B2128 INFINITI QX56 2010 Factory Service Manual

ADP-2
DTC Logic ...............................................................35
Diagnosis Procedure .............................................35
B2117 ADJ PEDAL MOTOR .............................36
Description ..............................................................36
DTC Logic ...............................................................36
Diagnosis Procedure .............................................36
B2118 TILT SENSOR ........................................38
Description ........................................................... ...38
DTC Logic ...............................................................38
Diagnosis Procedure .............................................38
B2120 ADJ PEDAL SENSOR ...........................40
Description ........................................................... ...40
DTC Logic ...............................................................40
Diagnosis Procedure .............................................40
B2126 DETENT SW ...........................................42
Description ........................................................... ...42
DTC Logic ...............................................................42
Diagnosis Procedure .............................................42
B2128 UART COMMUNICATION LINE ............44
Description ........................................................... ...44
DTC Logic ...............................................................44
Diagnosis Procedure .............................................44
POWER SUPPLY AND GROUND CIRCUIT .....46
BCM ........................................................................ ...46
BCM : Diagnosis Procedure ...................................46
DRIVER SEAT CONTROL UNIT ........................... ...47
DRIVER SEAT CONTROL UNIT :
Diagnosis Procedure .............................................
47
DRIVER SEAT CONTROL UNIT : Special Repair
Requirement ........................................................ ...
48
AUTOMATIC DRIVE POSITIONER CONTROL
UNIT ....................................................................... ...
48
AUTOMATIC DRIVE POSITIONER CONTROL
UNIT : Diagnosis Procedure ............................... ...
48
AUTOMATIC DRIVE POSITIONER CONTROL
UNIT : Special Repair Re quirement .......................
48
SLIDING SWITCH ..............................................50
Description ........................................................... ...50
Component Function Check .................................50
Diagnosis Procedure .............................................50
Component Inspection ............................................51
RECLINING SWITCH ........................................53
Description ........................................................... ...53
Component Function Check .................................53
Diagnosis Procedure .............................................53
Component Inspection ............................................54
LIFTING SWITCH (FRONT) ..............................56
Description ........................................................... ...56
Component Function Check .................................56
Diagnosis Procedure .............................................56
Component Inspection ......................................... ...57
LIFTING SWITCH (REAR) ................................59
Description ........................................................... ...59
Component Function Check ..................................59
Diagnosis Procedure ..............................................59
Component Inspection ............................................60
TILT SWITCH ....................................................62
Description ........................................................... ...62
Component Function Check ..................................62
Diagnosis Procedure ..............................................62
Component Inspection ............................................63
PEDAL ADJUSTING SWITCH ..........................65
Description ........................................................... ...65
Component Function Check ..................................65
Diagnosis Procedure ..............................................65
Component Inspection ............................................67
SEAT MEMORY SWITCH .................................68
Description ..............................................................68
Component Function Check ..................................68
Diagnosis Procedure ..............................................68
Component Inspection ............................................69
DOOR MIRROR REMOTE CONTROL
SWITCH .............................................................
70
CHANGEOVER SWITCH ....................................... ...70
CHANGEOVER SWITCH : Description ..................70
CHANGEOVER SWITCH : Component Function
Check ......................................................................
70
CHANGEOVER SWITCH : Diagnosis Procedure ...70
CHANGEOVER SWITCH : Component Inspec-
tion ..........................................................................
72
MIRROR SWITCH .................................................. ...72
MIRROR SWITCH : Description .............................72
MIRROR SWITCH : Component Function Check ...72
MIRROR SWITCH : Diagnosis Procedure ..............72
MIRROR SWITCH : Component Inspection ...........74
POWER SEAT SWITCH GROUND CIRCUIT ...76
Diagnosis Procedure ..............................................76
DETENTION SWITCH .......................................77
Description ........................................................... ...77
Component Function Check ..................................77
Diagnosis Procedure ..............................................77
FRONT DOOR SWITCH (DRIVER SIDE) .........79
Description ........................................................... ...79
Component Function Check ...................................79
Diagnosis Procedure ...............................................79
Component Inspection ............................................80
SLIDING SENSOR ............................................81
Description ..............................................................81
Component Function Check ..................................81
Diagnosis Procedure ..............................................81
Revision: April 20092010 QX56

ADP-44
< COMPONENT DIAGNOSIS >
B2128 UART COMMUNICATION LINE
B2128 UART COMMUNICATION LINE
DescriptionINFOID:0000000005147474
Driver seat control unit performs UART communication with the automatic drive positioner control unit using 2
communication lines, TX and RX line. Driver seat cont rol unit receives the operation signals of pedal adjusting
switch, door mirror remote control switch, set switch and memory switch and the position signals of adjustable
pedal sensor and door mirror sensor from the automatic drive positioner control unit and transmits the opera-
tion request signal.
DTC LogicINFOID:0000000005147475
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2. STEP 2
Operate pedal adjusting switch for more than 2 seconds.
>> GO TO 3
3. PROCEDURE 3
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-44, "DiagnosisProcedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000005147476
Regarding Wiring Diagram information, refer to ADP-119, "Wiring Diagram".
1. CHECK UART COMMUNICATION LINE CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect driver seat contro l unit and automatic drive posi-
tioner control unit.
3. Check continuity between driver seat control unit harness con- nector and automatic drive positioner control unit harness con-
nector.
DTC No. Trouble diagnosis name DTC detecting conditionPossible cause
B2128 UART COMM The communication between driver seat control unit
and automatic drive positioner control unit is interrupt-
ed for a period of time. • UART communication line
(UART communication line is
open or shorted)
• Driver seat control unit
• Automatic drive positioner control unit
Driver seat control unit connector Te r m i n a lAutomatic drive positioner
control unit connector Terminal Continuity
PIIA4598E
Revision: April 20092010 QX56

B2128 UART COMMUNICATION LINEADP-45
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
4. Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-38, "Intermittent Incident".
NO >> Repair or replace harness.
B202 1
M33 10
Ye s
17 26
Driver seat control unit con- nector Te r m i n a l
GroundContinuity
B202 1
No
17
Revision: April 20092010 QX56

ADP-134
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
NOTE:
The front seat LH position and pedal adjustment functions (see the following table) operate simultaneously in
the order of priority.
*: In conjunction with sliding the seat, the door mirrors are positioned.
CANCEL OF FAIL-SAFE MODE
The mode is cancelled when the A/T selector lever is shifted to P position from any other position.
DTC IndexINFOID:0000000005147579
*1:
• 0: Current malfunction is present
• 1-39: Displayed if any previous malfunction is present when current condition is normal. The numeral value increases by one at each
IGN ON to OFF cycle from 1 to 39. The counter remains at 39 even if the number of cycles exceeds it. However, the counter is re set
to 1 if any malfunction is detected again, the normal operation is resumed and the ignition switch is turned from OFF to ON. OPERATED PORTION
T2
Seat sliding Approx. 0.1 sec.
Seat reclining Same as above
Seat lifting (Front) Same as above
Seat lifting (Rear) Same as above
Pedal adjust Same as above
Priority Function PriorityFunction
1 Seat sliding, (door mirro r LH/RH)* 4Seat lifter-FR
2 Pedal 5Seat lifter-RR
3 Seat reclining
CONSULT-III
display Timing
*1
Item
Reference page
Current mal-
function Previous mal-
function
CAN COMM CIRCUIT
[U1000] 0
1-39 CAN communication ADP-31
SEAT SLIDE
[B2112]0
1-39 Seat slide motor output ADP-32
SEAT RECLINING
[B2113]0
1-39 Seat reclin ing motor output ADP-33
SEAT LIFTER FRONT
[B2114] 0
1-39 Seat lifting motor front output ADP-36
SEAT LIFTER REAR
[B2115]0
1-39 Seat lifting motor rear output ADP-36
TILT MOTOR
[B2116]0
1-39 Tilt motor output ADP-105
ADJ PEDAL MOTOR
[B2117]0
1-39 Pedal adjusting motor output ADP-36
TILT SENSOR
[B2118]0
1-39 Tilt sensor input ADP-38
ADJ PEDAL SENSOR
[B2120]0
1-39 Pedal adjusting sensor input ADP-36
DETENT SW
[B2126]0
1-39 Park position switch condition ADP-42
UART COMM
[B2128]0
1-39 UART communication ADP-44
Revision: April 20092010 QX56