494
Component Description ....................................... .494
CONSULT-II Reference Value in Data Monitor Mode .494
On Board Diagnosis Logic ................................... .494
DTC Confirmation Procedure .............................. .495
Wiring Diagram .................................................... .496
Diagnostic Procedure .......................................... .497
Component Inspection ......................................... .500
DTC P1568 ICC FUNCTION .................................. .501
On Board Diagnosis Logic ................................... .501
DTC Confirmation Procedure .............................. .501
Diagnostic Procedure .......................................... .501
DTC P1572 ICC BRAKE SWITCH ......................... .502
Component Description ....................................... .502
CONSULT-II Reference Value in Data Monitor Mode .502
On Board Diagnosis Logic ................................... .502
DTC Confirmation Procedure .............................. .503