ignition INFINITI QX56 2011 Factory Service Manual

BCS-30
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)INFOID:0000000006376456
DATA MONITOR
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT)INFOID:0000000006376457
DATA MONITOR
KEY CYL UN-SW
[On/Off] Unlock switch status received from door key cylinder switch
TRNK/HAT MNTR
[On/Off] NOTE:
The item is indicated, but not monitored.
RKE-LOCK
[On/Off] Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off] Unlock signal status received from remote keyless entry receiver
Monitor item
[Unit] Description
Test item Operation Description
BATTERY SAVER Off Cuts the interior room lamp power supply to turn interior room lamps OFF.
On Outputs the interior room lamp power supply to turn interior room lamps ON.*
Monitor Item Contents
PUSH SW Indicates [On/Off] condition of push switch
UNLK SEN -DR Indicates [On/Off] condition of unlock sensor
VEH SPEED 1 Indicates [Km/h] condition of ve hicle speed signal from combination meter
TR/BD OPEN SW Indicates [On/Off] condition of back door opener switch
TRNK/HAT MNTR NOTE:
This item is displayed, but cannot be monitored
RKE-TR/BD NOTE:
This item is displayed, but cannot be monitored
Monitored Item Description
REQ SW -DR Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -RR NOTE:
This item is displayed, but cannot be monitored.
REQ SW -RL NOTE:
This item is displayed, but cannot be monitored.
REQ SW -BD/TR Indicates [ON/OFF] condition of back door request switch.
PUSH SW Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN -DR Indicates [ON/OFF] condition of driver door UNLOCK status.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
Revision: 2010 May2011 QX56

BCS
DIAGNOSIS SYSTEM (BCM)BCS-31
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
B A
O P
N
WORK SUPPORT
ACTIVE TEST
RETAIND PWR
RETAIND PWR : CONSULT-III F
unction (BCM - RETAINED PWR)INFOID:0000000006376459
Data monitor
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III F unction (BCM - SIGNAL BUFFER)INFOID:0000000006274818
DATA MONITOR
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from door lock/unlock switch LH and RH.
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch LH and RH.
KEY CYL LK-SW Indicates [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW Indicates [ON/OFF] condition of unlock signal from door key cylinder.
TR/BD OPEN SW Indicates [ON/OFF] condition of back door opener switch.
TRNK/HAT MNTR NOTE:
This item is displayed, but cannot be monitored.
RKE-LOCK Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD NOTE:
This item is displayed, but cannot be monitored.
Monitored Item Description
Service Item Description
SECURITY ALARM SET This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT-III screen.
Test Item Description
THEFT IND This test is able to check security indicator lamp operation. Security indicator lamp is turned on
when “ON” on CONSULT-III screen is touched.
VEHICLE SECURITY HORN This test is able to check horn operation. Horn is activated for 0.5 seconds after “ON” on CONSULT-
III screen is touched.
HEADLAMP(HI) This test is able to check headlamp operation. Headlamps are activated for 0.5 seconds after “ON”
on CONSULT-III screen is touched.
FLASHER This test is able to check hazard warning lamp operation. Hazard warning lamps are activated after
“ON” on CONSULT-III screen is touched.
Monitor Item Description
DOOR SW-DR Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS Indicates [ON/OFF] condition of passenger side door switch.
Monitor item [UNIT] Description
PUSH SW
[Off/On] Displays the status of the push-button ignition switch (push switch) judged by BCM.
Revision: 2010 May2011 QX56

BCS
BCM
BCS-35
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N
OPTICAL SENSOR
NOTE:
The item is indicated, but not monitored. Off
RAIN SENSOR No rain (or very light rain) Off
Light rain
LOW
Heavy rain HIGH
When liquid is splashed on the front window SPLSH
Rain sensor internal error NG
REQ SW -DR Driver door request switch is not pressed Off
Driver door request switch is pressed On
REQ SW -AS Passenger door request switch is not pressed Off
Passenger door request switch is pressed On
REQ SW -RR NOTE:
The item is indicated, but not monitored.
Off
REQ SW -RL NOTE:
The item is indicated, but not monitored. Off
REQ SW -BD/TR Back door request switch is not pressed Off
Back door request switch is pressed On
PUSH SW Push-button ignition switch (push switch) is not pressed Off
Push-button ignition switch (push switch) is pressed On
CLUCH SW NOTE:
The item is indicated, but not monitored. Off
BRAKE SW 1 The brake pedal is not depressed Off
The brake pedal is depressed On
BRAKE SW 2 The brake pedal is depressed when No. 7 fuse is blown Off
The brake pedal is not depressed when No. 7 fuse is blown, or No. 7 fuse
is normal
On
DETE/CANCL SW Selector lever in P position Off
Selector lever in any position other than P On
SFT PN/N SW Selector lever in any position other than P and N Off
Selector lever in P or N position On
S/L -LOCK Steering is locked Off
Steering is unlocked On
S/L -UNLOCK Steering is unlocked Off
Steering is locked On
S/L RELAY-F/B Steering is unlocked Off
Steering is locked On
UNLK SEN -DR Driver door is locked Off
Driver door is unlocked On
PUSH SW -IPDM Push-button ignition switch (push-switch) is not pressed Off
Push-button ignition switch (push-switch) is pressed On
IGN RLY1 -F/B Ignition switch in OFF or ACC position Off
Ignition switch in ON position On
DETE SW -IPDM Selector lever in any position other than P Off
Selector lever in P position On
SFT PN -IPDM Selector lever in any position other than P and N Off
Selector lever in P or N position On
Monitor Item Condition Value/Status
Revision: 2010 May2011 QX56

BCS
BCM
BCS-41
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N8
(V) Ground Power window
switch communica-
tion Input/
Output Ignition switch ON
9.0 - 10 V
9
(R) Ground Stop lamp switch 1 Input Stop lamp
switchOFF (Brake pedal is not
depressed)
0 V
ON (Brake pedal is de-
pressed) Battery voltage
11
(R) Ground
Light and rain sensor
serial link Input/
Output Ignition switch OFF 12 V
Ignition switch ON
8.0 - 9.0 V
14
(P/B) Ground Optical sensor Input Ignition switch
ONWhen bright outside of the
vehicle
Close to 5 V
When dark outside of the
vehicle Close to 0 V
16
(L/O) Ground Dimmer signal Output Ignition switch
ONEither of the following
conditions
 Lighting switch OFF
 The area around the ve-
hicle is bright (Shine a
light on the optical sen-
sor) 0 V
The area around the vehi-
cle is dark (Block the light
from the optical sensor) 12 V
17
(Y/G) Ground Sensor power sup-
ply
Output Ignition switch OFF, ACC 0 V
ON 5 V
18
(B/Y) Ground Receiver and sensor
ground Input Ignition switch ON 0 V
19
(BR) Ground Remote keyless en-
try receiver power
supply
Output Ignition switch OFF
Terminal No.
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIA7023E
JPMIA0156GB
JMKIA3838GB
Revision: 2010 May2011 QX56

BCS-42
< ECU DIAGNOSIS INFORMATION >
BCM
20
(G/R) Ground Remote keyless en-
try receiver commu-
nication
InputWaiting
Signal receiving
21
(P) Ground NATS antenna amp. Input/
Output During waiting Ignition switch is pressed
while inserting the key into
the key slot. Just after pressing ignition
switch. Pointer of tester should move.
22
(W/B) Ground Remote keyless en-
try receiver RSSI
InputWaiting 0 V
Signal receiving
23
(GR/R) GroundSecurity indicator
lamp
OutputSecurity indica-
tor lamp ON 0 V
Blinking (Ignition switch
OFF)
11.0 - 12.0 V
OFF Battery voltage
24*
(SB) Ground Dongle link
Input/
Output Ignition switch OFF 5 V
25
(LG/R) Ground NATS antenna amp.
Input/
Output During waiting Ignition switch is pressed
while inserting the key into
the key slot. Just after pressing ignition
switch. Pointer of tester should
move.
29
(W) Ground Hazard switch Input Hazard switch OFF 12 V
ON 0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −JMKIA3838GB
JMKIA3841GB
JMKIA3838GB
JPMIA0590GB
Revision: 2010 May2011 QX56

BCS-46
< ECU DIAGNOSIS INFORMATION >
BCM
44
(G/W) Ground Rear wiper stop po-
sition
InputIgnition switch
ON Rear wiper stop position 12 V
Any position other than
rear wiper stop position
0 V
45
(W) Ground Passenger door
switch
InputPassenger door
switch OFF (When passenger
door closed)
7.0 - 8.0 V
ON (When passenger
door opened) 0 V
46
(GR) Ground Rear RH door switch Input Rear RH door
switchOFF (When rear RH door
closed)
7.0 - 8.0 V
ON (When rear RH door
opened) 0 V
47
(GR/R) Ground Driver door switch Input
Driver door
switchOFF (When driver door
closed)
7.0 - 8.0 V
ON (When driver door
opened) 0 V
48
(O) Ground Rear LH door switch Input
Rear LH door
switchOFF (When rear LH door
closed)
7.0 - 8.0 V
ON (When rear door LH
opened) 0 V
49
(BR/Y) Ground Luggage room lamp Output
Luggage room
lampOFF 12 V
ON 0 V
51
(W/R) Ground
Back door request
switch Input
Back door re-
quest switch ON (Pressed) 0 V
OFF (Not pressed) 12 V
54
(L) Ground Rear wiper Output Rear wiper OFF (Stopped) 0 V
ON (Activated) 12 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIB4960J
PKIB4960J
PKIB4960J
PKIB4960J
Revision: 2010 May2011 QX56

BCS
BCM
BCS-47
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N
55
(G) Ground Rear door UNLOCK Output Rear door UNLOCK (Actuator is acti-
vated)
12 V
Other then UNLOCK (Ac-
tuator is not activated) 0 V
56
(W/R) Ground Interior room lamp
power supply OutputInterior room lamp battery saver is activated.
(Cuts the interior room
lamp power supply) 0 V
Interior room lamp battery saver is not acti-
vated.
(Outputs the interior room lamp power sup-
ply) 12 V
57
(LG) Ground Battery power sup-
ply
Input Ignition switch OFF Battery voltage
59
(G) Ground Passenger door UN-
LOCK
Output Passenger door UNLOCK (Actuator is acti-
vated)
12 V
Other then UNLOCK (Ac-
tuator is not activated) 0 V
60
(G) Ground Turn signal LH Output Ignition switch
ONTurn signal switch OFF 0 V
Turn signal switch LH
6.0 - 7.0 V
61
(G/Y) Ground Turn signal RH Output Ignition switch
ONTurn signal switch OFF 0 V
Turn signal switch RH
6.0 - 7.0 V
62
(R) Ground Step lamp Output Step lamp ON 0 V
OFF 12 V
63
(BR) Ground Interior room lamp
timer control
OutputInterior room
lamp OFF 12 V
ON 0 V
64
(GR/R) Ground Cranking request input
Ignition switch
ONEngine stopped (Selector
lever is in P position)
0 V
Engine stopped (Selector
lever is not in P position) 12 V
Engine running 12 V
65
(R) Ground All doors, fuel lid
LOCK
Output All doors, fuel lid LOCK (Actuator is activat-
ed)
12 V
Other then LOCK (Actua-
tor is not activated) 0 V
Terminal No.
(Wire color) Description
Condition
Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIC6370E
PKIC6370E
Revision: 2010 May2011 QX56

BCS-48
< ECU DIAGNOSIS INFORMATION >
BCM
66
(V) Ground Driver door, fuel lid
UNLOCK OutputDriver door, fuel
lid UNLOCK (Actuator is acti-
vated)
12 V
Other then UNLOCK (Ac-
tuator is not activated) 0 V
67
(B) Ground Ground Output Ignition switch ON 0 V
68
(Y) Ground P/W power supply
(IGN)
Output Ignition switch ON 12 V
69
(W) Ground
P/W power supply
(BAT) Output Ignition switch OFF 12 V
70
(Y) Ground Battery power sup-
ply Input Ignition switch OFF Battery voltage
72
(P) Ground Puddle lamp control Output Puddle lamp OFF 12 V
ON 0 V
73
(W) Ground ON indicator lamp Output Ignition switch OFF (LOCK indicator is
not illuminated)
Battery voltage
ON 0 V
74
(Y/B) Ground Trailer turn signal
RH control
OutputIgnition switch
ON Turn signal switch OFF Battery voltage
Turn signal switch RH
6.0 - 7.0 V
75
(LG/R) Ground
Driver door request
switch Input
Driver door re-
quest switch ON (Pressed) 0 V
OFF (Not pressed) 12 V
76
(P/L) Ground
Passenger door re-
quest switch Input
Passenger door
request switch ON (Pressed) 0 V
OFF (Not pressed) 12 V
77
(O/L) Ground Trailer turn signal LH
control
OutputIgnition switch
ON Turn signal switch OFF Battery voltage
Turn signal switch LH
6.0 - 7.0 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
PKIC6370E
PKIC6370E
Revision: 2010 May2011 QX56

BCS
BCM
BCS-49
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
B A
O P
N
78
(P/B) Ground
Driver door antenna
(+) OutputWhen the driver
door request
switch is operat-
ed with ignition
switch OFF When Intelligent Key is
not in the antenna detec-
tion area
When Intelligent Key is in
the antenna detection
area
79
(V) Ground Driver door antenna
(-)
OutputWhen the driver
door request
switch is operat-
ed with ignition
switch OFF When Intelligent Key is
not in the antenna detec-
tion area
When Intelligent Key is in
the antenna detection
area
80
(LG/B) Ground Passenger door an-
tenna (+) OutputWhen the pas-
senger door re-
quest switch is
operated with
ignition switch
OFF When Intelligent Key is
not in the antenna detec-
tion area
When Intelligent Key is in
the antenna detection
area
Terminal No.
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
JMKIA3838GB
JMKIA3839GB
JMKIA3838GB
JMKIA3839GB
JMKIA3838GB
JMKIA3839GB
Revision: 2010 May2011 QX56

BCS-50
< ECU DIAGNOSIS INFORMATION >
BCM
81
(Y/R) Ground
Passenger door an-
tenna (-) OutputWhen the pas-
senger door re-
quest switch is
operated with
ignition switch
OFF When Intelligent Key is
not in the antenna detec-
tion area
When Intelligent Key is in
the antenna detection
area
82
(W/G) Ground Back door antenna
(+)
OutputWhen the back
door request
switch is operat-
ed with ignition
switch OFF When Intelligent Key is
not in the antenna detec-
tion area
When Intelligent Key is in
the antenna detection
area
83
(B/W) Ground Back door antenna (-
) OutputWhen the back
door request
switch is operat-
ed with ignition
switch OFF When Intelligent Key is
not in the antenna detec-
tion area
When Intelligent Key is in
the antenna detection
area
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+ −
JMKIA3838GB
JMKIA3839GB
JMKIA3838GB
JMKIA3839GB
JMKIA3838GB
JMKIA3839GB
Revision: 2010 May2011 QX56