bolt pattern INFINITI QX56 2006 Factory Service Manual

ON-VEHICLE SERVICEAT-229
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
2. Install the oil pan and new oil pan gasket.
CAUTION:

Do not reuse the oil pan gasket.

Completely remove all moisture, oil and old gasket from
the oil pan gasket mating surfaces and holes.

Always replace the oil pan bolts as they are self-sealing.

Be sure the oil pan drain plug hole is located to the rear
of the transmission assembly.

Partially install the oil pan bolts in a criss-cross pattern to
prevent dislocation of the gasket.

Be careful not to pinch harnesses.
3. Tighten new oil pan bolts in numerical order as shown.
4. Install drain plug in oil pan with new gasket. CAUTION:
Do not reuse the drain plug gasket.
5. Refill the transmission assembly with fluid. Refer to AT- 1 2 , "
Changing Automatic Transmission Fluid
(ATF)" .
SCIA2308E
Oil pan bolts : 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA4113E
Drain plug : 34 N·m (3.5 kg-m, 25 ft-lb)

ASSEMBLYAT-321
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
16. Install the oil pan magnets as shown.
17. Install the oil pan and new oil pan gasket.
CAUTION:

Do not reuse the oil pan gasket.

Completely remove all moisture, oil and old gasket from
the oil pan gasket mating surfaces and holes.

Always replace the oil pan bolts as they are self-sealing.

Be sure the oil pan drain plug hole is located to the rear
of the transmission assembly.

Partially install the oil pan bolts in a criss-cross pattern to
prevent dislocation of the gasket.

Be careful not to pinch harnesses.
18. Tighten new oil pan bolts in numerical order as shown.
19. Install drain plug in oil pan with new gasket. CAUTION:
Do not reuse the drain plug gasket.
20. Install torque converter.
a. Pour ATF into torque converter.

Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of fluid is
required for a new torque converter.

When reusing old torque converter, add the same amount
of fluid as was drained.
SCIA5200E
SCIA2308E
Oil pan bolts : 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA4113E
Drain plug : 34 N·m (3.5 kg-m, 25 ft-lb)
SAT428DA

FFD-28
FRONT FINAL DRIVE ASSEMBLY
Revision: November 20092006 QX56
4. Install the pinion mate shaft and align the lock pin hole on the
pinion mate shaft with the lock pin hole on the differential case.
5. Measure the side gear end play. If necessary, select the appro- priate side gear thrust washers. Refer to FFD-23, "
Side Gear
Back Clearance" .
6. Drive a new lock pin into the pinion mate shaft until it is flush with the differential case using suitable tool.
CAUTION:
Do not reuse lock pin.
7. Align the matching mark of the differential case with the mark of the drive gear, then place the drive gear onto the differential
case.
8. Install and tighten the new drive gear bolts to the specified torque. Refer to FFD-14, "
COMPONENTS" .
CAUTION:

Make sure the drive gear back and threaded holes are
clean.

Do not reuse drive gear bolts.

Tighten new drive gear bolts in a crisscross pattern.
9. Press the new side bearing inner races to the differential case using Tools.
CAUTION:
Do not reuse side bearing inner races.
SDIA0195J
SPD030
SDIA2593E
SDIA2239E
Tool number A: KV38100300 (J-25523)
B: ST33081000
SPD353

REAR FINAL DRIVE ASSEMBLYRFD-29
CE F
G H
I
J
K L
M A
B
RFD
Revision: November 2009 2006 QX56
7. Align the matching mark of the differential case with the mark of
the drive gear, then place the drive gear onto the differential
case.
8. Apply thread locking sealant into the threaded holes of the drive gear and install the bolts.

Use Genuine Medium Strength Thread Locking Sealant or
equivalent. Refer to GI-46, "
Recommended Chemical Prod-
ucts and Sealants" .
CAUTION:
Make sure the drive gear back and threaded holes are
clean.
9. Tighten the drive gear bolts to the specified torque. Refer to RFD-15, "
COMPONENTS" . After tightening the drive gear bolts
to the specified torque, tighten an additional 34 ° using Tool.
CAUTION:

Always use Tool. Avoid tightening based on visual check
alone.

Tighten drive gear bolts in a crisscross pattern.
10. Press the side bearing inner races into the differential case using Tools.
CAUTION:
Do not reuse side bearing inner race.
11. Install the differential case assembly with the side bearing outer races into the gear carrier.
12. Measure the side bearing preload torque. If necessary, select the appropriate side bearing adjusting washers. Refer to RFD-
24, "Side Bearing Preload Torque" .
SDIA2593E
SDIA2594E
Tool number : KV10112100-A (BT-8653-A)
SDIA0247J
Tool number A: KV38100200 (J-26233)
B: ST33081000 ( — )
SPD353
SPD919