turn signal INFINITI QX56 2006 Factory Service Manual

ACS-26
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: November 20092006 QX56
CONSULT-II Function (ICC)EKS00BLX
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3. Turn ignition switch ON.
4. Touch “START (NISSAN BASED VHCL) ”.
5. Touch “ICC” on "SELECT SYSTEM" screen.
If “ICC ” is not indicated, go to GI-40, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
ICC diagnostic mode Description
WORK SUPPORT Supports inspections and adjustments. Commands are transmitted to the ICC unit for setting the sta-
tus suitable for required operation, input/output signals are received from the ICC unit and received
data is displayed.
SELF-DIAG RESULTS Displays ICC unit self-diagnosis results. DATA MONITOR Displays ICC unit input/output data in real-time.
CAN DIAG SUPPORT MNTR The results of transmit/receive diagnosis of CAN communication can be read. ACTIVE TEST Operation of electrical loads can be checked by sending driving signal to them.
ECU PART NUMBER ICC unit part number can be read.
BBIA0369E
BCIA0029E
BCIA0030E

TROUBLE DIAGNOSIS — GENERAL DESCRIPTIONACS-33
[ICC]
C
DE
F
G H
I
J
L
M A
B
ACS
Revision: November 2009 2006 QX56

When multiple malfunctions are detected, a maximum of 3 code numbers can be stored; the lat-
est malfunction will be displayed first.
6. Check ACS-36, "
Diagnostic Trouble Code (DTC) Chart" , and repair or replace if necessary.
7. After repair, erase DTC stored in the ICC unit. Refer to ACS-33, "
Self-Diagnostic Erasing Method"
8. DTC 55 will be shown.
9. Turn ignition switch OFF to exit the diagnosis.
10. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
Self-Diagnostic Erasing Method
1. Stop the vehicle and turn the ignition switch OFF.
2. Turn ignition switch ON and start self-diagnosis.
3. During self-diagnosis mode, press CANCEL switch 5 times, and DISTANCE switch 5 times within a 10second time period.
CAUTION:

Switch inputs must be received within a 10 second time period.

When operation is not completed within 10 seconds start again from step 1.
4. DTC 55 will be shown. CAUTION:
DTC of an existing malfunction will not be erased.
5. Turn ignition switch OFF to exit the diagnosis.
6. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC system warning lamp (orange) does not illuminate.
SELF-DIAGNOSIS BY ICC SYSTEM DISPLAY WILL NOT RUN
Self Diagnosis Will Not Run
WKIA1985E
Component Possible Cause Specific causes
ICC unit power supply malfunction No voltage supply from ignition switchFuse blown
Harness open
Harness shorted
Ground cable not connected Harness open
Harness shorted
ICC steering switch malfunction No signal transmittedHarness open
Harness shorted
Spiral cable open
Spiral cable shorted
Switch or ECM malfunction
CAN communication system malfunction Signal not transmitted Harness open
Harness shorted
CAN communication outside the standard

ACS-42
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: November 20092006 QX56
2. CHECK ICC STEERING SWITCH
Check ICC steering switch. Refer to ACS-58, "
ICC Steering Switch" .
OK or NG
OK >> GO TO 3.
NG >> Replace ICC steering switch assembly. Refer to ACS-59, "
ICC Steering Switch" . Erase DTC and
perform ICC system running test. Refer to ACS-9, "
ICC System Running Test" . Then perform
self-diagnosis of ICC system again.
3. CHECK ICC STEERING SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM and spiral cable connectors.
3. Check continuity between ECM harness connectors E16 and F54 terminals 67, 99 and spiral cable harness connector M30
terminals 33, 34.
OK or NG
OK >> GO TO 4.
NG >>

Repair harness between ECM and spiral cable.

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
4. CHECK ICC STEERING SWITCH SIGNAL CIRCUIT
1. Disconnect remaining spiral cable connector.
2. Check continuity between spiral cable (A) (to vehicle) terminals 33, 34 and spiral cable (B) (to switch) terminals 14,15.
OK or NG
OK >> Replace ECM. Erase DTC and perform ICC system run- ning test. Refer to ACS-9, "
ICC System Running Test" .
Then perform self-diagnosis of ICC system again.
NG >>

Replace spiral cable. Refer to SRS-48, "Removal and
Installation" .

Erase DTC and perform ICC system running test.
Refer to ACS-9, "
ICC System Running Test" . Then
perform self-diagnosis of ICC system again.
DTC 74 LASER BEAM OFF CNTREKS00BM8
1. DIAGNOSTIC CHECK
1. Adjust laser beam aiming. Refer to ACS-12, "
LASER BEAM AIMING ADJUSTMENT" . Erase DTC and
perform ICC system running test. Refer to ACS-9, "
ICC System Running Test" .
2. Perform self-diagnosis of ICC system. Is DTC 74 LASER BEAM OFF CNTR indicated?
YES or NO
YES >>
Replace ICC sensor and adjust laser beam aiming. Refer to ACS-59, "ICC Sensor" .

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
NO >> Inspection end. 67 - 33, 99 - 34
Continuity should exist.
WKIA1928E
34 - 14, 33 - 15Continuity should exist.
WKIA4572E

ACS-48
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: November 20092006 QX56
DTC 96 NP RANGEEKS00BMB
1. CHECK ICC UNIT CONNECTORS
1. Turn ignition switch OFF.
2. Disconnect ICC unit harness connectors and connect them securely again. Erase DTC, then perform self- diagnosis of ICC system again.
OK or NG
OK >> GO TO 2.
NG >>

Poor connector connection.

Check connector. Check connector housing for disconnected, loose, bent, and collapsed termi-
nals. If any malfunction is detected, repair as necessary. Erase DTC and perform ICC system
running test. Refer to ACS-9, "
ICC System Running Test" . Then perform self-diagnosis of ICC
system again.
2. CHECK NP RANGE SWITCH SIGNAL
With CONSULT-II
With data monitor, check that “NP RANGE SW ” operates normally.
OK or NG
OK >> Perform TCM diagnosis. Refer to AT- 8 6 , "SELF-DIAGNOSTIC RESULT MODE" .
NG >> GO TO 3.
3. CHECK HARNESS BETWEEN ICC UNIT AND TCM
1. Turn ignition switch OFF.
2. Disconnect ICC unit harness connectors and A/T assembly har- ness connector.
3. Check continuity between ICC unit harness connector B13 ter- minal 7 and A/T assembly harness connector F9 terminal 9.
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase
DTC and perform ICC system running test. Refer to
ACS-9, "
ICC System Running Test" . Then perform self-
diagnosis of ICC system again.
NG >>

Repair harness between ICC unit and TCM.

Erase DTC and perform ICC system running test. Refer to ACS-9, "ICC System Running Test"
. Then perform self-diagnosis of ICC system again.
DTC 97 AT CIRCUITEKS00BMC
1. CHECK A/T CIRCUIT
With CONSULT-II
With TCM diagnosis, check that shift operates normally. Refer to AT- 1 0 5 , "
DTC P0705 PARK/NEUTRAL
POSITION SWITCH" .
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform self-diagnosis of ICC
system again.
NG >>

Perform TCM diagnosis.

Erase DTC and perform self-diagnosis of ICC system again.
7 - 9 Continuity should exist.
SKIA5982E

AT-3
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
DTC Confirmation Procedure ..............................
. 145
Diagnostic Procedure .......................................... . 146
DTC P1762 DIRECT CLUTCH SOLENOID VALVE . 147
Description .......................................................... . 147
CONSULT-II Reference Value ............................. . 147
On Board Diagnosis Logic .................................. . 147
Possible Cause ................................................... . 147
DTC Confirmation Procedure .............................. . 147
Diagnostic Procedure .......................................... . 148
DTC P1764 DIRECT CLUTCH SOLENOID VALVE
FUNCTION ............................................................. . 149
Description .......................................................... . 149
CONSULT-II Reference Value ............................. . 149
On Board Diagnosis Logic .................................. . 149
Possible Cause ................................................... . 149
DTC Confirmation Procedure .............................. . 149
Diagnostic Procedure .......................................... . 150
DTC P1767 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE ................................................ . 151
Description .......................................................... . 151
CONSULT-II Reference Value ............................. . 151
On Board Diagnosis Logic .................................. . 151
Possible Cause ................................................... . 151
DTC Confirmation Procedure .............................. . 151
Diagnostic Procedure .......................................... . 152
DTC P1769 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE FUNCTION ............................ . 153
Description .......................................................... . 153
CONSULT-II Reference Value ............................. . 153
On Board Diagnosis Logic .................................. . 153
Possible Cause ................................................... . 153
DTC Confirmation Procedure .............................. . 153
Diagnostic Procedure .......................................... . 154
DTC P1772 LOW COAST BRAKE SOLENOID
VALVE .................................................................... . 155
Description .......................................................... . 155
CONSULT-II Reference Value ............................. . 155
On Board Diagnosis Logic .................................. . 155
Possible Cause ................................................... . 155
DTC Confirmation Procedure .............................. . 155
Diagnostic Procedure .......................................... . 156
DTC P1774 LOW COAST BRAKE SOLENOID
VALVE FUNCTION ................................................ . 157
Description .......................................................... . 157
CONSULT-II Reference Value ............................. . 157
On Board Diagnosis Logic .................................. . 157
Possible Cause ................................................... . 157
DTC Confirmation Procedure .............................. . 157
Diagnostic Procedure .......................................... . 158
DTC P1841 ATF PRESSURE SWITCH 1 .............. . 159
Description .......................................................... . 159
CONSULT-II Reference Value ............................. . 159
On Board Diagnosis Logic .................................. . 159
Possible Cause ................................................... . 159
DTC Confirmation Procedure .............................. . 159
Diagnostic Procedure .......................................... . 160
DTC P1843 ATF PRESSURE SWITCH 3 .............. . 161
Description .......................................................... . 161
CONSULT-II Reference Value ............................. . 161On Board Diagnosis Logic ...................................
.161
Possible Cause .................................................... .161
DTC Confirmation Procedure .............................. .161
Diagnostic Procedure .......................................... .162
DTC P1845 ATF PRESSURE SWITCH 5 .............. .163
Description ........................................................... .163
CONSULT-II Reference Value ............................. .163
On Board Diagnosis Logic ................................... .163
Possible Cause .................................................... .163
DTC Confirmation Procedure .............................. .163
Diagnostic Procedure .......................................... .164
DTC P1846 ATF PRESSURE SWITCH 6 .............. .165
Description ........................................................... .165
CONSULT-II Reference Value ............................. .165
On Board Diagnosis Logic ................................... .165
Possible Cause .................................................... .165
DTC Confirmation Procedure .............................. .165
Diagnostic Procedure .......................................... .166
MAIN POWER SUPPLY AND GROUND CIRCUIT .167
Wiring Diagram — AT — MAIN ........................... .167
Diagnostic Procedure .......................................... .168
CLOSED THROTTLE POSITION AND WIDE OPEN
THROTTLE POSITION CIRCUIT ........................... .171
CONSULT-II Reference Value ............................. .171
Diagnostic Procedure .......................................... .171
BRAKE SIGNAL CIRCUIT ..................................... .172
CONSULT-II Reference Value ............................. .172
Diagnostic Procedure .......................................... .172
TOW MODE SWITCH ............................................ .173
Description ........................................................... .173
Wiring Diagram — AT — TMSW ......................... .174
Diagnostic Procedure .......................................... .175
TROUBLE DIAGNOSIS FOR SYMPTOMS ........... .176
Wiring Diagram — AT — NONDTC ..................... .176
A/T CHECK Indicator Lamp Does Not Come On . 179
Engine Cannot Be Started In “P” or “N” Position . .179
In “P” Position, Vehicle Moves When Pushed ..... .180
In “N” Position, Vehicle Moves ............................. .181
Large Shock (“N” to “D” Position) ........................ .182
Vehicle Does Not Creep Backward In “R” Position .186
Vehicle Does Not Creep Forward In “D” Position . 189
Vehicle Cannot Be Started From D
1 .................... .191
A/T Does Not Shift: D
1 → D2 ............................... .194
A/T Does Not Shift: D
2 → D3 ............................... .196
A/T Does Not Shift: D
3 → D4 ............................... .198
A/T Does Not Shift: D
4 → D5 ............................... .201
A/T Does Not Perform Lock-up ........................... .203
A/T Does Not Hold Lock-up Condition ................. .205
Lock-up Is Not Released ..................................... .207
Engine Speed Does Not Return to Idle ............... .208
A/T Does Not Shift: 5th gear → 4th gear ............. .209
A/T Does Not Shift: 4th gear → 3rd gear ............. .212
A/T Does Not Shift: 3rd gear → 2nd gear ............ .213
A/T Does Not Shift: 2nd gear → 1st gear .............215
Vehicle Does Not Decelerate By Engine Brake ... .218
A/T SHIFT LOCK SYSTEM ................................... .221
Description ........................................................... .221
Shift Lock System Electrical Parts Location ........ .221
Wiring Diagram — A/T — SHIFT ......................... .222

AT-38
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: November 20092006 QX56
ON BOARD DIAGNOSTIC (OBD) SYSTEMPFP:00028
IntroductionECS00CE4
The A/T system has two self-diagnostic systems.
The first is the emission-related on board diagnostic system (OBD-II) performed by the TCM in combination
with the ECM. The malfunction is indicated by the MIL (malfunction indicator lamp) and is stored as a DTC in
the ECM memory but not the TCM memory.
The second is the TCM original self-diagnosis indicated by the A/T CHECK indicator lamp. The malfunction is
stored in the TCM memory. The detected items are overlapped with OBD-II self-diagnostic items. For detail,
refer to AT- 8 6 , "
SELF-DIAGNOSTIC RESULT MODE" .
OBD-II Function for A/T SystemECS00CE5
The ECM provides emission-related on board diagnostic (OBD-II) functions for the A/T system. One function
is to receive a signal from the TCM used with OBD-related parts of the A/T system. The signal is sent to the
ECM when a malfunction occurs in the corresponding OBD-related part. The other function is to indicate a
diagnostic result by means of the MIL (malfunction indicator lamp) on the instrument panel. Sensors, switches
and solenoid valves are used as sensing elements.
The MIL automatically illuminates in One or Two Trip Detection Logic when a malfunction is sensed in relation
to A/T system parts.
One or Two Trip Detection Logic of OBD-IIECS00CE6
ONE TRIP DETECTION LOGIC
If a malfunction is sensed during the first test drive, the MIL will illuminate and the malfunction will be stored in
the ECM memory as a DTC. The TCM is not provided with such a memory function.
TWO TRIP DETECTION LOGIC
When a malfunction is sensed during the first test drive, it is stored in the ECM memory as a 1st trip DTC
(diagnostic trouble code) or 1st trip freeze frame data. At this point, the MIL will not illuminate. — 1st Trip
If the same malfunction as that experienced during the first test drive is sensed during the second test drive,
the MIL will illuminate. — 2nd Trip
The “Trip ” in the “One or Two Trip Detection Logic ” means a driving mode in which self-diagnosis is performed
during vehicle operation.
OBD-II Diagnostic Trouble Code (DTC)ECS00CE7
HOW TO READ DTC AND 1ST TRIP DTC
DTC and 1st trip DTC can be read by the following methods.
( with CONSULT-II or GST) CONSULT-II or GST (Generic Scan Tool) Examples: P0705, P0720 etc.
These DTC are prescribed by SAE J2012.
(CONSULT-II also displays the malfunctioning component or system.)

1st trip DTC No. is the same as DTC No.

Output of the diagnostic trouble code indicates that the indicated circuit has a malfunction. How-
ever, in case of the Mode II and GST, they do not indicate whether the malfunction is still occurring
or occurred in the past and returned to normal.
CONSULT-II can identify them as shown below, therefore, CONSULT-II (if available) is recom-
mended.
A sample of CONSULT-II display for DTC and 1st trip DTC is shown
on the next page. DTC or 1st trip DTC of a malfunction is displayed
in SELF-DIAGNOSTIC RESULTS mode for “ENGINE” with CON-
SULT-II. Time data indicates how many times the vehicle was driven
after the last detection of a DTC.
BCIA0030E

AT-42
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
TROUBLE DIAGNOSISPFP:00004
DTC Inspection Priority ChartECS00CE9
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 9 6
.
Fail-SafeECS00CEA
The TCM has an electrical fail-safe mode. This mode makes it possible to operate even if there is an error in a
main electronic control input/output signal circuit. In fail-safe mode the transmission is fixed in 2nd, 4th or 5th
(depending on the breakdown position), so the customer should feel “slipping” or “poor acceleration ”.
Even when the electronic circuits are normal, under special conditions (for example, when slamming on the
brake with the wheels spinning drastically and stopping the tire rotation), the transmission can go into fail-safe
mode. If this happens, switch “OFF ” the ignition switch for 10 seconds, then switch it “ON” again to return to
the normal shift pattern. Therefore, the customer's vehicle has returned to normal, so handle according to the
“diagnostics flow ” (Refer to AT- 4 5 , "
WORK FLOW" ).
FAIL-SAFE FUNCTION
If any malfunction occurs in a sensor or solenoid, this function controls the A/T to make driving possible.
Vehicle Speed Sensor

Signals are input from two systems - from vehicle speed sensor A/T (revolution sensor) installed on the
transmission and from combination meter so normal driving is possible even if there is a malfunction in
one of the systems. And if vehicle speed sensor A/T (revolution sensor) has unusual cases, 5th gear is
prohibited.
Accelerator Pedal Position Sensor

If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM accord-
ing to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow
systems, the engine speed is fixed by ECM to a pre-determined engine speed to make driving possible.
Throttle Position Sensor

If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM accord-
ing to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow
systems, the accelerator opening angle is controlled by the idle signal sent from the ECM which is based
on input indicating either idle condition or off-idle condition (pre-determined accelerator opening) in order
to make driving possible.
PNP Switch

In the unlikely event that a malfunction signal enters the TCM, the position indicator is switched “OFF”, the
starter relay is switched “OFF ” (starter starting is disabled), the back-up lamp relay switched “OFF” (back-
up lamp is OFF) and the position is fixed to the “D” range to make driving possible.
Starter Relay

The starter relay is switched “OFF”. (Starter starting is disabled.)
Priority Detected items (DTC)
1 U1000 CAN communication line
2 Except above

TROUBLE DIAGNOSISAT-47
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
4❏
Perform all road tests and enter checks in required inspection items. AT- 5 4
4-1.Check before engine is started
AT- 5 5
❏ AT- 1 7 9 , "A/T CHECK Indicator Lamp Does Not Come On" .
❏ Perform self-diagnostics Enter checks for detected items. AT- 8 6
❏ AT-96, "DTC U1000 CAN COMMUNICATION LINE"
❏ AT-100, "DTC P0615 START SIGNAL CIRCUIT"
❏ AT-104, "DTC P0700 TCM"
❏ AT-105, "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ AT-109, "DTC P0717 TURBINE REVOLUTION SENSOR"
❏ AT- 111 , "DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)"
❏ AT-116, "DTC P0725 ENGINE SPEED SIGNAL"
❏ AT-118, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ AT-120, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ AT-122, "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ AT-124, "DTC P1705 THROTTLE POSITION SENSOR"
❏ AT-127, "DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT"
❏ AT-132, "DTC P1721 VEHICLE SPEED SENSOR MTR"
❏ AT-134, "DTC P1730 A/T INTERLOCK"
❏ AT-137, "DTC P1731 A/T 1ST ENGINE BRAKING"
❏ AT-139, "DTC P1752 INPUT CLUTCH SOLENOID VALVE"
❏ AT-141, "DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-143, "DTC P1757 FRONT BRAKE SOLENOID VALVE"
❏ AT-145, "DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION"
❏ AT-147, "DTC P1762 DIRECT CLUTCH SOLENOID VALVE"
❏ AT-149, "DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-151, "DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE"
❏ AT-153, "DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION"
❏ AT-155, "DTC P1772 LOW COAST BRAKE SOLENOID VALVE"
❏ AT-157, "DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION"
❏ AT-159, "DTC P1841 ATF PRESSURE SWITCH 1"
❏ AT-161, "DTC P1843 ATF PRESSURE SWITCH 3"
❏ AT-163, "DTC P1845 ATF PRESSURE SWITCH 5"
❏ AT-165, "DTC P1846 ATF PRESSURE SWITCH 6"
4-2. Idle inspection
AT- 5 5
❏ AT- 1 7 9 , "Engine Cannot Be Started In “P” or “N” Position"
❏ AT- 1 8 0 , "In “P” Position, Vehicle Moves When Pushed"
❏ AT- 1 8 1 , "In “N” Position, Vehicle Moves"
❏ AT- 1 8 2 , "Large Shock (“N” to “D” Position)"
❏ AT- 1 8 6 , "Vehicle Does Not Creep Backward In “R” Position"
❏ AT- 1 8 9 , "Vehicle Does Not Creep Forward In “D” Position"
4-3. Driving tests
AT- 5 6
Part 1
❏ AT- 1 9 1 , "
Vehicle Cannot Be Started From D1"
❏ AT- 1 9 4 , "A/T Does Not Shift: D1 → D2"
❏ AT- 1 9 6 , "A/T Does Not Shift: D2 → D3"
❏ AT- 1 9 8 , "A/T Does Not Shift: D3 → D4"
❏ AT- 2 0 1 , "A/T Does Not Shift: D4 → D5"
❏ AT- 2 0 3 , "A/T Does Not Perform Lock-up"
❏ AT- 2 0 5 , "A/T Does Not Hold Lock-up Condition"
❏ AT- 2 0 7 , "Lock-up Is Not Released"
❏ AT- 2 0 8 , "Engine Speed Does Not Return to Idle"

AT-58
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
6. CHECK LOCK-UP
When releasing accelerator pedal from D5, check lock-up from D5 to L/U.

Refer to AT- 6 0 , "Vehicle Speed When Shifting Gears" .
With CONSULT-II
Select “TCC SOLENOID 0.00A ” with the “MAIN SIGNAL ” mode for A/T.
Does it lock-up?
YES >> GO TO 7.
NO >> Enter a check mark at “A/T Does Not Perform Lock-up” on the diagnostics worksheet, then con-
tinue the road test.
7. CHECK LOCK-UP HOLD
Does it maintain lock-up status?
YES >> GO TO 8.
NO >> Enter a check mark at “A/T Does Not Hold Lock-up Condition ” on the diagnostics worksheet, then
continue the road test.
8. CHECK LOCK-UP RELEASE
Check lock-up cancellation by depressing brake pedal lightly to decelerate. With CONSULT-II
Select “TCC SOLENOID 0.00A ” with the “MAIN SIGNAL ” mode for A/T.
Does lock-up cancel?
YES >> GO TO 9.
NO >> Enter a check mark at “Lock-up Is Not Released” on the diagnostics worksheet, then continue the
road test.
9. CHECK SHIFT-DOWN D5 → D4
Decelerate by pressing lightly on the brake pedal. With CONSULT-II
Read the gear position and engine speed.
When the A/T shift-down D5
→ D4, does the engine speed drop smoothly back to idle?
YES >> 1. Stop the vehicle.
2. Go to Cruise test - Part 2 (Refer to AT- 5 8
).
NO >> Enter a check mark at “Engine Speed Does Not Return to Idle” on the diagnostics worksheet, then continue the road test. Go to Cruise test - Part 2 (Refer to AT- 5 8
).
Cruise Test - Part 2ECS00CEI
1. CHECK STARTING FROM D1
1. Move selector lever the “D ” position.
2. Accelerate at half throttle.
With CONSULT-II
Read the gear position.
Does it start from D1?
YES >> GO TO 2.
NO >> Enter a check mark at “Vehicle Cannot Be Started From D1 ” on the diagnostics worksheet, then
continue the road test.

TROUBLE DIAGNOSISAT-87
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
2. Touch “SELF-DIAG RESULTS ”.
Display shows malfunction experienced since the last erasing
operation.
Display Items List
X: Applicable, —: Not applicable
BCIA0031E
Items (CONSULT-II
screen terms) Malfunction is detected when... TCM self-
diagnosis OBD-II (DTC)
“ A/T ” with
CONSULT-II MIL indicator
lamp*1,
“ ENGINE ” with
CONSULT-II or
GST
CAN COMM CIRCUIT

When a malfunction is detected in CAN communications U1000 U1000
STARTER RELAY/
CIRC

If this signal is ON other than in P or N position, this is judged to be a
malfunction.
(And if it is OFF in P or N position, this too is judged to be a malfunc-
tion.) P0615
—
TCM

TCM is malfunctioning. P0700 P0700
PNP SW/CIRC

PNP switch 1-4 signals input with impossible pattern

“ P ” position is detected from N position without any other position
being detected in between. P0705 P0705
TURBINE REV S/CIRC

TCM does not receive the proper voltage signal from the sensor.

TCM detects an irregularity only at position of 4th gear for turbine revo-
lution sensor 2. P0717 P0717
VEH SPD SEN/CIR AT
(Revolution sensor)

Signal from vehicle speed sensor A/T (Revolution sensor) not input
due to cut line or the like

Unexpected signal input during running

After ignition switch is turned ON, unexpected signal input from vehicle
speed sensor MTR before the vehicle starts moving P0720 P0720
ENGINE SPEED SIG

TCM does not receive the CAN communication signal from the ECM. P0725 —
TCC SOLENOID/CIRC

Normal voltage not applied to solenoid due to cut line, short, or the like P0740 P0740
A/T TCC S/V FNCTN

A/T cannot perform lock-up even if electrical circuit is good.

TCM detects as irregular by comparing difference value with slip rota-
tion. P0744 P0744*2
L/PRESS SOL/CIRC

Normal voltage not applied to solenoid due to cut line, short, or the like

TCM detects as irregular by comparing target value with monitor value. P0745 P0745
TP SEN/CIRC A/T

TCM does not receive the proper accelerator pedal position signals
(input by CAN communication) from ECM. P1705 P1705
ATF TEMP SEN/CIRC

During running, the ATF temperature sensor signal voltage is exces-
sively high or low P1710 P0710
VEH SPD SE/CIR ·MTR

Signal (CAN communication) from vehicle speed sensor MTR not input
due to cut line or the like

Unexpected signal input during running P1721
—
A/T INTERLOCK

Except during shift change, the gear position and ATF pressure switch
states are monitored and comparative judgement made. P1730 P1730