ignition INFINITI QX56 2006 Factory Service Manual

AV-148
NAVIGATION SYSTEM
Revision: November 20092006 QX56
2. CHECK RGB SIGNAL
1. Connect display control unit connector and display unit connec- tor.
2. Turn ignition switch ON.
3. Display “Color bar” by “CONFIRMATION/ADJUSTMENT ” mode.
4. Check the following with CONSULT-ll or oscilloscope.

When the screen looks reddish.
Voltage signal between display control unit connector M95 ter-
minal 52 and 47.
OK or NG
OK >> Replace display unit. Refer to AV- 1 6 7 , "DISPLAY UNIT" .
NG >> Replace display control unit. Refer to AV- 1 6 7 , "
DISPLAY CONTROL UNIT" .
Color of RGB Image is Not Proper (All Screens Look Yellowish)EKS00GEU
1. CHECK RGB HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95 and display unit connector M93.
3. Check continuity between display control unit and display unit.
4. Check continuity between display control unit and ground.

When the screen looks yellowish.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector. 52 - 47
: Refer to AV- 1 0 2 , "
Terminals
and Reference Value for Dis-
play Control unit" .
SKIA4698E
Terminals
Continuity
Display control unit Display unit
Connector Terminal Connector Terminal
M95 54
M93 18
Ye s
47 7
Terminals Continuity
Display control unit
—
Connector Terminal
M95 54
GroundNo
47
SKIA4355E

NAVIGATION SYSTEMAV-149
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
2. CHECK RGB SIGNAL
1. Connect display control unit connector and display unit connec- tor.
2. Turn ignition switch ON.
3. Display “Color bar” by “CONFIRMATION/ADJUSTMENT ” mode.
4. Check the following with CONSULT-ll or oscilloscope.

When the screen looks yellowish.
Voltage signal between display control unit connector M95 ter-
minal 54 and 47.
OK or NG
OK >> Replace display unit. Refer to AV- 1 6 7 , "DISPLAY UNIT" .
NG >> Replace display control unit. Refer to AV- 1 6 7 , "
DISPLAY CONTROL UNIT" .
54 - 47 : Refer to
AV- 1 0 2 , "
Te r m i n a l s
and Reference Value for Dis-
play Control unit" .
SKIA4356E

AV-150
NAVIGATION SYSTEM
Revision: November 20092006 QX56
NAVI Screen is RollingEKS00GEV
1. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152 and display control unit connector M95.
3. Check continuity between NAVI control unit and display control unit.
4. Check continuity between NAVI control unit and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness.
2. CHECK RGB SYNCHRONIZING SIGNAL
1. Connect NAVI control unit connector and display control unit connector.
2. Turn ignition switch ON.
3. Check signal between NAVI control unit connector M95 termi- nals 48 and 49 with CONSULT-ll or oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> Replace NAVI control unit. Refer to AV- 1 6 8 , "
NAVI CONTROL UNIT" .
Terminals
Continuity
BA
Connector Terminal Connector Terminal
NAVI control unit: B152 48 Display con-
trol unit:M95 43
Ye s
49 41
Terminals Continuity
B
—
Connector Terminal
NAVI control unit: B152 48
GroundNo
49
WKIA4224E
48 - 49 : Refer to AV- 1 0 0 , "Terminals
and Reference Value for
NAVI Control Unit" .
WKIA4225E

NAVIGATION SYSTEMAV-151
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
3. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95 and display unit connector M93.
3. Check continuity between display control unit and display unit.
4. Check continuity between display control unit and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness.
4. CHECK RGB SYNCHRONIZING SIGNAL
1. Connect display control unit connector and display unit connec- tor.
2. Turn ignition switch ON.
3. Check signal between display unit connector M93 terminals 19 and 21 with CONSULT-ll or oscilloscope.
OK or NG
OK >> Replace display unit. Refer to AV- 1 6 7 , "DISPLAY UNIT"
.
NG >> Replace display control unit. Refer to .
Terminals
Continuity
Display control unit Display unit
Connector Terminal Connector Terminal
M95 56
M93 19
Ye s
49 21
Terminals Continuity
Display control unit
—
Connector Terminal
M95 56
Ground No
49
WKIA2775E
19 - 21 : Refer to AV- 1 0 2 , "Te r m i n a l s
and Reference Value for Dis-
play Control unit" .
WKIA2022E

AV-152
NAVIGATION SYSTEM
Revision: November 20092006 QX56
Guide Sound is Not HeardEKS00GEW
1. CHECK VOICE GUIDE SETTING
While driving in the dark pink route, voice guide does not operate. (note)
NOTE:
Voice guide is only available at intersections that satisfy certain conditions (indicated by

on the map). There-
fore, guidance may not be given even when the route on the map changes direction.
Is volume setting switched OFF?
YES >> Switch the setting ON and turn the volume up.
NO >> GO TO 2.
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B151 and audio unit connector M45.
3. Check continuity between NAVI control unit and audio unit.
4. Check continuity between NAVI control unit and ground.
Ok or NG
OK >> GO TO 3.
NG >> Repair harness.
3. CHECK VOICE GUIDE
1. Connect NAVI control unit connector and audio unit connector.
2. Turn ignition switch ON.
3. Check signal between NAVI control unit harness connector B151 terminal 12 and 14 with CONSULT-ll or oscilloscope.
OK or NG
OK >> Replace audio unit. Refer to AV- 5 5 , "AUDIO UNIT" .
NG >> Replace NAVI control unit. Refer to AV- 1 6 8 , "
NAVI CON-
TROL UNIT" .
Terminals
Continuity
BA
Connector Terminal Connector Terminal
NAVI control unit: B151 12
Audio unit:
M45 71
Ye s
14 69
Terminals Continuity
B
—
Connector Terminal (Wire color)
NAVI control unit: B151 12
GroundNo
14
WKIA4226E
12 - 14 : Refer to AV- 1 0 0 , "Terminals
and Reference Value for
NAVI Control Unit" .
WKIA4227E

NAVIGATION SYSTEMAV-153
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
Screen is Not ShownEKS00GEX
1. POWER SUPPLY AND GROUND CIRCUIT CHECK
Check power supply and ground circuit for display unit. Refer to AV- 1 2 8 , "
Power Supply and Ground Circuit
Check for Display Unit" .
OK or NG
OK >> Replace display unit. Refer to AV- 1 6 7 , "DISPLAY UNIT" .
NG >> Check the malfunctioning parts.
A/C Screen is Not Shown (NAVI Screen is Shown)EKS00GEY
1. CHECK IGNITION SIGNAL
Check ignition signal. Refer to AV- 1 3 4 , "
Ignition Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 4 0 , "
CAN Communication Line Check" .
OK or NG
OK >> Replace display control unit. Refer to AV- 1 6 7 , "DISPLAY CONTROL UNIT" .
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-26, "
CAN COMMUNI-
CATION" .
FUEL ECONOMY Screen is Not ShownEKS00GEZ
1. CHECK IGNITION SIGNAL
Check ignition signal. Refer to AV- 1 3 3 , "
Illumination Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 4 0 , "
CAN Communication Line Check" .
OK or NG
OK >> Replace display control unit. Refer to AV- 1 6 7 , "DISPLAY CONTROL UNIT" .
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-26, "
CAN COMMUNI-
CATION" .
Average Fuel Economy Displayed is Not Shown (“ *** ” is Shown)EKS00GF0
1. CHECK VEHICLE SPEED SIGNAL
Check vehicle speed signal. Refer to AV- 1 3 2 , "
Vehicle Speed Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 4 0 , "
CAN Communication Line Check" .
OK or NG
OK >> Replace display control unit. Refer to AV- 1 6 7 , "DISPLAY CONTROL UNIT" .
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-26, "
CAN COMMUNI-
CATION" .

AV-154
NAVIGATION SYSTEM
Revision: November 20092006 QX56
Distance to Empty Displayed is Not Shown (“ *** ” is Shown)EKS00GF1
1. CHECK SPEEDOMETER
Confirm that speedometer is functioning.
Is speedometer functioning?
YES >> GO TO 2.
NO >> Refer to DI-19, "
Vehicle Speed Signal Inspection" .
2. CHECK FUEL GAUGE
Confirm that fuel gauge is functioning.
Is fuel gauge functioning?
YES >> GO TO 3.
NO >> Refer to DI-22, "
Fuel Level Sensor Unit Inspection" .
3. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 4 0 , "
CAN Communication Line Check" .
OK or NG
OK >> Replace display control unit. Refer to AV- 1 6 7 , "DISPLAY CONTROL UNIT" .
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-26, "
CAN COMMUNI-
CATION" .
Driving Distance or Average Speed Displayed is Not Shown (“ *** ” is Shown)EKS00GF2
1. CHECK IGNITION SIGNAL
Check ignition signal. Refer to AV- 1 3 4 , "
Ignition Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-26, "
CAN COMMUNI-
CATION" .
2. CHECK VEHICLE SPEED SIGNAL
Check vehicle speed signal. Refer to AV- 1 3 2 , "
Vehicle Speed Signal Check for Display Control Unit" .
OK or NG
OK >> Replace display control unit. Refer to AV- 1 6 7 , "DISPLAY CONTROL UNIT" .
NG >> Check the malfunctioning parts.
WARNING DOOR OPEN Screen is Not ShownEKS00GF3
1. CHECK IGNITION SIGNAL
Check ignition signal. Refer to AV- 1 3 4 , "
Ignition Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK VEHICLE SPEED SIGNAL
Check vehicle speed signal. Refer to AV- 1 3 2 , "
Vehicle Speed Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 3.
NG >> Check the malfunctioning parts.

NAVIGATION SYSTEMAV-157
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
Driving TestEKS00GFB
1. DRIVING TEST 1
1. Scroll the map screen to display the area to make correction. Press “ENTER” and select “CURRENT
LOCATION CORRECTION ”.
2. Correct direction of the vehicle mark.
3. Perform the distance correction of the "CONFIRMATION/ADJUSTMENT" mode. Note: Normally, adjustment is not necessary because this system has automatic distance correction func-
tion. However, when a tire chain is fitted, adjustment in accordance with the tire diameter ratio must be
made.
4. Are symptoms malfunctioning to the AV- 1 5 8 , "
Example of Symptoms Judged Not Malfunction" after driv-
ing the vehicle?
YES or NO
YES >> Limit of the location detection capacity of the navigation system.
NO >> GO TO 2.
2. DRIVING TEST 2

Did any malfunction occur when the proper test in the following test patterns is performed?

Test pattern
Driving test finds the difference between the symptoms monitored with and without each sensor.
–Test pattern 1: Test method with no GPS location correction
Disconnect GPS antenna connector connected to the NAVI control unit. Accurately adjust the current
location and the direction, then drive the vehicle.
–Test pattern 2: Test method with no map-matching
Accurately adjust the current location and the direction. Eject the map DVD-ROM from the NAVI control
unit with ignition switch turned to OFF, then drive the vehicle. After driving, insert the map DVD-ROM back
in the unit, display the track of the vehicle on the map screen and compare it with the actual road configu-
ration.

Sample tests
– matching or by GPS>
Perform test pattern 1.
–
Perform test pattern 1 & 2.
Compare the track of the vehicle on the map screen and the actual road configuration. For fairly accurate
tracking, plotting shall be made every several hundred meters (feet).
–
Perform test pattern 1 & 2.
Drive on a road of which distance is accurately known (by utilizing distance posts on a highway). Calculate
the rate of change (increased/decreased) of the distance by comparing with the actual distance.
Correction = A/B
A: Distance shown on the screen
B: Actual distance
YES or NO
YES >>
If adjustment is insufficient, perform adjustment again.

If any error is found in the map, please contact map data supplier. Refer to Navigation System
Owner's Manual for contact information.

Replace NAVI control unit. Refer to AV- 1 6 8 , "NAVI CONTROL UNIT" .
NO >> Limit of the location detection capacity of the navigation system.

AV-158
NAVIGATION SYSTEM
Revision: November 20092006 QX56
Example of Symptoms Judged Not MalfunctionEKS00GFC
BASIC OPERATION
VEHICLE MARK
SymptomCause Remedy
No image is shown. Display brightness adjustment is set fully to
DARK side. Adjust the display brightness.
No guide sound is heard.
Audio guide volume is too low or
too high. Volume control is set to OFF, MIN or MAX. Adjust the audio guide volume.
Audio guidance is not available while the vehicle
is driving on a dark pink route.
System is not malfunctioning.
Screen is too dark.
Motion of the image is too slow. Temperature inside the vehicle is low.
Wait until the temperature inside the vehicle
reaches the proper temperature.
Small black or bright spots appear
on the screen. Symptom peculiar to a liquid crystal display (dis-
play unit). System is not malfunction.
Symptom
Cause Remedy
Map screen and BIRDVIEW ™
Name of the place varies with the
screen. Some thinning of the character data is done to
prevent the display becoming to complex. In
some cases and in some locations, the display
contents may differ.
The same place name, street name, etc. may not
be displayed every time on account of the data
processing. System is not malfunctioning.
Vehicle mark is not positioned cor-
rectly. Vehicle is transferred by ferry or by towing after its
ignition switch is turned to OFF. Drive the vehicle for a while in the GPS sat-
ellite signal receiving condition.
Screen will not switch to nighttime
mode after the lighting switch is
turned ON. The daytime screen is selected by the
“SWITCH
SCREENS ” when the last time the screen dim-
ming setting is done.
Switching between daytime/nighttime screen may
be inhibited by the automatic illumination adjust-
ment function. Perform screen dimming and select the
nighttime screen by
“SWITCH SCREENS ”.
Map screen will not scroll in accor-
dance with the vehicle travel. Current location is not displayed.
Press “MAP ” button to display the current
location.
Vehicle mark will not be shown. Current location is not displayed. Press “MAP ” button to display the current
location.
Accuracy indicator (GPS satellite
mark) on the map screen stays
gray. GPS satellite signal is intercepted because the
vehicle is in or behind a building.
Move the vehicle out to an open space.
GPS satellite signal cannot be received because
an obstacle is placed on top of the instrument
panel. Do not place anything in the center on top of
the display.
GPS satellites are not visible from current loca-
tion. Wait until GPS satellites are visible by mov-
ing the vehicle.
Vehicle location accuracy is low. Accuracy indicator (GPS satellite mark) on the map screen stays gray. Current location is not determined.
Vehicle speed setting by the vehicle speed pulse
has been deviated (advanced or retarded) from
the actual vehicle speed because tire chain is fit-
ted or the system has been used on another vehi-
cle. Drive the vehicle for a while [for approx. 30
minutes at approx. 30 km/h (19 MPH)] and
the deviation will be automatically adjusted.
If advancement or retard still occur, perform
the distance adjustment by CONFIRMA-
TION/ADJUSTMENT mode of diagnosis
function.
Map data has error or omission. (Vehicle mark is
always deviated to the same position.) As a rule, an updated map DVD
–ROM will
be released once a year.

NAVIGATION SYSTEMAV-163
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
PlaceIn a parking lot
When driving in a parking lot, or other loca-
tion where there are no roads on the map,
matching may place the vehicle mark on a
nearby road. When the vehicle returns to
the road, the vehicle mark may have devi-
ated from the correct location.
When driving in circle or turning the steer-
ing wheel repeatedly, direction errors accu-
mulate, and the vehicle mark may deviate
from the correct location.
If after travelling about 10 km (6
miles) the correct location has
not been restored, perform
location correction and, if nec-
essary, direction correction.
Turntable
When the ignition switch is OFF, the navi-
gation system cannot get the signal from
the gyroscope (angular speed sensor).
Therefore, the displayed direction may be
wrong and the correct road may not be
easily returned to after rotating the vehicle
on a turntable with the ignition OFF.
Slippery roads On snow, wet roads, gravel, or other roads
where tires may slip easily, accumulated
mileage errors may cause the vehicle mark
to deviate from the correct road.
Slopes When parking in sloped garages, when
travelling on banked roads, or in other
cases where the vehicle turns when tilted,
an error in the turning angle will occur, and
the vehicle mark may deviate from the
road.
Map data Road not displayed on the map screen
When driving on new roads or other roads
not displayed on the map screen, map
matching does not function correctly and
matches the location to a nearby road.
When the vehicle returns to a road which is
on the map, the vehicle mark may deviate
from the correct road.
Different road pattern
(Changed due to repair) If the road pattern stored in the map data
and the actual road pattern are different,
map matching does not function correctly
and matches the location to a nearby road.
The vehicle mark may deviate from the
correct road.
Vehicle Use of tire chains When tire chains are used, the mileage is
not correctly detected, and the vehicle
mark may deviate from the correct road.Drive the vehicle for a while. If
the distance still deviates,
adjust it by using the distance
adjustment function. (If the tire
chain is removed, recover the
original value.)
Cause (condition)
–: While driving ooo: Display Driving conditionRemarks (correction, etc.)
SEL709V
SEL710V
SEL699V
ELK0201D