Abs INFINITI QX56 2009 Factory Service Manual

CCS-26
< COMPONENT DIAGNOSIS >
DTC 41 VHCL SPEED SE CIRC
DTC 41 VHCL SPEED SE CIRC
DTC 41 VHCL SPEED SE CIRCINFOID:0000000003776941
1.PERFORM ICC UNIT SELF-DIAGNOSIS
Perform self-diagnosis.
Is
“DTC 43 VDC/TCS/ABS CIRC” or “DTC 20 CAN COMM CIRCUIT” indicated in self-diagnosis item display?
YES >> Repair or replace as necessary. Erase DT C and perform ICC system running test. Refer to CCS-
8, "ACTION TEST : ICC System Running Test".
NO >> GO TO 2
2.CHECK A/T VEHICLE SPEED SENSOR
With data monitor, check “VHCL SPD AT”.
Does the data monitor item work normally?
YES >> Replace ICC unit. Refer to CCS-70, "ICC Unit". Erase DTC and perform ICC system running test.
Refer to CCS-8, "
ACTION TEST : ICC System Running Test".
NO >> • Check TCM. • Erase DTC and perform ICC system running test. Refer to CCS-8, "
ACTION TEST : ICC Sys-
tem Running Test" .
Revision: December 20092009 QX56

CCS
DTC 43 VDC/TCS/ABS CIRCCCS-27
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B
N P A
DTC 43 VDC/TCS/ABS CIRC
DTC 43 VDC/TCS/ABS CIRCINFOID:0000000003776942
1.DIAGNOSIS CHECK 1
Perform self-diagnosis.
Is
“CAN COMM CIRCUIT” indicated?
YES >> Repair or replace as necessary. Erase DTC and perform ICC system running test. Refer to CCS-
8, "ACTION TEST : ICC System Running Test".
NO >> GO TO 2
2.DIAGNOSIS CHECK 2
Perform self-diagnosis of ABS actuator and electric unit (control unit).
Is malfunction indicated?
YES >> Repair the ABS system as necessary. Erase DTC and perform ICC system running test. Refer to
CCS-8, "
ACTION TEST : ICC System Running Test" .
NO >> Replace ICC unit. Refer to CCS-70, "
ICC Unit". Erase DTC and perform ICC system running test.
Refer to CCS-8, "
ACTION TEST : ICC System Running Test".
Revision: December 20092009 QX56

CCS-40
< COMPONENT DIAGNOSIS >
DTC 98 GEAR POSITION
DTC 98 GEAR POSITION
DTC 98 GEAR POSITIONINFOID:0000000003776950
1.DIAGNOSTIC CHECK
Perform ICC self diagnosis.
Does "DTC 43 VDC/TCS/ABS CIRC" or "DTC 41 VHCL SP EED SE CIRC" indicated in self-diagnosis display
item?
YES >> Repair or replace as necessary. Erase DTC and perform self-diagnosis of ICC system again.
NO >> GO TO 2
2.CHECK VEHICLE SPEED SIGNAL
With data monitor, check that “VHCL SPEED SE” is normal.
Does the "VHCL SPEED SE" monitor item display normally?
YES >> GO TO 3
NO >> Replace ICC unit. Refer to CCS-70, "
ICC Unit". Erase DTC and perform self-diagnosis of ICC sys-
tem again.
3.CHECK GEAR SHIFT POSITION
Check that gear positions are correct in A/T.
Does the transmission operate normally?
YES >> GO TO 5
NO >> GO TO 4
4.CHECK TCM GEAR POSITION SIGNAL
With TCM data monitor, check that gear positions are correct.
Does the data monitor indicate proper gear positions?
YES >> Replace ICC unit. Refer to CCS-70, "ICC Unit".
NO >> • Perform TCM diagnosis.
• Erase DTC and perform self-d iagnosis of ICC system again.
5.CHECK TCM TURBINE ROTATION
With TCM diagnosis, check that turbine rpm is normal. Refer to TM-47, "
Description".
Does the TCM check OK?
YES >> Replace ICC unit. Refer to CCS-70, "ICC Unit".
NO >> • Perform TCM diagnosis.
• Erase DTC and perform self-d iagnosis of ICC system again. CCS-17, "
Diagnosis Description"
Revision: December 20092009 QX56

CCS
ICC UNITCCS-55
< ECU DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B
N P A
Diagnostic Trouble Code (DTC) ChartINFOID:0000000003776959
× :Applicable
DTC
No. CONSULT-III screen terms ICC sys-
tem
warning lamp Fail-safe
Malfunctions detected where... Refer-
ence
page
Veh ic le-
to-vehi-cle dis-
tance
control mode Conven-
tional
(fixed
speed) cruise
control mode Brake as-
sist (with
preview
function)
11 CONTROL UNIT ×××× • ICC unit internal malfunctionCCS-22
12 VDC CONTROL UNIT ×××× • VDC malfunction
• Brake booster signal harness is
open or shorted CCS-23
20 CAN COMM CIRCUIT
×××× • ICC unit detected CAN communi-
cation malfunction CCS-24
31 POWER SUPPLY CIR1
×××× • ICC unit power supply voltage is
excessively low (less than 8V) CCS-25
34 POWER SUPPLY CIR2
×××× • ICC unit power supply voltage is
excessively high. CCS-25
41 VHCL SPEED SE CIRC
×××× • Wheel sensor malfunction
• ABS actuator and electric unit
(control unit) malfunction
• A/T vehicle speed sensor mal-
function
•TCM malfunction CCS-26
43 VDC/TCS/ABS CIRC
×××× • VDC/TCS/ABS system malfunc-
tion CCS-27
45 BRAKE SW/ STOP L SW
×××× • ICC brake switch or stop lamp
switch harness is open or shorted
• ICC brake switch or stop lamp switch is stuck to OFF
• ICC brake switch or stop lamp switch is stuck to ON CCS-28
46 OPERATION SW CIRC
××× • ICC steering switch harness or
spiral cable is open or shorted
• ICC steering switch malfunction CCS-30
74 LASER BEAM OFF CNTR
××ו Laser beam of ICC sensor is off
the aiming point CCS-31
90 STOP LAMP RLY FIX
××ו Normally open terminal of stop
lamp relay is stuck CCS-32
92 ECM CIRCUIT
×××× •ECM malfunction
• Accelerator pedal position sensor
malfunction
• ICC unit malfunction CCS-37
96 NP RANGE
××× • Transmission range switch har-
ness is open or shorted
• Transmission range switch mal- function
•TCM malfunction CCS-38
97 AT CIRCUIT
××× •TCM malfunctionCCS-39
98 GEAR POSITION ××× •TCM malfunction
• Input speed sensor malfunction
• A/T vehicle speed sensor mal-
function CCS-40
102 LASER STAIN
×× × • ICC sensor body window has
contamination CCS-41
Revision: December 20092009 QX56

CO-16
< ON-VEHICLE REPAIR >
RADIATOR
Do not allow coolant to contact drive belt.
5. Remove the lower radiator shroud. • Release the tabs, pull lower radiator shroud rearwards and
down to remove.
6. Disconnect the radiator upper hose and the coolant reservoir hose from the radiator. CAUTION:
Do not allow coolant to contact drive belt.
7. Remove the radiator shroud upper bolts and remove the radiator shroud upper (A).
8. Remove the upper radiator mounting bolts and rubbers.
9. Remove the A/C condenser bolts and brackets. NOTE:
Lift A/C condenser up and forward to remove from radiator.
10. Remove A/T oil cooler bolts and oil cooler from radiator and position aside.
WBIA0407E
WBIA0695E
WBIA0395E
WBIA0396E
Revision: December 20092009 QX56

DLK-58
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000003775708
CAN (Controller Area Network) is a serial communication
line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-44, "
CAN Communication Signal Chart".
DTC LogicINFOID:0000000003775709
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000003775710
1.PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “Self Diagnostic Result”.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-38, "
Intermittent Incident".
DTCCONSULT-III display
description DTC Detection Condition
Possible cause
U1000 CAN COMM CIRCUIT When BCM cannot communicate CAN com-
munication signal continuously for 2 sec-
onds or more. In CAN communication system, any item (or items)
of the following listed below is malfunctioning.
•Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (MULTI AV)
• Receiving (IPDM E/R)
Revision: December 20092009 QX56

DLN-1
TRANSMISSION & DRIVELINE
CEF
G H
I
J
K L
M
SECTION DLN
A
B
DLN
N
O P
CONTENTS
DRIVELINE
ATX14B
BASIC INSPECTION ....... .............................
6
DIAGNOSIS AND REPAIR WORKFLOW ..... .....6
Work Flow ........................................................... ......6
Preliminary Check .....................................................7
FUNCTION DIAGNOSIS ..............................10
4WD SYSTEM ................................................ ....10
System Diagram .................................................. ....10
System Description .................................................11
Component Parts Location ......................................16
CAN Communication ...............................................17
DIAGNOSIS SYSTEM (TRANSFER CON-
TROL UNIT) ........................................................
18
CONSULT-III Function (ALL MODE AWD/4WD) ....18
COMPONENT DIAGNOSIS .........................22
P1811 POWER SUPPLY CIRCUIT FOR
TRANSFER CONTROL UNIT ........................ ....
22
Description .......................................................... ....22
DTC Logic ...............................................................22
Diagnosis Procedure ...............................................22
Component Inspection ............................................23
P1802 – P1804, P1809 TRANSFER CON-
TROL UNIT .........................................................
24
Description .......................................................... ....24
DTC Logic ...............................................................24
Diagnosis Procedure ...............................................24
P1807 VEHICLE SPEED SENSOR (A/T) ..........26
Description .......................................................... ....26
DTC Logic ...............................................................26
Diagnosis Procedure ...............................................26
P1808 VEHICLE SPEED SENSOR (ABS) .........27
Description .......................................................... ....27
DTC Logic ............................................................ ....27
Diagnosis Procedure ...............................................27
P1810 NEUTRAL-4LO SWITCH .......................28
Description ...............................................................28
DTC Logic ................................................................28
Diagnosis Procedure ...............................................28
Component Inspection .............................................30
P1813 4WD SHIFT SWITCH .............................31
Description ...............................................................31
DTC Logic ................................................................31
Diagnosis Procedure ...............................................31
Component Inspection .............................................33
P1814 WAIT DETECTION SWITCH .................35
Description ...............................................................35
DTC Logic ................................................................35
Diagnosis Procedure ...............................................35
Component Inspection .............................................37
P1816 TRANSMISSION RANGE SWITCH .......38
Description ...............................................................38
DTC Logic ................................................................38
Diagnosis Procedure ...............................................38
P1817 ACTUATOR MOTOR .............................39
Description ...............................................................39
DTC Logic ................................................................39
Diagnosis Procedure ...............................................39
Component Inspection .............................................43
P1818 ACTUATOR POSITION SWITCH ..........45
Description ...............................................................45
DTC Logic ................................................................45
Diagnosis Procedure ...............................................45
Component Inspection .............................................47
P1819 TRANSFER CONTROL DEVICE ...........48
Description ...............................................................48
DTC Logic ................................................................48
Diagnosis Procedure ...........................................
....48
Revision: December 20092009 QX56

DLN-2
P1820 ENGINE SPEED SIGNAL ......................52
Description ........................................................... ...52
DTC Logic ...............................................................52
Diagnosis Procedure ..............................................52
P1822 CLUTCH PRESSURE SOLENOID .........53
Description ........................................................... ...53
DTC Logic ...............................................................53
Diagnosis Procedure ..............................................53
Component Inspection ............................................55
P1823 2-4 SOLENOID .......................................57
Description ........................................................... ...57
DTC Logic ...............................................................57
Diagnosis Procedure ..............................................57
Component Inspection ............................................60
P1824 TRANSFER MOTOR ..............................61
Description ........................................................... ...61
DTC Logic ...............................................................61
Diagnosis Procedure ..............................................61
Component Inspection ............................................65
P1826 TRANSFER FLUID TEMPERATURE ....67
Description ........................................................... ...67
DTC Logic ...............................................................67
Diagnosis Procedure ..............................................67
Component Inspection ............................................68
P1827 CLUTCH PRESSURE SWITCH .............70
Description ........................................................... ...70
DTC Logic ...............................................................70
Diagnosis Procedure ..............................................70
Component Inspection ............................................71
P1828 LINE PRESSURE SWITCH ....................73
Description ........................................................... ...73
DTC Logic ...............................................................73
Diagnosis Procedure ..............................................73
Component Inspection ............................................75
P1829 THROTTLE POSITION SIGNAL (ECM)
...
76
Description ........................................................... ...76
DTC Logic ...............................................................76
Diagnosis Procedure ..............................................76
P1830 ABS OPERATION SIGNAL (ABS) ........77
Description ........................................................... ...77
DTC Logic ...............................................................77
Diagnosis Procedure ..............................................77
P1831 VDC OPERATION SIGNAL (ABS) ........78
Description ........................................................... ...78
DTC Logic ...............................................................78
Diagnosis Procedure ..............................................78
P1832 TCS OPERATION SIGNAL (ABS) .........79
Description ........................................................... ...79
DTC Logic ...............................................................79
Diagnosis Procedure ..............................................79
U1010 CONTROL UNIT (CAN) .........................80
Description ........................................................... ...80
DTC Logic ...............................................................80
Diagnosis Procedure ...............................................80
ECU DIAGNOSIS .......................................81
TRANSFER CONTROL UNIT ........................ ...81
Reference Value .................................................. ...81
Wiring Diagram .......................................................89
DTC Index ...............................................................97
SYMPTOM DIAGNOSIS ...........................102
4WD SYSTEM SYMPTOMS ........................... ..102
Symptom Table .................................................... .102
4WD SHIFT INDICATOR LAMP AND 4LO IN-
DICATOR LAMP DO NOT TURN ON ..............
103
Description ........................................................... .103
Diagnosis Procedure .............................................103
4WD WARNING LAMP DOES NOT TURN ON ..105
Description ........................................................... .105
Diagnosis Procedure .............................................105
4WD SHIFT INDICATOR LAMP OR 4LO INDI-
CATOR LAMP DO NOT CHANGE ...................
107
Description ........................................................... .107
Diagnosis Procedure .............................................107
ATP WARNING LAMP DOES NOT TURN ON ..109
Description ........................................................... .109
Diagnosis Procedure .............................................109
4WD SHIFT INDICATOR LAMP KEEPS
FLASHING ........................................................
111
Description ........................................................... .111
Diagnosis Procedure .............................................111
4WD WARNING LAMP FLASHES RAPIDLY ..112
Description ............................................................112
Diagnosis Procedure .............................................112
4WD WARNING LAMP FLASHES SLOWLY ..113
Description ............................................................113
Diagnosis Procedure .............................................113
HEAVY TIGHT-CORNER BRAKING SYMP-
TOM OCCURS ................................................ ..
114
Description ........................................................... .114
Diagnosis Procedure .............................................114
ATP SWITCH ....................................................116
Description ........................................................... .116
Diagnosis Procedure .............................................116
4WD SYSTEM DOES NOT OPERATE ............118
Description ........................................................... .118
Diagnosis Procedure .............................................118
Revision: December 20092009 QX56

4WD SYSTEMDLN-11
< FUNCTION DIAGNOSIS > [ATX14B]
C
EF
G H
I
J
K L
M A
B
DLN
N
O PSystem DescriptionINFOID:0000000003772076
CONTROL SYSTEM
ABS actuator and electric unit
(control unit) Transmits vehicle speed signal via CAN communication to transfer control unit.
TCM Transmits the following signal via CAN communication to transfer control unit.
 Output shaft revolution signal
 A/T position indicator signal (transmission range switch signal)
ECM Transmits the following signals via CAN communication to transfer control unit.
 Engine speed signal
 Accelerator pedal position signal
Components Function
Revision: December 20092009 QX56

DIAGNOSIS SYSTEM (TRANSFER CONTROL UNIT)
DLN-19
< FUNCTION DIAGNOSIS > [ATX14B]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
12. Move A/T selector lever to N position.
13. Turn 4WD shift switch to AUTO position.
14. Move A/T selector lever to P position.
15. Read the flickering of 4WD warning lamp.
Self-diagnosis example
ERASE SELF-DIAGNOSIS
 In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned ON and OFF.
 However, this information is erased by turning igni tion switch OFF after performing self-diagnostics or by
erasing the memory using the CONSULT-III.
DATA MONITOR MODE
Operation Procedure
1. Connect CONSULT-III.
2. Touch DATA MONITOR.
3. Select from SELECT MONITOR ITEM, screen of data monitor mode is displayed.
NOTE:
When malfunction is detected, CONSUL T-III performs REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in th is mode will be displayed at real time.
Display Item List
×: Standard –: Not applicable
PDIA0227E
Monitored item (Unit) Monitor item selection
Remarks
ECU INPUT
SIGNALS MAIN
SIGNALS SELEC-
TION FROM MENU
VHCL/S SEN·FR [km/h] or [mph] ×–×Wheel speed calculated by ABS actuator and
electric unit (control unit).
Signal input with CAN communication line.
VHCL/S SEN·RR [km/h] or [mph] ×–×Wheel speed calculated by TCM.
Signal input with CAN communication line.
ENGINE SPEED [rpm] ×–×Engine speed calculated by ECM.
Signal input with CAN communication line.
THRTL POS SEN [V] ×–×Accelerator peda
l position (APP) sensor sig-
nal voltage is displayed.
Signal input with CAN communication line.
FLUID TEMP SE [V] ×–×Transfer fluid temperature sensor signal volt-
age is displayed.
BATTERY VOLT [V] ×–×Power supply voltage for transfer control unit.
2WD SWITCH [ON/OFF] ×–×4WD shift switch status is displayed.
AUTO SWITCH [ON/OFF] ×–×4WD shift switch status is displayed.
LOCK SWITCH [ON/OFF] ×–×4WD shift switch status is displayed.
(LOCK means 4H of 4WD shift switch.)
Revision: December 20092009 QX56