phone INFINITI QX56 2009 Factory User Guide

AV
HANDS-FREE PHONE SYSTEMAV-25
< FUNCTION DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
Component Parts LocationINFOID:0000000004109568
1. Front tweeter LH M109 2. Steering wheel audio control switch-
es 3. AV control unit M42, M43, M44, M45,
M97, M124, M125
4. Display unit M93 5. Center speaker M1106. A/C and AV switch assembly M98
7. Front tweeter RH M111 8. Aux jack M1049. Compact Flash insert slot
ALNIA0845ZZ
Revision: December 20092009 QX56

AV-26
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
HANDS-FREE PHONE SYSTEM
Component Description
INFOID:0000000003776787
10. Rear audio remote control unit R204 11. Microphone R109 12. Front door speaker
LH D12
RH D112
13. Rear door tweeter LH D208
RH D308 14. Rear door speaker
LH D207
RH D307 15. Back door speaker
LH D518
RH D716
16. Subwoofer B72 (under driver’s seat) 17. BOSE speaker amp M112, M113 (view behind instrument panel above
accelerator pedal)18. Rear view camera control unit B73
(located behind luggage finisher LHl)
19. Rear view camera D504
Part name Description
AV control unit • Receives telephone voice signal from Antenna and Microphone
• Sends telephone voice and voice guidance signals to the speakers
BOSE speaker amp. • Recieves audio signals from the AV control unit
• Outputs amplified audio signals to the speakers.
Front door speaker Receives telephone voice and voice guidance signals from the AV control unit
through the BOSE speaker amp.
Front tweeter
Center speaker
Steering switches • Start a voice recognition session
• Answer and end telephone calls
• Adjust the volume level
Microphone Sends voice signals to Bluetooth control unit
Bluetooth antenna Sends telephone voice signal to Bluetooth control unit
Revision: December 20092009 QX56

AV-28
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “SETTING” button, turn the volume control
dial counterclockwise 30 clicks or more.
CONFIRMATION/
ADJUSTMENT Display diagnosis
Color spectrum bar Color tone of the screen can be checked by the display of a color bar.
Gradation bar Shading of the screen can be checked by the display of a gray scale.
Touch panel
• Touch panel calibration
• Touch panel response check
Vehicle signals The following vehicle signals are analyzed: Vehicle speed signal, park-
ing brake signal, light signal, ignition switch signal, and reverse signal.
Speaker test Connection can be checked by sending a test tone to each speaker.
Navigation Steering angle ad-
justment
Confirm/adjust the steering angle when there is a difference between
the displayed vehicle mark turning angle and actual.
Speed calibration Confirm/adjust the speed calibration when there is a difference between
the displayed vehicle mark location and actual.
XM SAT subscrip-
tion status Check the subscription status of the XM NAV Traffic subsription.
Error history Diagnosis results previously stored in the memory are displayed in this
mode.
Synchronize FES clock Turns FES (Familly Entertainment System) clock synchronization func-
tion ON/OFF.
Vehicle CAN diagnosis The transmitting/receiving of CAN communication can be monitored.
AV COMM diagnosis The transmitting/receiving of AV communication can be monitored.
Handsfree phone Handsfree volume
adjustment
Adjust handsfree volume (low, medium, high).
Voice microphone
test Test microphone operation.
Delete handsfree
memory Erase handsfree system memory.
Bluetooth Confirm/Change
passkey
Confirm and change the Bluetooth passkey
Confirm/Change
device name Confirm and change a device name stored in Bluetooth.
SAT Change channel
Any necessary channels required to recieve traffic information from the
satellite radio system can be set.
Change applica-
tion ID Any application ID’s required to recieve traffic information from the sat-
ellite radio system can be set.
Diag Not used.
Delete unit connection log Erase the error history and connection history of the unit.
Initialize settings All audio settings are reset to default levels.
Mode
Description
ALNIA0446GB
Revision: December 20092009 QX56

AV-36
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Vehicle CAN Diagnosis
• CAN communication status and error counter is displayed.
• The error counter displays “OK” if any malfunction was not
detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
• The error counter is erased if reset.
AV COMM Diagnosis
• AV communication status and error counter is displayed.
• The error counter displays “OK” if any malfunction was not detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
• The error counter is erased if reset.
Handsfree Phone
The hands-free phone reception volume adjustment, microphone
and speaker test, and memory erase functions are also available.
Bluetooth
Passkey confirmation/change
• AV COMM CIRCUIT
• Rear View Camera Connection Error • A malfunction is detected in camera con-
trol unit power supply and ground cir-
cuits.
• Malfunction is detected on AV communi- cation signal between camera control
unit and AV control unit. Rear view camera control unit power sup-
ply and ground circuits. Refer to
AV- 7 2 ,
"REAR VIEW CAMERA CONTROL UNIT :
Diagnosis Procedure".
• AV COMM CIRCUIT
• Rear View Camera Connection Error
• Rear View Camera Control Unit Connec-
tion Error • Malfunction is detected in AV communi-
cation circuit between camera control
unit and AV control unit.
• Malfunction is detected on AV communi- cation signal between camera control
unit and AV control unit. AV communication circuit between Camera
control unit and AV control unit.
Error item
DescriptionPossible malfunction factor/Action to take
ALNIA0227GB
ALNIA0265GB
ALNIA0228GB
Revision: December 20092009 QX56

AV-44
< COMPONENT DIAGNOSIS >[AUDIO SYSTEM]
U1201 AV CONTROL UNIT
U1201 AV CONTROL UNIT
DescriptionINFOID:0000000004110619
Replace the AV control unit if this DTC is displayed. Refer to
AV-168, "Removal and Installation".
DTC LogicINFOID:0000000003776800
DTC DETECTION LOGIC
Part name Description
AV CONTROL UNIT • Integrates HDD (hard disk dr
ive) allowing map data and music data to be
stored.
• It is the master unit of the MULTI AV system, and it is connected to each control unit by means of communication. It operates each system according to com-
munication signals from the AV control unit.
• The AV control unit includes the audio, hands-free phone, voice control, navi- gation, and vehicle information functions.
• It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
• It inputs the automatic brightness ON/OFF signals that are required for the dis- play dimming control.
• It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTC CONSULT-III display Detection conditionAction to take
U1201 GYRO NO CONN
[U1201] An internal malfunction is detected in AV control unit (gy-
rocompass disconnection). Replace AV control unit. Refer
to
AV- 1 6 8 , "
Removal and Instal-
lation".
Revision: December 20092009 QX56

AV
U1204 GPS COMMAV-45
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
U1204 GPS COMM
DescriptionINFOID:0000000004110653
Replace the AV control unit if this DTC is displayed. Refer to AV-168, "Removal and Installation".
DTC LogicINFOID:0000000003776802
DTC DETECTION LOGIC
Part name Description
AV CONTROL UNIT • Integrates HDD (hard disk
drive) allowing map data and music data to be
stored.
• It is the master unit of the MULTI AV system, and it is connected to each control unit by means of communication. It operates each system according to com-
munication signals from the AV control unit.
• The AV control unit includes the audio, hands-free phone, voice control, navi- gation, and vehicle information functions.
• It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
• It inputs the automatic brightness ON/OFF signals that are required for the dis- play dimming control.
• It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTC CONSULT-III display Detection conditionAction to take
U1204 GPS COMM
[U1204] An internal malfunction is detected in AV control unit (GPS
malfunction). Replace AV control unit. Refer
to
AV-168, "
Removal and Instal-
lation".
Revision: December 20092009 QX56

AV-46
< COMPONENT DIAGNOSIS >[AUDIO SYSTEM]
U1205 GPS ROM
U1205 GPS ROM
DescriptionINFOID:0000000004110654
Replace the AV control unit if this DTC is displayed. Refer to
AV-168, "Removal and Installation".
DTC LogicINFOID:0000000003776804
DTC DETECTION LOGIC
Part name Description
AV CONTROL UNIT • Integrates HDD (hard disk dr
ive) allowing map data and music data to be
stored.
• It is the master unit of the MULTI AV system, and it is connected to each control unit by means of communication. It operates each system according to com-
munication signals from the AV control unit.
• The AV control unit includes the audio, hands-free phone, voice control, navi- gation, and vehicle information functions.
• It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
• It inputs the automatic brightness ON/OFF signals that are required for the dis- play dimming control.
• It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTC CONSULT-III display Detection conditionAction to take
U1205 GPS ROM
[U1205] An internal malfunction is detected in AV control unit (GPS
malfunction). Replace AV control unit. Refer
to
AV- 1 6 8 , "
Removal and Instal-
lation".
Revision: December 20092009 QX56

AV
U1206 GPS RAMAV-47
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
U1206 GPS RAM
DescriptionINFOID:0000000004110655
Replace the AV control unit if this DTC is displayed. Refer to AV-168, "Removal and Installation".
DTC LogicINFOID:0000000003776806
DTC DETECTION LOGIC
Part name Description
AV CONTROL UNIT • Integrates HDD (hard disk
drive) allowing map data and music data to be
stored.
• It is the master unit of the MULTI AV system, and it is connected to each control unit by means of communication. It operates each system according to com-
munication signals from the AV control unit.
• The AV control unit includes the audio, hands-free phone, voice control, navi- gation, and vehicle information functions.
• It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
• It inputs the automatic brightness ON/OFF signals that are required for the dis- play dimming control.
• It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTC CONSULT-III display Detection conditionAction to take
U1206 GPS RAM
[U1206] An internal malfunction is detected in AV control unit (GPS
malfunction). Replace AV control unit. Refer
to
AV-168, "
Removal and Instal-
lation".
Revision: December 20092009 QX56

AV-48
< COMPONENT DIAGNOSIS >[AUDIO SYSTEM]
U1207 GPS RTC
U1207 GPS RTC
DescriptionINFOID:0000000004110656
Replace the AV control unit if this DTC is displayed. Refer to
AV-168, "Removal and Installation".
DTC LogicINFOID:0000000003776808
DTC DETECTION LOGIC
Part name Description
AV CONTROL UNIT • Integrates HDD (hard disk dr
ive) allowing map data and music data to be
stored.
• It is the master unit of the MULTI AV system, and it is connected to each control unit by means of communication. It operates each system according to com-
munication signals from the AV control unit.
• The AV control unit includes the audio, hands-free phone, voice control, navi- gation, and vehicle information functions.
• It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
• It inputs the automatic brightness ON/OFF signals that are required for the dis- play dimming control.
• It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTC CONSULT-III display Detection conditionAction to take
U1207 GPS RTC
[U1207] An internal malfunction is detected in AV control unit (GPS
malfunction). Replace AV control unit. Refer
to
AV- 1 6 8 , "
Removal and Instal-
lation".
Revision: December 20092009 QX56

AV
U1216 AV CONTROL UNITAV-49
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
U1216 AV CONTROL UNIT
DescriptionINFOID:0000000004110657
Replace the AV control unit if this DTC is displayed. Refer to AV-168, "Removal and Installation".
DTC LogicINFOID:0000000003776810
Part name Description
AV CONTROL UNIT • Integrates HDD (hard disk
drive) allowing map data and music data to be
stored.
• It is the master unit of the MULTI AV system, and it is connected to each control unit by means of communication. It operates each system according to com-
munication signals from the AV control unit.
• The AV control unit includes the audio, hands-free phone, voice control, navi- gation, and vehicle information functions.
• It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
• It inputs the automatic brightness ON/OFF signals that are required for the dis- play dimming control.
• It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTC Display contents of CONSULT-III DTC Detection Condition Action to take
U1216 CAN CONT
[U1216] Internal malfunction of AV co
ntrol unit (CAN controller) is
detected. Replace AV control unit.
Refer to AV- 1 6 8 , "
Remov-
al and Installation".
Revision: December 20092009 QX56